Аква плюс для бассейна инструкция

Производитель: Русхимбасс

Дозирование: Необходимо 1-2 раза в неделю измерять pH воды тест-прибором и соответственно корректировать состав воды. Для повышения pH на 0,1 необходимо 100 мл на 10 куб. м. воды бассейна (или 10 мл на 1 куб. м.)

Код поставщика: 50003475

Назначение: АКВА-ПЛЮС повышает величину Ph воды в плавательных бассейнах всех типов

Страна-производитель: Россия

Состав: Содержит 20-25 % каустика мембранного качества, подготовленная вода, ингибиторы коррозии, комплексон

Остатки только по МФ: 0

Тип: Средство для чистки бассейна

Тип упаковки: Бутылка

Тип товара: Средство для чистки бассейна

Объём: 1.0000

489 руб.
Найти дешевле!

• Page 1
  Aqua Plus ® Automation and Chlorination Operation Manual for models PL-PLUS PL-PLUS-20 www.hayward.com…

• Page 2: Important Safety Instructions

  IMPORTANT SAFETY INSTRUCTIONS When using this electrical equipment, basic safety precautions should always be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS • • WARNING: Disconnect all AC power during installation. • WARNING: Water in excess of 100 degrees Fahrenheit may be hazardous to your health.

• Page 3: Table Of Contents

  Table of Contents System Overview Block Diagram…………… 1 Automation…………….1 Chlorination…………….1 Default Display…………… 2 Manual System Filter Pump…………….3 Operation Lights and Aux Outputs…………4 Pool/Spa Valves…………..4 Service………………4 Automatic System Using the Programming Buttons………. 5 Operation Programming Menu Flow Chart……….. 6 (Programming) Settings Menu…………….

• Page 4: System Overview Block Diagram

  System Overview The Hayward Aqua Plus is a multifunction pool controller used to fully manage your pool/spa system. The Aqua Plus can control pumps, valves, lighting, heaters, and chlorination. Although the Aqua Plus is easy to use, it is important to completely read through this operating manual before attempting to operate the control.

• Page 5: Default Display

  The actual amount of chlorination required to properly sanitize a pool varies due to bather load, rainfall, temperature, and the pool’s cleanliness. For pools larger than 40,000 gallons, the Aqua Plus can control one or more Hayward Aqua Rite chlorinators to supplement chlorine production.

• Page 6: Manual System Filter Pump

  Manual System Operation While the main objective of the Aqua Plus is to automate the operation of your pool/spa system, there may be certain times when you want to override the automatic operation and control the equipment manually. To operate the pool equipment manually while keeping the automation active, perform the following procedures.

• Page 7: Operation Lights And Aux Outputs

  (either manually or automatically), the dimmer output level will be the same as the last time that it was set. VSP Relay: This selection is used to configure a Lights/Aux output to supply power and control a Hayward Variable Speed pump (VSP).

• Page 8: Automatic System Using The Programming Buttons

  Automatic System Operation The Aqua Plus controls most of your pool equipment automatically in order to minimize the time spent working on your pool. Most of the pool equipment can be programmed to operate on a timeclock basis. In addition, the desired pool and spa temperatures and pool and spa chlorinator settings can be programmed.

• Page 9: Operation Programming Menu Flow Chart

  Programming Menu Flowchart The Aqua Plus’s six menus have many items that allow you to customize the operation of your pool/spa equipment. The chart below shows the Aqua Plus’s menus as well as each menu’s specific settings. default menu day and time denotes conditional items water temperature air temperature…

• Page 10: (Programming) Settings Menu

  The Default Menu is a series of informative displays (temperatures, salt levels, chlorinator settings, etc.) with nothing to set. The Aqua Plus will automatically switch to the default menu when no keys have been pressed for 2 minutes and will then scroll through each display. The Settings Menu and the Timers Menu are the menus you will be using most often to adjust the operation of your pool.

• Page 11
  only if an output is configured for a variable speed pump VSP Speed Settings Push to access Variable Speed Pump Speed Settings + to enter Move to previous/next configuration menu only if Filter is Variable Speed Filter Speed 1 Set the desired Filter Speed 1 from the Filter Lowest to the Filter Highest Move to next menu item only if Pool and Spa and Filter is Variable Speed Spa Speed…
• Page 12
  Adjust the current day of the week Set Day and Time Set Day and Time Wednesday 10:37P 10:37P Move to hours setting Adjust the current hour (including AM/PM if applicable) Set Day and Time Wednesday Move to minutes setting Adjust the current minute Set Day and Time Wednesday 10: Move to previous/next menu item…

• Page 13: Timers Menu

  Teach Wireless Push to start process + to start Move to previous/next menu item Press and hold Press any button on wireless remote wireless button Move to previous/next menu item Teach Wireless Move to previous/next menu item Successful Teach Wireless Move to previous/next menu item NOT Successful Teach Wireless…

• Page 14
  Adjust time setting Set Day and Time Filter T1-all Wednesday 10:37P 8:30A to 4:00P Move between start and stop times & to previous/next menu item Adjust time setting Filter T1-wkend 8:30A to 4:00P Move between start and stop times & to previous/next menu item Adjust time setting Filter T1-wkday 8:30A to 4:00P…
• Page 15
  Adjust time setting Set Day and Time Spa-all Wednesday 10:37P 6:00P to 9:00P Move between start and stop times & to previous/next menu item Adjust time setting Spa-wkend 6:00P to 9:00P Move between start and stop times & to previous/next menu item Adjust time setting Spa-wkday 6:00P to 9:00P…

• Page 16: Configuration Menu

  Set Day and Time Valve3-all Adjust time setting Adjust time s Wednesday 10:37P 8:30A to 4:00P Move between start and stop times & to previous/next menu item Valve3-wkend Adjust time setting 8:30A to 4:00P Move between start and stop times & to previous/next menu item Valve3-wkday Adjust time setting 8:30A to 4:00P…

• Page 17
  Pool/Spa Config. Push to access Pool/Spa options + to view/change Move to previous/next configuration menu Rotates between Pool Only (default), Spa Only and Pool/Spa Setup Pool and Spa Pool and Spa Move to next menu item if “Pool and Spa” is selected Spa — CountDn Adjust time setting (Manual On/Off, 0:05, 0:10, 0:15…, (default is 4:00)) 00:30…
• Page 18
  For the Hayward variable speed pump: The Filter relay is used to supply input power to the pump. The relay will be on when the filter pump output is on. When the filter pump output is off, the relay will be off.
• Page 19
  Freeze Protection Temperature Select the temperature to be used for freeze protection. Temperature is adjustable from 33ºF-42ºF (1ºC- 6ºC). 38ºF (3ºC) is default. This threshold will be used for all outputs that have freeze protection enabled. External Input Interlock When enabled, the filter pump will be forced off when the external input is active. Note that freeze protection will have precedence over this feature.
• Page 20
  Solar Config. Push to access solar options + to view/change Move to previous/next configuration menu Toggle between Enabled and Disabled (default) Solar Solar Disabled Move to next menu item or previous/next configuration menu if “Solar” is enabled Toggle between Enabled and Disabled (default) Solar Extend Solar-Extend Disabled Move to next menu item…
• Page 21
  Lights Config. Push to access Lights options + to view/change Move to previous/next configuration menu Lights Name Rotates between all available names Pool Light Move to next menu item or previous/next configuration menu Rotates between Manual On/Off (default), Countdown Timer, Low Speed- Filter, Lights Function Timeclock, Solar, and Super Chlorinate Manual On/Off…
• Page 22
  If “VSP” is selected, the Lights relay is used to supply power to a Hayward Variable Speed Pump (VSP). The relay will be on when the Lights output is on and off when the output is off . On, off and speed are controlled by commands sent to the VSP.
• Page 23
  If “VSP” is selected, the Aux relay is used to supply power to a Hayward Variable Speed Pump (VSP). The relay will be on when the Aux output is on and off when the output is off. On, off and speed are controlled by commands sent to the VSP.
• Page 24
  Valve3 Config. Push to access Valve3 options + to view/change Move to previous/next configuration menu Rotates Timeclock (default), Solar, In-floor Cleaner and Super Chlorinate Valve3 Function Solar Move to next menu item for all functions except solar and super chlorinate Toggle between Enabled and Disabled (default) Valve3 Interlock Valve3 Interlock…
• Page 25
  if AQL-SS-6B is connected 6B Spa Config. Push to access the 6 Button Spa Side Remote options + to view/change Move to previous/next configuration menu Select 6B Spa Rotates between all available remotes Move to next menu item Rotates between System Off, Pool/Spa, Filter, Lights, Heater1, 6B A, Button 1 Aux1 and Aux2 Pool/Spa…

• Page 26: Maintenance Menu

  Maintenance Menu (only displays if Sensing System is enabled) The Maintenance Menu will be displayed only if the optional AQL-CHEM is used and the Sensing System is enabled in the Chemistry Config. Wizard. This menu is used to perform functions relating to the AQL-CHEM ORP and pH sensing kit.

• Page 27: Quick «How To» Operate The Spa — Manually

  Quick “How To” Guide Operate the Spa—Manually 1. Press the “Pool/Spa” button to go to “spa-only” operation (right LED illuminated). In some cases, this may take more than one press of the button. 2. If the filter pump is not already on, press the “FILTER” button to turn it on. 3.

• Page 28: Start/Stop Superchlorination

  Note: Separate chlorinator output levels for the pool and spa must be set. If the valves are in the pool-only or spa spillover positions, then the chlorinator will operate according the pool setting. If the valves are in the spa-only position then the chlorinator will operate according to the spa setting.

• Page 29: Chlorinator Operation/Saturation Index

  Chlorinator Operation / Water Chemistry General Water Chemistry Salt is required only if you are using the chlorinator features on the Aqua Plus Control. If you are NOT using the chlorinator, it is recommended that you follow all of the other chemistry recommendations besides salt. Refer to the description of the Aqua Plus configuration menu for information on enabling/disabling the chlorinator (see page 13).

• Page 30: Water Chemistry Salt Level

  The pool’s chemistry must be balanced BEFORE activating the Aqua Plus’s optional chlorinator function. NOTE: If the pool does not have new water, add metal remover and non-copper based algaecide to the pool, per manufacturer’s instructions. This ensures a quick, troublefree transfer to the Aqua Plus system. Salt Salt Level Use the chart on the following page to determine how much salt in pounds or (Kgs) should be added to reach the…

• Page 33: System Maintenance Servicing And Cleaning The Turbo Cell

  System Maintenance To maintain maximum performance, it is recommended that you open and visually inspect the cell every 3 months or after cleaning your filter. The Aqua Plus will remind you to do this by displaying the message “Inspect/Clean Cell” after approximately 500 hours of operation. The Aqua Plus electrolytic cell has a self cleaning feature incorporated into the electronic control’s logic.

• Page 34: Troubleshooting & Service Mode

  While both of the features are primarily intended for the use of the professional service technician, their function is fully explained below. If you believe your system is not operating properly or have questions regarding the opera- tion, call the Hayward Technical Service Department from Monday through Friday, 8AM to 8PM EST at 888- 921-7665.

• Page 35
  • Filter VSP Drive Comm Error — If variable speed is selected for the Filter and the Hayward VSP drive controller is not responding. • Filter VSP Err: x — If variable speed is selected for the Filter and the Hayward VSP is indicating and error. x is the same decimal error displayed by the VSP itself.

• Page 36: Diagnostic Menu

  • ORP High — Check Chlor — If an ORP level of 950mV or higher is detected. Check the chlorinator for proper operation. • ORP High — Chlor Off — If an ORP level of 950mV or higher is detected and the chlorine feed mode is ORP Auto Sensing, the chlorinator has been turned off.

• Page 37
  AQL-CHEM Sensing Kit). The Aqua Plus will refer to these levels to determine how much chlorine to generate (ORP) and, if using an AQL-CHEM2 dispense kit, how much CO or acid to dispense (pH). Refer to the AQL-CHEM manual for specific information about these levels as well as the recommended ranges.
• Page 38
  Remote A r1.00 Move to previous/next menu item Available displays depend on configuration. If you call the Hayward Technical Service Dept. for assistance, they may ask for the software revisions of both the main unit and each of the display/ keypads or other devices that are attached to the system.
• Page 39
  (3) years. Hayward also warrants its Aqua Trol chlorination products to be free of defects in materials and workmanship, under normal use and service for a period of one (1) year. These warranties are applicable from the initial date of purchase on private residential swimming pools in the US and Canada.
• Page 40
  Add cyanuric acid to increase. Calcium 200 — 400 ppm Add calcium to increase. Drain and add water to decrease. Electrolytic Cell inspect & clean Refer to section in manual. 620 Division St. 092360D RevG Elizabeth, NJ 07207 Copyright © 2010 Hayward…

Химия для бассейнов: РН плюс гранулированный (Аква — плюс) (1 кг)

АКВА-ПЛЮС — повышение уровня рН (Карбонат натрия).
Применение:
1 кг препарата «Аква-плюс» достаточно для повышения уровня рН в бассейне объемом 100 м3 примерно на 0,2. Жесткая вода требует большей дозировки, а мягкая вода — меньшей.
Необходимое количество реагента растворить в воде в пластиковой емкости.
Полученный раствор разделить на несколько порций и по очереди равномерно распределить в воде бассейна. Перед дозированием каждой порции следует проверить изменение показателя рН.