Casio W-211 / линейка Collection / модуль 3091 / год 2007
Инструкция к модулю Casio 3091
- Смотреть онлайн → (без скачивания, удобно на мобильных и планшетах);
- Скачать русскую инструкцию → (типичная “как у всех”, не всегда понятные картинки);
- Скачать английскую инструкцию → (детальная, много фото, более понятная).
Сложно настроить? Спрашивай на форуме Casio →
Читайте новости о любимых часах W-211 на блоге
[display-posts tag=”W-211″ posts_per_page=”4″]
Все новости о W-211 →
Побывайте на заводе Casio, изучайте последние новинки часов на Casioblog.RU
CASIO Модуль 2879/2889/3091
W-201/211, HDD-600
Руководство пользователя
Прежде всего прочтите эту важную информацию
Батарея
• В приобретенных вами часах батарея питания устанавливается на фабрике и
должна быть немедленно заменена при первых признаках недостаточности
питания (не включается подсветка, тусклый дисплей) у ближайшего к вам
дилера или дистрибьютора фирмы «CASIO».
Защита от воды
• Часы классифицируются по разрядам (с I по V) в соответствии со степенью
их защищенности от воды. Уточните разряд ваших часов с помощью
приведенной ниже таблицы, для правильной эксплуатации ваших часов.
Раз
ряд
Маркировка на
корпусе
Брызги,
дождь и т.п.
Плавание, мытье
машины и т.п.
Подводное
плавание,
ныряние и
т.п.
Ныряние
с
акваланг
ом
I —
Нет
Нет
Нет
Нет
II WATER
RESISTANT
Да
Нет
Нет
Нет
III 50M
WATER
RESISTANT
Да
Да
Нет
Нет
IV 100M
WATER
RESISTANT
Да
Да
Да
Нет
V 200M
WATER
RESISTANT
300M WATER
RESISTANT
Да
Да
Да
Да
Примечания для соответствующих разделов:
I. Часы не защищены от воды. Избегайте попадания любой влаги.
II. Не вытаскивайте коронку, если часы мокрые.
III. Не нажимайте кнопки часов под водой.
IV. Если часы подверглись воздействию соленой воды, то тщательно промойте
их и вытрите насухо.
V. Часы могут использоваться при погружении с аквалангом (за исключением
таких глубин, при которых требуется гелиево-кислородная смесь).
• Особенностью некоторых защищенных от воды часов является наличие у них
кожаных ремешков. Не надевайте эти часы во время плавания или какой-либо
другой деятельности, при которой ремешок погружается в воду.
Уход за вашими часами
• Никогда не пытайтесь вскрывать корпус и снимать заднюю крышку.
• Замена резиновой прокладки, защищающей часы от попадания воды и пыли,
должна осуществляться через каждые 2-3 года.
• Если внутрь часов попадет влага, то немедленно проверьте их у ближайшего
к вам дилера или дистрибьютора фирмы CASIO.
• Не подвергайте часы воздействию предельных температур.
• Хотя часы рассчитаны на использование их в обычных условиях, тем не
менее вы должны избегать грубого обращения с ними и не допускать их
падения.
• Не пристегивайте ремешок слишком сильно. Между вашим запястьем и
ремешком должен проходить палец.
• Для очистки часов и ремешка используйте сухую мягкую ткань, либо мягкую
ткань, смоченную в водном растворе мягкого нейтрального моющего
средства. Никогда не используйтесь легко испаряющимися средствами
(например такими, как бензин, растворители, распыляющиеся чистящие
средства и т.п.).
• Когда вы не пользуетесь вашими часами, храните их в сухом месте.
• Избегайте попадания на часы бензина, чистящих растворителей, аэрозолей из
распылителей, клеящих веществ, краски и т.п. Химические реакции,
вызываемые этими материалами, приводят к повреждению прокладок,
корпуса и полировки часов.
• Особенностью некоторых моделей часов является наличие на их ремешке
изображений, выполненных шелкографией. Будьте осторожны при чистке
таких ремешков, чтобы не испортить эти рисунки.
Для часов с пластмассовыми ремешками…
• Вы можете обнаружить белесое порошкообразное вещество на ремешке. Это
вещество не вредно для вашей кожи или одежды и может быть легко удалено
путем простого протирания куском ткани.
• Попадание на пластмассовый ремешок пота или влаги, а также хранение его в
условиях высокой влажности может привести к повреждению, разрыву или
растрескиванию ремешка. Для того, чтобы обеспечить длительный срок
службы пластмассового ремешка, при первой возможности протирайте его от
грязи и воды с помощью мягкой ткани.
Для часов с флуоресцентными корпусами и ремешками…
• Длительное облучение прямыми солнечным светом может привести к
постепенному исчезновению флуоресцентной окраски.
-
Инструкции по эксплуатации
1
Casio COLLECTION W-211-1A инструкция по эксплуатации
(4 страницы)
- Языки:Русский
-
Тип:
PDF -
Размер:
282.55 KB -
Описание:
Наручные часы
Просмотр
На NoDevice можно скачать инструкцию по эксплуатации для Casio COLLECTION W-211-1A. Руководство пользователя необходимо для ознакомления с правилами установки и эксплуатации Casio COLLECTION W-211-1A. Инструкции по использованию помогут правильно настроить Casio COLLECTION W-211-1A, исправить ошибки и выявить неполадки.
MA0702-EA
Operation Guide 2879/2889/3091
About This Manual
• The operational procedures for Modules 2879, 2889 and 3091 are identical. All of
the illustrations in this manual show Module 2879.
(Light)
Module 2879
• Button operations are indicated using the letters shown in the illustration.
• Each section of this manual provides you with the information you need to perform
operations in each mode. Further details and technical information can be found in
the «Reference» section.
General Guide
• Press B to change from mode to mode.
• In any mode, press L to illuminate the display.
Timekeeping Mode
Timekeeping
PM indicator
Day of week
Month – Day
Seconds
Hour : Minutes
3. When the setting you want to change is flashing, press C to change it as
described below.
To change this setting
Seconds
Hour, Minutes, Year, Month,
Day, Day of week
• Pressing C while the seconds are in the range of 30 to 59 resets them to 00 and
adds 1 to the minutes. In the range of 00 to 29, the minutes are unchanged.
4. Press A to exit the setting screen.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press C to toggle between 12-hour timekeeping and
24-hour timekeeping.
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59. 24-hour
format is displayed as 24 on the Module 2879 and 3091 display, and 24H on the
Module 2889 display.
• The P and 24-hour format (24, 24H) indicators are not displayed with the
Timekeeping Mode time on the Alarm Mode and Dual Time Mode screens.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
Alarm
Timekeeping Mode time
(Hour : Minutes)
Mode indicator
Alarm time
(Hour : Minutes)
(Light)
Module 2889
Module 3091
Alarm Mode
Press
.
Use the Timekeeping Mode to set and view the current
time and date.
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press B to move the flashing in the sequence shown
below to select other settings.
Seconds
Hour
Day of week
Day
Month
Perform this button operation
Press C to reset to 00.
Press C to increase the setting.
Holding down C changes the setting at high speed.
When the daily alarm is turned on, the alarm tone sounds
when the alarm time is reached.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds,
regardless of the mode the watch is in.
(Light)
Stopwatch Mode
To set an alarm time
Minutes
To stop the alarm tone after it starts to sound
Press any button.
Year
To turn the Daily Alarm and Hourly Time Signal on and off
Hourly time signal
on indicator
Alarm on indicator
To test the alarm
In the Alarm Mode, hold down C to sound the alarm.
Stopwatch
Mode indicator
1/100 second
Minutes
Hours
Seconds
To measure times with the stopwatch
Elapsed time
Start
Split time
Start
Two Finishes
Start
Dual Time Mode
1. In the Alarm Mode, hold down A until the hour setting
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
2. Press B to move the flashing between the hour and
minutes.
3. While a setting is flashing, use C to increase it.
Holding down C changes the setting at high speed.
• With the 12-hour format, set the time correctly as a.m.
(no indicator) or p.m. (P indicator).
4. Press A to exit the setting screen.
In the Alarm Mode, press C to cycle through the on and
off settings as shown below.
Alarm On Indicator/Hourly Time Signal On Indicator
Both on
Both off
Daily alarm
only
• The alarm on (ALM) indicator flashes while the alarm is
sounding.
• The alarm on (ALM) indicator and Hourly Time Signal
on (SIG) indicator are displayed in all modes.
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing B.
Stop
Re-start
Stop
Split
Split release
Stop
(SPL displayed)
Split
Stop
Split release
First runner
Second runner
Display time of
finishes.
finishes.
second runner.
Display time of
first runner.
Hourly Time
Signal only
Clear
Clear
Clear
1
1
Operation Guide 2879/2889/3091
MA0702-EA
About This Manual
• The operational procedures for Modules 2879, 2889 and 3091 are identical. All of
the illustrations in this manual show Module 2879.
Module 2889
(Light)
Module 2879
(Light)
Module 3091
(Light)
• Button operations are indicated using the letters shown in the illustration.
• Each section of this manual provides you with the information you need to perform
operations in each mode. Further details and technical information can be found in
the “Reference” section.
Timekeeping Mode
Alarm Mode
Stopwatch Mode
Dual Time Mode
Press .
General Guide
• Press B to change from mode to mode.
• In any mode, press L to illuminate the display.
Day of week
Seconds
Hour : Minutes
PM indicator
Month – Day
Timekeeping
Use the Timekeeping Mode to set and view the current
time and date.
To set the time and date
1. In the Timekeeping Mode, hold down A until the
seconds start to flash, which indicates the setting
screen.
2. Press B to move the flashing in the sequence shown
below to select other settings.
Seconds Hour
Minutes
YearMonthDay of week Day
3. When the setting you want to change is flashing, press C to change it as
described below.
To change this setting
Seconds
Hour, Minutes, Year, Month,
Day, Day of week
Perform this button operation
Press C to reset to 00.
Press C to increase the setting.
Holding down C changes the setting at high speed.
• Pressing C while the seconds are in the range of 30 to 59 resets them to 00 and
adds 1 to the minutes. In the range of 00 to 29, the minutes are unchanged.
4. Press A to exit the setting screen.
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced.
To toggle between 12-hour and 24-hour timekeeping
In the Timekeeping Mode, press C to toggle between 12-hour timekeeping and
24-hour timekeeping.
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59. 24-hour
format is displayed as 24 on the Module 2879 and 3091 display, and 24H on the
Module 2889 display.
• The P and 24-hour format (24, 24H) indicators are not displayed with the
Timekeeping Mode time on the Alarm Mode and Dual Time Mode screens.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
Alarm time
(Hour : Minutes)
Timekeeping Mode tim
(Hour : Minutes)
Mode indicator
Alarm
When the daily alarm is turned on, the alarm tone sounds
when the alarm time is reached.
You can also turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing B.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds,
regardless of the mode the watch is in.
Hourly time signal
on indicator
Alarm on indicator
To set an alarm time
1. In the Alarm Mode, hold down A until the hour setting
starts to flash, which indicates the setting screen.
• This operation automatically turns on the alarm.
2. Press B to move the flashing between the hour and
minutes.
3. While a setting is flashing, use C to increase it.
Holding down C changes the setting at high speed.
• With the 12-hour format, set the time correctly as a.m.
(no indicator) or p.m. (P indicator).
4. Press A to exit the setting screen.
To stop the alarm tone after it starts to sound
Press any button.
To turn the Daily Alarm and Hourly Time Signal on and off
In the Alarm Mode, press C to cycle through the on and
off settings as shown below.
Alarm On Indicator/Hourly Time Signal On Indicator
Daily alarm
only
Both off
Both on Hourly Time
Signal only
• The alarm on (ALM) indicator flashes while the alarm is
sounding.
• The alarm on (ALM) indicator and Hourly Time Signal
on (SIG) indicator are displayed in all modes.
To test the alarm
In the Alarm Mode, hold down C to sound the alarm.
Minutes
1/100 second
Mode indicator
Hours
Seconds
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restarting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
if you exit the Stopwatch Mode.
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing B.
To measure times with the stopwatch
Elapsed time
Start Stop Re-start Stop Clear
Start
Split
(SPL displayed)
Split release Stop Clear
Start
Split Stop Split release Clear
Split time
Two Finishes
First runner
finishes.
Display time of
first runner.
Second runner
finishes.
Display time of
second runner.