Allen bradley 1336 plus инструкция на русском

1336 PLUS Language Module

Installation/Replacement

This publication will guide you through installation (or replacement)

of the 1336 PLUS Language Module.

ATTENTION: This drive contains ESD (Electrostatic

!

Discharge) sensitive parts and assemblies. Static control

precautions are required when installing, testing, servicing

or repairing this assembly. Component damage may result

if ESD control procedures are not followed. If you are not

familiar with static control procedures, reference A-B

publication 8000-4.5.2, «Guarding Against Electrostatic

Damage» or any other applicable ESD protection

handbook.

ATTENTION: To avoid a shock hazard, assure that all

!

power to the drive has been removed before proceeding with

the following procedure. In addition, verify that the DC bus

has discharged by measuring across the «+ DC» and «– DC»

terminals of TB1 with a voltmeter. The voltage should be

0.0V DC.

1. Check the version of firmware presently installed in the drive.

If the current version is 1.04 or greater, proceed to step 2.

If you have version 1.03, parameters 111-127 and 180 must be

checked. The value of each parameter must be greater than zero

and less than 212. If any value is outside of this range, reprogram

using the Program mode before proceeding to step 2.

Important: If parameters 127 and/or 180 are set to «0» (zero), these

must be reprogrammed to «1.»

If the above is not performed, an «EE Init Read» fault (F53) will

be issued when the drive is powered up with the new Language

Module.

2. Remove and lock-out all incoming power to the drive. Remove

the drive cover.

Instructions

Источник

2

1336 PLUS, 1336 PLUS II & 1336 FORCE™ NEMA Type 1 Enclosure Kit

Installation

Access to the top, bottom and sides of the drive chassis is required to

assemble the kit. If the open chassis drive is already installed, remove

and lock-out all power to the drive, then label and disconnect all

wiring. External wiring will have to be rerouted through enclosure

knockouts once the kit has been installed.

Figure 1

Enclosure Kits – 1336S/F-AA2 and -AA3

1. Mount the top, bottom and side plates to the chassis using the

supplied screws. Tighten all screws to 1.7 N-m (15 lb.-in.).

2. Install the front cover by sliding it up, then down to engage the

slots into the angled tabs. Swing the cover bottom «in» and secure

it with the captive screw. Tighten to 0.7 N-m (6 lb.-in.).

Figure 2

EMC Enclosure Kits – 1336S/F-AE2 and -AE3

1. Mount the bottom plate to the chassis using the supplied screws.

2. Slide enclosure assembly over the chassis as shown.

3. Fasten the assembly to the chassis using the supplied screws.

Tighten all screws to 1.7 N-m (15 lb.-in.).

Figure 3

Enclosure Kits – 1336S/F/T-AA4 and -AA5

1. Slide the side plates over the chassis tabs as shown.

2. Attach the top and bottom plates to the side plates by sliding the

tabs into the corresponding slots. Fasten the assembly to the

chassis using the supplied screws. Tighten all screws to 1.5 N-m

(13 lb.-in.).

3. Install the front cover by sliding it up, then down to engage the

slots into the angled tabs. Swing the cover bottom «in» and secure

it with the captive screw. Tighten to 0.7 N-m (6 lb.-in.).

Figure 4

EMC Enclosure Kits – 1336S/F/T-AE4 and -AE5

1. Mount the bottom plate to the chassis using the supplied screws.

2. 1336

drives using the AE4 Enclosure Kit require

PLUS

II

replacement of a ribbon cable. Remove the ribbon cable between

the Main Control Board and Gate Drive Board (see Figure 4).

Replace this cable with the new supplied cable (with ferrite

block). Position the cable/block as needed to prevent obstruction

with the enclosure being installed.

3. Slide enclosure assembly over chassis as shown.

4. Fasten the assembly to the chassis using the supplied screws.

Tighten all screws to 1.5 N-m (13 lb.-in.).

Источник

Table of Contents for Allen-Bradley 1336 PLUS II:

  • 1336 PLUS II Firmware Download Module 9 16. Select “ (2) Send File to drive .” A message will appear regarding correct jumper installation. A string of C’s will then appear, indicating that the drive is waiting for the file to be downloaded. 17. From the Transfer menu (top of screen), select “Send File.” Enter the file path (location of .bin file) and choose “Xmodem” as the protocol, then select “Send.” The download process will continue until complete. The screen will be updated as progress continues. The STOP LED on the Main Control Board

  • 1336 PLUS II Firmware Download Module 5 Establishing Communications with the Drive Setting Up the Communications Program 10. Start the XMODEM communications program. The following examples demonstrate the use of HyperTerminal (supplied with Windows 95 operating system). Other programs will be similar. From the Start menu, choose: “ Programs -> Accessories -> HyperTerminal ” 11. With the Hyperterminal window active, double click the Hypertrm.exe icon A. Connection Description window – enter a name and select “OK.” Allen-Bradley

  • 12 1336 PLUS II Firmware Download Module Troubleshooting Table A General Troubleshooting Table B Drive Related Faults Netscape Navigator is a registered trademark of Netscape Communications Corporation IBM is a registered trademark of International Business Machines Corporation Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corporation Condition Cause Action “Transfer cancelled by remote system” Jumper J20 not installed. End the

  • 4 1336 PLUS II Firmware Download Module C. Verify the files using the information below. To properly complete all download functions, certain information contained in a “readme” file must be read and recorded. The “readme” file will have the same version number and a “.txt” file type (i.e. Read1004.txt). You should obtain both files (i.e. V_x.xxxf.bin and Readxxxx.txt). Important: Verify that the “.bin” file has an “f” (V_x.xxx f.xxx). If you cannot locate the correct file, c

  • Instructions This document provides information on upgrading the 1336 PLUS II firmware, including a description of the Flash memory used in the drive and the procedures required for downloading the latest firmware revision. For detailed drive information, refer to 1336 PLUS II User Manual, publication 1336 PLUS-5.3. What is Flash Memory? The drive firmware (including parameter layout and operating algorithms) resides in a form of programmable read-only memor

  • 1336 PLUS II Firmware Download Module 11 18. If errors occurred in the transfer, the screen may display one of the following: • Error in Constant Block • Error in Program Block • Error in DSP Block • Error in Text and Language Block If errors are indicated, press the Enter key on the computer and return to step 10 on page 5 to repeat the entire process from that point. 19. If no errors have occurred . . . A. Remove all power from th

  • 10 1336 PLUS II Firmware Download Module If the “packet” value is not incrementing and the time remaining block is continually incrementing, the file transfer is not taking place. If this occurs, cancel the operation and repeat the entire procedure, verifying jumper placement, cabling and communications setup. When the transfer is complete, the screen will indicate that the file was successfully transferred and checksums are complete.

  • 8 1336 PLUS II Firmware Download Module 14. The default baud rate of 9600 should be acceptable under most conditions. However, to facilitate faster file transfers, the baud rate can be changed for communications up to the maximum drive rate of 115.2 kb (or the maximum computer rate). To use the default rate, proceed to step 15. A. Select “ (3) Set Baud rate ” by pressing the “3” key. B. Select the desired baud rate and note instructions disp

  • 1336 PLUS II Firmware Download Module 7 Transferring the File to the Drive 12. Press the Enter key on your computer once to signal the drive – an introduction screen will be displayed. 13. Press “F” to enter the Flash Mode. You are now prompted to confirm your choice “Are you sure?” (y or n). Important: During the time that the flash memory is being upgraded,the drivewillbeina “non-operationalstate” and will not have the ability to control the motor. Be certain that placing the drive in a non operational state is acceptable. Press “Y�

  • 2 1336 PLUS II Firmware Download Module Main Control Board Power Requirements In order to upgrade firmware, the Main Control Board must have power applied. This can be accomplished through one of the following methods: • Application of AC line voltage per instructions in Chapter 2 of the 1336 PLUS II User Manual. This is the normal method for installed drives. • External power supply through the auxiliary 24V DC input at terminal block TB4 (B frame

  • 6 1336 PLUS II Firmware Download Module B. Phone Number window – locate the Connect using: menu and choose “Direct to Com1,” then select “OK.” If a different COM port is being used, substitute the appropriate one for your computer setup. C. COM Properties window – locate the Bits per second menu and choose “9600” (default of the drive). Choose “None” for Flow control and then select “OK.”

Questions, Opinions and Exploitation Impressions:

You can ask a question, express your opinion or share our experience of Allen-Bradley 1336 PLUS II device using right now.

Источник

Металлический форум

  • Уже зарегистрированы? Войти  

  • Регистрация

Изменение в правилах «Опознайки»

Один объект для опознания — одна тема.
Запрещается размещать групповые фотографии или несколько разных объектов для опознания. 

Евгений87

Для публикации сообщений создайте учётную запись или авторизуйтесь

Вы должны быть пользователем, чтобы оставить комментарий

Войти

Уже есть аккаунт? Войти в систему.

Войти

Источник

Quick Start Manual for Allen-Bradley 1336 PLUS II Controller, Control Unit (6 pages)

Specifications:

1296/1296551-1336_plus_ii.pdf file (22 Feb 2023)

Accompanying Data:

Allen-Bradley 1336 PLUS II Controller, Control Unit PDF Quick Start Manual (Updated: Wednesday 22nd of February 2023 01:12:07 PM)

Rating: 4.9 (rated by 37 users)

Compatible devices: 1747-OC Series, 193-DNENCAT, MSR41, 1791-16BC, 1756-M02AS, Compact 1769-OB32, 1734-IB8S, AADvance.

Recommended Documentation:

Text Version of Quick Start Manual

(Ocr-Read Summary of Contents of some pages of the Allen-Bradley 1336 PLUS II Document (Main Content), UPD: 22 February 2023)

  • 1, PE PE R (L1) TE S (L2) T (L3) U (T1) V (T2) W (T3) DC + DC – Dynamic Brake Required Input Fusing Required Branch Circuit Disconnect Shield Common Mode Core* Diagram shows connections that are common for all drives. Refer to User Manual for Detailed Information. Ground per Local Codes Motor Frame Motor Termi…

  • 2, Allen-Bradley 1336 PLUS II 1336 PLUS II Quick Start Guide 19 20 21 22 23 24 25 26 27 28 29 30 ! A hazard of personal injury from automatic restart exists with 2-wire control. 2-wire control uses maintained Run contacts that act as both Run (closed) and Stop (open) devices. Opening the Stop contact (terminal 20) will stop the dr…

  • 3, This start-up procedure covers only the most commonly adjusted values using the 1336 PLUS II “Startup” mode. Refer to the User Manual for detailed information. The following procedure is written for users who have a Human Interface Module (HIM) installed. For users without a HIM, respective external command…

  • 4, 1336 PLUS II Quick Start Guide ❑ 5. If Analog Option is installed, verify that DIP switch(es) are properly set (refer to Option Instruction Sheet). ATTENTION: In all of the following steps, rotation of the motor may occur. To guard against injury, incorrect rotation and possible equipment damage, read each step…

  • 5, 1336 PLUS II Quick Start Guide Process Display Power-Up Mode & Status Display ESC SEL or or or or OPERATOR LEVEL MODE LEVEL GROUP LEVEL Output Current (54) Output Voltage (1) Output Power (23) DC Bus Voltage (53) Output Freq (66) Freq Command (65) Anlg In 0 Freq (138) Anlg In 1 Freq (139) Anlg In 2 Fre…

  • 6, Allen-Bradley 1336 PLUS II Speed Control (77) PI Config (213) PI Status (214) PI Ref Select (215) PI Fdbk Select (216) PI Reference (217) PI Feedback (218) PI Error (219) PI Output (220) KI Process (221) KP Process (222) PI Neg Limit (223) PI Pos Limit (224) PI Preload (225) Rated Volts (147) Rated Amps (170) Rated kW (171) Firmware Ver. (…

  • Allen-Bradley 1336 PLUS II User Manual

  • Allen-Bradley 1336 PLUS II User Guide

  • Allen-Bradley 1336 PLUS II PDF Manual

  • Allen-Bradley 1336 PLUS II Owner’s Manuals

Recommended: ACU-140S, ZD-SI-601/ZD-SO-601, PIPELINER 11498

  • Emerson FISHER CV500

    www.Fisher.comD101640X012Design CV500 Rotary Control ValveContentsIntroduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Scope of Manual 1. . . . . . . . . . . . . . . . . . . . . . . . . Description 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications 2. . . . . …

    FISHER CV500 28

  • Wolf Link home

    WOLF GMBH / POSTFACH 1380 / D-84048 MAINBURG / TEL. +49.0. 87 51 74- 0 / FAX +49.0.87 51 74- 16 00 / www.WOLF.euDoc. no.: 3066086_201803 SubjecttomodicationsGBInstallationandoperatinginstructionsWOLF Link home / WOLF Link pro interface moduleWRS …

    Link home 12

  • Grosvenor RM-ICLSE-IT/RS

    IT31IT51Screw FixingsModule PositionReaderConnector3 Connect Module Fit the ribbon cable connector to the Front Panel observing polarising bump position. 4 Configure Terminal for Module Once hardware installation is complete power-up Terminal and if necessary configure Terminal — see over for details. 2 Screw Modu …

    RM-ICLSE-IT/RS 2

  • Kitz 150 SCTBZ Series

    Document No.：KE-1027-00 Operation Manual For Ｔwo Peace Type Steel Ball Valves 150/300SCTBZ,UTBZ （Flanged ends） Thank you for having chosen KITZ products. For safe and trouble-free function and …

    150 SCTBZ Series 32

Additional Information:

Operating Impressions, Questions and Answers:

Источник

Понравилась статья? Поделить с друзьями:
  • Alldent veneers инструкция по применению на русском
  • Alligator 434 mhz sst инструкция
  • All test на коронавирус инструкция по применению
  • Allerset таблетки турция инструкция по применению на русском языке
  • All purpose wine yeast beervingem инструкция