Devo f7 инструкция на русском языке

Walkera DEVOF7

Передатчик Walkera Devo F7 — это семи-канальный пульт для дистанционного управления различными моделями планеров, самолетов и вертолетов с возможностью «смотреть их глазами».

Quick Links

• Page 1
  DEVO-7 Page 1 of 170…

• Page 2: Table Of Contents

  NSTALLATION REQUIREMENT FOR RECEIVER 12.0 I …………21 NSTALLATION REQUIREMENT FOR ATTERY PACK 12. 1 DEVO-7 Battery Charging …………….22 PART TWO: HELICOPTER ………………..23 ……………………. 23 YSTEM MENU 1.1 (DISPL) 1.1 Display ………………… 23 1.2 (Buzzer Setting) ………………..24 （…

• Page 3
  2.6TYPE OPTION …………………. 96 2.7 Trim system………………….97 2.9 Device Output …………………. 99 （ ） 2.10 WING ………………….102 1.7 Power amplifier ………………..106 （ ） 2.12 FIXID ………………….107 3.0 F …………………. 109 UNCTION DEVO-7 Page 3 of 170…
• Page 4
  3.15 Aileron to flap mix ……………….. 148 3.16(PRGMX) ………………….152 （ ） 3.17 MONIT ………………….. 161 （ ） 3.18 Fail -Safe ………………..162 （ ） 3.19 TRAIN ………………….163 3 .20（TIMER） ………………….166 PART FOUR: UPGRADE INTERFACE …………… 168 DEVO-7 Page 4 of 170…

• Page 5: Users Manual Of Devo-7

  Part one:General information 1.0 Foreword DEVO-7 adopts 2.4 GHz Direct Sequence Spread Spectrum (DSSS) technology and features automatic ID binding, automatic ID assignment, and also features fixed ID set by you yourself. The usage of wireless copy function keeps you away from the trouble in wire link-up.

• Page 6: Satety Needing Attention

  When turning off the helicopter， disconnect the battery first， and turn off your transmitter later. An upset in the order of connection may cause your helicopter out of control. Please form a correct habit of turn-on and turn-off. DEVO-7 Page 6 of 170…

• Page 7: Features

  10) DEVO-7 can be freely switched among Modes 1， 2，3 ,and 4. 11) DEVO-7 is suitable for helicopter and airplane. In the helicopter mode，there are 3 flight modes ， each of which can be freely set and its parameters can be personalizedly adjusted to meet the requirement for F3C or 3D aerobatic flight.

• Page 8: Specification

  Current drain ….≤230mA (100mW) Power supply ….5# Battery 8X1.5V or NiMH 8X1.2V1600-2000mAh Output pulse: 1000—2000Ms（1500 Neutral） 3.2 Receiver Specification： Type: 2.4GHz 7 channels Sensitivity:- 105dbm Frequency Interval: ≥ 4M Weight: 11.6g Dimension: 43X28X16mm Receiver Battery: 4.8-6V1300mAh DEVO-7 Page 8 of 170…

• Page 9: Radio Cover Identification

  4.0 Radio Cover Identification 4.1 Face Cover Indicator Diagram DEVO-7 Page 9 of 170…

• Page 10: Back Cover Indicator Diagram

  3.Digital Signal Converter socket (DSC): used for simulator flight practice via computer (You need a software and its dongle which are available in hobby shops)， and for training. 4. Battery Pack Cover 5. Charge socket (CHG): input DC at 12V, Current 50MAH； Polarity: DEVO-7 Page 10 of 170…

• Page 11: Wiring Diagram

  4.3 Wiring Diagram 4.4 Function keys in panel There are 6 functional keys in the panel of DEVO-7. Below are the details: EXT： Reset key,Press EXT to exit the main menu. ENT： Confirmation key. Press ENT to access the system or the function mode.

• Page 12: Stick Length Ajustment

  Find the inside structure of the left and right throttle stick as below. Use the cross screw driver adjust the screw F and G, clockwise will tighten the crew while counterclockwise will loosen the screw; Cover the base plate after accomplishment. DEVO-7 Page 12 of 170…

• Page 13: Neck Strap Usage

  There are total four stick modes from MODE 1 through MODE 4. The left-hand throttle includes MODE 1 and MODE 3, and the right-hand throttle includes MODE 2 and MODE 4. Below is the sketch map: DEVO-7 Page 13 of 170…

• Page 14: Switches Between Left — Hand And Right — Hand Throttles

  MODE 1 and MODE3 are listed in right-hand throttle. 8.0 Switches between left-hand and right-hand throttles The throttle switch between the left hand and right hand will be successful if both the MECHANICAL switch and ELECTRONIC switch are finished, separately. Below are DEVO-7 Page 14 of 170…

• Page 15: Right Throttle Switch To Left Throttle

  MECHANICAL and ELECTRONIC switches changed, respectively. And the transmitter is ready to normally work now. 8.2 Left Throttle Switch To Right Throttle 1）MECHANICAL switch Refer to the above steps of “MECHANICAL switch”, open the base plate DEVO-7 Page 15 of 170…

• Page 16: Training Function

  Two DEVO-7 transmitters working together can execute the training function to meet the requirements for the beginner. The setting method is shown as below: 1）Data copy First, use the wireless copy function between two DEVO-7 to copy the main DEVO-7 Page 16 of 170…

• Page 17
  DEVO-7 bind with the assigned model, fly it normally. Then turn off the power Insert the other end of the digital signal wire into the trainer’s DEVO-7, and then turn on its power. A linkage icon will be shown as below: 3）…
• Page 18
  If the trainer push back TRN switch, it means the trainer has recycle the operate control from the trainee and the transmiter was operate by the trainer. DEVO-7 Page 18 of 170…

• Page 19: Customized Fixed Id

  After setting, press ENT, it will come out “RUN” interface. Press R or L to change ON to YES,press ENT to make ID binding, it will automatically back to model menu after accomplishment. DEVO-7 Page 19 of 170…

• Page 20: Installation Requirement For Receiver

  If come to the following image, press R or L , turn ON to OFF, press EXT to exit. 11.0 Installation requirement for receiver / It is important to correctly mount your radio system in your model. Below are DEVO-7 Page 20 of 170…

• Page 21: Installation Requirement For Battery Pack

  AA battery or the same size full charged 8 cells NIMH battery into the battery box. Please check again to make sure the polarities are correct. Warning: Do not put the polarities of batteries in the opposite directions. DEVO-7 Page 21 of 170…

• Page 22: Devo-7 Battery Charging

  12. 1 DEVO-7 Battery Charging Warning: the CHG socket is only used for the rechargeable NIMH batteries. If using the batteries which is unchargeable. The CHG socket is not allowed to use. Charge socket (CHG): input DC at 12V, 50mA； Polarity:…

• Page 23: Part Two: Helicopter

  Part two: Helicopter System menu All the functional settings, which are relative to the operation system of DEVO-7 itself, integrated in System Menu. They include Display, Buzzer, Stick Mode, FULLY Stick & Lever, and About. Below is the boot screen of helicopter: 1.1 Display…

• Page 24: Buzzer Setting)

  UP and DN keys until “SBUZZE” becomes flashing, then press “ENT” key to the STATE setting menu. Press R or L until the flashing characters to be ON or OFF, ON is to set the Buzzer as active; while OFF is to set it as inhabit. DEVO-7 Page 24 of 170…

• Page 25
  After finishing the above setting, press DN key until getting TONE setting menu. Press R or L key to change the flashing characters to numbers like 1-10. Press EXT key to exist after finished. DEVO-7 Page 25 of 170…

• Page 26: Stmod

  Setting: (STMOD) Stick Mode: press “ENT” key to get the flashing main memu. Press UP and DN keys until “STMOD” becomes flashing, then press “ENT” key to the Stick Mode setting menu. Press R or L to select the required stick mode until it becomes DEVO-7 Page 26 of 170…

• Page 27: Calib

  When you get the below interface after pressed ENT key, it shows the calibration is successful. DEVO-7 Page 27 of 170…

• Page 28: About)

  “ENT” key to get the flashing main memu. Press UP and DN keys until “SYSTEM” becomes flashing, then press “ENT” key to system setting menu. Press UP or DN key until “SOFT” becomes flashing; Press ENT key, you will find the version information under the SOFT interface. DEVO-7 Page 28 of 170…

• Page 29: Model Menu)

  Press EXT to exist after finished. 2.0(Model Menu) Model Menu manages all the model data saved in DEVO-7. It includes Model Select, Model Name, Model Copy, Model Transmit, Model Receive, Model Reset, Type Select, Trim System, Device Select, Device Output, Swash Type, Power Amplifier and Fixed 2.1（Model select）…

• Page 30: Model Name

  , then Press “ENT” key to enter Model Menu; Press UP or DN until “copy” becomes flash and then press “ENT” button to get the Model name options.Press R or L can change the selected model. DEVO-7 Page 30 of 170…

• Page 31: Model Wireless Copy

  Press R or L to select YES for reset or NO for Cancel. Press ENT to copy and EXT to exit. 2.4 Model wireless copy The model data between two DEVO-7 equipments can be wirelessly copied via Model Transmit and Model Receive in Model Menu 1) Model transmission Press “ENT”…

• Page 32
  The enquiry interface of whether to transmit will be shown after press ENT. Press R or L to select YES for Receiving or NO for Cancel. Choose YES for receiving,then press ENT “Connecting ……”interface will be shown. DEVO-7 Page 32 of 170…

• Page 33: Reset

  Press “ENT” key to enter Model Menu; Press UP or DN button until “RESET” becomes flash；Press “ENT” key,there are There are batch reset and single reset selections. Press R or L to choose ALL or other models. DEVO-7 Page 33 of 170…

• Page 34: Type

  Press “ENT” key to enter Model Menu; Press UP or DN button until “TYPE” becomes flash； Press “ENT” key to get helicopter and Aeroplane selections. Press R or L button until selected model becomes flash, Press ENT button to confirm, then press EXT to exit. DEVO-7 Page 34 of 170…

• Page 35: Step

  “Normal” means the trim is always working although the corresponding stick stays anywhere. “Limited” means the trim is out of working when the corresponding stick is at maximum position. Press EXT to exit after setting. DEVO-7 Page 35 of 170…

• Page 36: Device Select

  Setting:After the setting 2),below interface will be shown after press DN.Press R or L to choose Common(COMM) and Flight Mode(FMOD). 3）Throttle Hold Switch Throttle Hold switch including Gear Switch,hold Switch,D/R switch,MIX2,MIX12, FMD2,FMD12.Factory default setting is HOLD switch. DEVO-7 Page 36 of 170…

• Page 37: Device Output

  D/R, HOLD,TRN and AUX2. The default setting is GEAR SW. Press DN can enter the interface of Gear activate, inhibit or use other functions. 2)Press R or L can change activate, inhibit or use other functions which includes INH,ACT and GYRO. DEVO-7 Page 37 of 170…

• Page 38
  Press DN can enter the interface of AUX2 activate, inhibit or use other functions. Press R or L can change activate, inhibit or use other functions which includes INH,ACT,GYRO and GOV(governor). Press EXT to exit. DEVO-7 Page 38 of 170…

• Page 39: Swash Type

  Press EXT to exit. 2.11（AMPLI） The transmission output power of DEVO-7 is adjustable. It is divided into six grades from small to big. The lower the transmission output power transmits, the shorter the radio range is, and the longer the stand-by time will be. The higher the transmission output power, the farer the radio range, and the shorter the stand-by time.

• Page 40: Fixed Id

  2.12 Fixed ID This setting will bind DEVO-7 and its receiver in a unique corresponding relationship. It will greatly speed up the time of automatic binding when DEVO-8 powered on. Setting for fixed ID The setting for fixed ID should be under the status that automatic ID binding is successfully finished.

• Page 41: Function Menu

  The red light of receiver will flash slowly. This means the fixed ID code has been cancelled. Pull out BIND PLUG. DEVO-7 also needs to make relative cancellation and reversion after the fixed ID in receiver is cleared out.

• Page 42: Reverse Switch

  AILE, THRO, RUDD, GEAR, PITCH, GYRO and so on. The setting are the same as above, here we take the ELEV as example. EXT it for finish. DEVO-7 Page 42 of 170…

• Page 43: Sub Trim)

  GYRO and so on. The setting are the same as above, here we take the ELEV for example. Every channel default value is 0.0%. Adjust ranges as below: Adjustment Channel name Channel name Adjustment range range Elevator D62.5%-U62.5% Gear -62.5%- +62.5% Aileron R62.5%-L62.5% Pitch L62.5%- H62.5% Throttle L62.5%-H62.5% Gyro -62.5%- +62.5% DEVO-7 Page 43 of 170…

• Page 44: Dual Rate And Exponential

  The picture as below: 2) Position selection Press DN to enter Switch Position setting in the above Picture, there are POS0,POS2,POS3. Press R or L, it is possible to choose POS0,POS1,POS2,POS3. The D/P Switch Position on transmitter DEVO-7 Page 44 of 170…

• Page 45
  After setup the position, press DN to enter D/R enactment interface, press R/L to adjust D/R value. 4) Exponential adjustment After setup the Dual Rate, Press DN to enter EXP setting interface, there are Line and adjustable value, 2 setting options. Press R or L to choose. DEVO-7 Page 45 of 170…
• Page 46
  Hold ) in “Throttle Hold”, under “Function Menu”. After setup the Exponential adjustment, press DN to enter NORM setting interface, Press R or L to flash “SWITC” (switch), there are opions for POS0,POS1,POS3,POS3. Press R or L to bink the desired option. DEVO-7 Page 46 of 170…
• Page 47
  After setup ST1 mode, Press DN to enter ST2 setting interface, the setting method as above. If the Throttle Hold is activated, it appears Throttle Hold option as below, After setting ST2 Mode, Press DN to enter THHLD setting interface, the setting method as above. DEVO-7 Page 47 of 170…

• Page 48: Throttle Hold

  “Throttle Hold Position” setting Throttle Hold is activated, press DN to enter the interface as below: Press R or L to change the Hold value. The minimum value is -20.0%; The maximum value is +50.0%. DEVO-7 Page 48 of 170…

• Page 49: Throttle Curve

  ENT to enter the interface of Servo Hold State, Press R or L to choose YES or NO. Press ENT to confim. Flight Model options will be shown in the interface, there are NORM, ST1, ST2. DEVO-7 Page 49 of 170…

• Page 50
  Press DN, the 7 piont options will be shown, then press R or L to choose one of 7 points, There are L、1、2、3、M、4、5、H for option. Press DN button, the output can be set and then press R or L to set the output amount. DEVO-7 Page 50 of 170…

• Page 51: Mix To Throttle

  In above interface, Press ENT to enter Switch options and Switch state. There are Switch options including ALLON (always on), NOR (normal mode), ST1(stunt 1), ST2(stunt2),Gear. ALLON(always on) option: It will be default always on if NOR (normal mode) or DEVO-7 Page 51 of 170…

• Page 52
  After setting NOR(normal mode) option, press DN to enter ST1 (stunt1) switch setting interface, press R or L to set switch activated or inhibited. After setting ST1(stunt1) option, press DN to enter ST2 (stunt2) switch setting interface, press R or L to set switch activated or inhibited. DEVO-7 Page 52 of 170…
• Page 53
  After setting ST2(stunt2) option, press DN to enter GEAR switch setting interface, press R or L to set switch activated or inhibited. 3)UP setting After Switch option setting finished, press EXT to back Switch Option, the picture as below: DEVO-7 Page 53 of 170…
• Page 54
  1) Please make sure the above setting value for Mix & Throttle is good for ideal flight and the action in various flight modes are normal. 2) The function is in spare when governor is working. DEVO-7 Page 54 of 170…

• Page 55: Gyro Setting

  50.0%. The bigger the amount is, the bigger the gyro sensor gain becomes. If the value less than 50,it’s NOR mode. The smaller the amount is, the bigger the gyro sensor gain becomes. DEVO-7 Page 55 of 170…

• Page 56
  50.0%. The bigger the amount is, the bigger the gyro sensor gain becomes. If the value less than 50, it is NOR mode. The smaller the amount is, the bigger the gyro sensor gain becomes. DEVO-7 Page 56 of 170…

• Page 57: Governor

  There are “Normal mode”,”ST1”,“ST2”, “Throttle Hold” 4 options available. NORM setting: The picture as below. Press R or L to set the value. Press R to decrease, the minimum is -125%; Press L to increase, the maximum is +125%. DEVO-7 Page 57 of 170…

• Page 58
  THHLD setting: Throttle Hold should be activated. After setup the ST2 option, press DN to enter THHLD setting interface. Press R or L to set the value. Press R to decrease, the minimum is -125%; Press L to increase, the maximum is +125%. DEVO-7 Page 58 of 170…

• Page 59: Swash Mix

  Press R button to reduce the mix and L button to increase. If the mix directions are opposite, it is the plus or minus sign before possible to reverse mix direction through R or L button to change ±125% amount. The adjustable range is DEVO-7 Page 59 of 170…

• Page 60
  Setting Method: After PITCH mix setting complete, press DN button to get into EXP setting interface. Press R or L button to get “ON” and “OFF” options. The default setting is “OFF”, but it is suggested to be “ON”. DEVO-7 Page 60 of 170…

• Page 61: Pitch Curve

  The curve of each flight mode can be set respectively. Press R or L button to choose the required flight model. Press DN button to get the EXP ON or OFF option. Press R or L button to choose ON or OFF. DEVO-7 Page 61 of 170…

• Page 62
  2, M, 4, 5 and H7. Press DN key, the output can be set and then press R or L to set the amount. Press UP to return, and continue to set other points. Press EXIT after the settings. The basic examples are only for your reference. Adjustment to the real flights is a must. Normal DEVO-7 Page 62 of 170…
• Page 63
  Flight Mode: Normal Throttle Curve Pitch Curve Flight Mode 1 Throttle Curve Pitch Curve Flight Mode 2 DEVO-7 Page 63 of 170…
• Page 64
  Autorotation Landing DEVO-7 Page 64 of 170…

• Page 65: Program Mix

  Press ENT button then expand an enquiry “All Servos Hold?” Press R or L to choose YES or NO. If “YES” selected, all the servos will be locked in the current status, if “NO” selected, all servos are unlocked. DEVO-7 Page 65 of 170…

• Page 66
  2) Setting of slave channel: after the setting of main channel finished, press DN button. When getting to below interface, choose the required slave channel among ELEV, AILE, THRO, RUDD, GEAR, PITCH and GYRO. 3) Setting of Gain: Take Elevator as main channel as an example. Press DN button DEVO-7 Page 66 of 170…
• Page 67
  Gain Setting Interface. Press R to decrease the mix amount and L to increase. It is possible to reverse mix direction through changing the plus or minus sign before amount. The adjustable range is ±100%. DEVO-7 Page 67 of 170…
• Page 68
  ALLON ( always on): if normal mode switch, ST 1 switch, ST 2 switch, D/R switch, HOLD switch and GEAR switch are all active, then this switch is inhibited. The default setting is ALL ON. DEVO-7 Page 68 of 170…
• Page 69
  After setting ST 1 ( Stunt flight 1 ), press DN button to get to ST 2 ( Stunt flight 2 ) switch setting interface. Press R or L to set the switch inhibited or active. DEVO-7 Page 69 of 170…
• Page 70
  Press R or L to set the switch inhibited or active. After setting D/R, press DN button to get to HOLD switch setting interface. Press R or L to set the switch inhibited or active. DEVO-7 Page 70 of 170…
• Page 71
  UP or DN to flash “PRGMX”. and press ENT to program mix setting and current status (default setting is “inhabit”) interface. Press R or L to choose inhibited, normal or curve. Take “program mix 1” for axample, and choose “curve” setting. DEVO-7 Page 71 of 170…
• Page 72
  OAILE, OPITC, ORUDD, PELEV, PAILE, PTHRO, PRUDD and FMOD。 2) Setting of slave channel: after the setting of main channel finished, press DN button. When getting to below interface, choose the required slave channel among ELEV, AILE, THRO, RUDD, GEAR, PITCH and GYRO. DEVO-7 Page 72 of 170…
• Page 73
  “ or “ OFF”. The pitch curve will be smoothly changed if choosing On. Otherwise choosing Off. 4) Point setting: Press DN, the 7 piont options will be shown. Press R or L to select any point from L, 1, 2, M, 4, 5 and H7. DEVO-7 Page 73 of 170…
• Page 74
  Press ENT button to get the switch setting including ALLON, normal mode switch, ST 1 switch, ST 2 switch, D/R switch, HOLD switch and GEAR switch. DEVO-7 Page 74 of 170…
• Page 75
  Press R or L to set the switch inhibited or active. After setting NOR (normal flight), press DN button to get to ST 1 (stunt flight 1) switch setting interface. Press R or L to set the switch inhibited or active. DEVO-7 Page 75 of 170…
• Page 76
  Press R or L to set the switch inhibited or active. After setting ST 2 (stunt flight 2), press DN button to get to D/R switch setting interface. Press R or L to set the switch inhibited or active. DEVO-7 Page 76 of 170…
• Page 77
  After setting D/R switch, press DN button to get to HOLD setting interface. Press R or L to set the switch inhibited or active. After setting HOLD switch, press DN button to get to GEAR setting interface. Press R or L to set the switch inhibited or active. DEVO-7 Page 77 of 170…

• Page 78: Monit) Monitor

  “MONIT”becomes flash. Press ENT button to get the name of ELEV channel and output display. Press R or L to check other channels’ name and output. channel name Output display After finished, press EXT to exist. DEVO-7 Page 78 of 170…

• Page 79: Fail Safe

  On above interface,press R or L to selet keep or fail safe. If selecting keeping,locking the last dated received; If selecting fail safe, to execute the pre-set date which is pre-set. The default setting is Servo Hold Press R to SAFE,press DN to enter fail safe date interface DEVO-7 Page 79 of 170…

• Page 80: Train

  The setting method is shown as below: 1）Data copy Using the wireless copy function of the two DEVO-7 transmitter, the model saved in the trainer’s transmitter can be transmitted to the trainee’s to ensure the model parameters are exactly same.

• Page 81
  Press UP or DN,select controlled channel,press R or L to change channel controlled right, INT for forbidden; ACT for granting. Press EXT to exit after finishing setting. 4）usage method The training switch should be worked with HOLD/TRN,as following DEVO-7 Page 81 of 170…

• Page 82: Timer

  If trainer move away TRN, that means trainer will get back the operated right from trainee and operate the model. 3.16（TIMER） There are two timers which can be set shopwatch and countdown,respectively.Each timer can be operated by switch. DEVO-7 Page 82 of 170…

• Page 83
  Stopwatch setting, the following interface for stopwatch,press EXT to exit The max range of stopwatch is from 0 to 59 min 59 sec A:Countdown setting: press R or L on press the above interface to select counterdown setting as following; DEVO-7 Page 83 of 170…
• Page 84
  Press R or L to set countdown. The countdown rang of is from00:05-59:55. C:usage Press UP on “ on” interface AN to start on the first time,repress UP to stop; press DN,timer is the orginal 0 stopwatch interface coundown interface DEVO-7 Page 84 of 170…

• Page 85: Part Three: Airplane

  The related functions of Devo 7 are integrated to SYSTEM MENU, including DISPLAY, BUZZE, STICK MODE, STICK CALIBRATION and ABOUT. The boot screen of airplane is shown as below: 1.1 (DISPL) 1 ） Backlight brightness: the backlight brightness can be adjusted. The power DEVO-7 Page 85 of 170…

• Page 86: Buzzer Warning

  Press UP or DN to get twinkling “SBUZZE”, and press ENT to enter STATE menu. Press R or L to make twinkling figure turn into ON or OFF. On means active, OFF means inhibitive. DEVO-7 Page 86 of 170…

• Page 87
  3）Buzzer tone: the tone is composed of 10 grades. You can choose the favorite tone according to your interests and make a listening test. After above setup, Press DN to get TONE setup interface, then Press R or L to confirm the tone grade you want. DEVO-7 Page 87 of 170…

• Page 88: Stick Mode

  MODE 1 and MODE 3, Left-hand throttle include MODE 2 and MODE 4. Please see below picture. MODE 2 and MODE 4 are listed in left-hand throttle. Stick Mode setup: Press ENT key in main interface and it will appears twinkling main DEVO-7 Page 88 of 170…

• Page 89: Calibration

  If shows below interface after press EXT, it means calibration is finished. DEVO-7 Page 89 of 170…

• Page 90: About)

  “DN” to get a twinklyng “SYSTEM”, And then press “ENT to enter system menu. Press “UP” or “DN” to get twinklyng “ . And then press “ENT” to get SOFT ABOUT” interface, you can check the versions of hardware and software. DEVO-7 Page 90 of 170…

• Page 91: Model Menu)

  Press EXT to exit after finish. 2.0(Model Menu) Model Menu manages all the model data saved in DEVO-7. It includes Model Select, Model Name, Model Copy, Model Transmit, Model Receive, Model Reset, Type Select, Trim System, Stick Position, Warning, Device Select, Device Output, Wing Type and Fixed ID.

• Page 92: Model Name

  Press ENT to show model you want to change, and press ENT, the inquiring interface will be shown. Press R or L to choose ON or YES, and then press YES to copy, press NO to give up. DEVO-7 Page 92 of 170…

• Page 93: Model Wireless Copy

  Press R or L to choose model After choose the model to transfer, please press ENT to enter inquiring interface. Press R or L to choose ON or YES, press YES to copy and press NO to give up. DEVO-7 Page 93 of 170…

• Page 94
  Press R or L to choose ON or YES, and choose YES to receiver, choose NO to give up. Choose YES to receive, and press ENT to show model connecting interface… DEVO-7 Page 94 of 170…

• Page 95: Model Reset

  ENT to enter model menu. Press UP or DN to flash RESET, press ENT to enter item for option. There are WHOLE RESET or UNIQUE RESET for option. Press R or L to choose item need to reset. DEVO-7 Page 95 of 170…

• Page 96: Type Option

  ENT to enter into model menu. Press UP or DN to flash TYPE, and press ENT. There are helicopter and airplane for option, press R or L to flash the item be chosen. Press EXT after finish DEVO-7 Page 96 of 170…

• Page 97: Trim System

  Press R or L to select Normal and Limited,once finished, press EXT to exit. 2.8 Device select This setting can help you configure various functional switches, or adjust levers. It DEVO-7 Page 97 of 170…

• Page 98
  In Flight Mode, the trim value, which each stick is corresponding to, puts independently effect on the corresponding stick. The factory default is Common. Settings: once finished the step2 , press DN to appear below interface,press R or L to select COMM or FMOD DEVO-7 Page 98 of 170…

• Page 99: Device Output

  Device output can set up the output switches and select the usage of levers, respectively. It can also activate, inhibit or use other functions. Setting method: Press ENT in the main interface, main menu will be blinking, press UP or DN to DEVO-7 Page 99 of 170…

• Page 100
  2）FLAP After set the GEAR , press DN to enter the FLAP setting, see belows, press R or L to change select FLAP SW or BUTTON option,there are FMD MIX D/R、HOLD、GEAR、 TRN、AUX2 and so on DEVO-7 Page 100 of 170…
• Page 101
  AUX2 SW or BUTTON option,there are FMD MIX D/R、HOLD、GEAR、 TRN、AUX2 and so on .The default setting is FMOD. Press DN to enter AUX2 ACT,INHIBIT and other functions options, Press R or L to change select enabled,,forbiden and other functions options,there are INH、ACT、GYRO。 DEVO-7 Page 101 of 170…

• Page 102: Wing

  Press ENT in the main interface to appear blinking main menu, press UP or DN to appear blinking “MODEL”, press ENT to enter model menu, press UP or DN to appear blinking”WING”, press ENT to ehter wing type interface , see belows. DEVO-7 Page 102 of 170…

• Page 103
  1.1) Flaperon Below is the graphics for the servos location of the Flap and Aileron 1.2）DELTA Below is the graphics of the servos location of the Delta Type. connects to the ELEVRON channel in Receiver DEVO-7 Page 103 of 170…
• Page 104
  ELEVATOR channel in Receiver Left elevator connects to the RUDDER channel in Receiver Right elevator 3)Dual channels setting Dual Channels can be set as Elevator, Aileron, Rudder, or Flaperon. It is of dual DEVO-7 Page 104 of 170…
• Page 105
  C: Select “DLETA”option in the wing type selection,,V-TAIL is inhibit option , the channel setting options including Rudder, and Flap. Select “Nor”options in the wing type selection,,V-TAIL can not be ACT 3.2）sub dual channel settings DEVO-7 Page 105 of 170…

• Page 106: Power Amplifier

  Press R or L ,,there are Inhibit and the channel that has been forbiden in the 2.9 device output menu,select the desired setting channel and make blinking ,if channel has been occupied,the setting will not appear. 1.7 Power amplifier DEVO-7 Page 106 of 170…

• Page 107: Fixid

  The transmission output power of DEVO-7 is adjustable. It is divided into six grades from small to big. The lower the transmission output power transmits, the shorter the radio range is, and the longer the stand-by time will be. The higher the transmission output power, the farer the radio range, and the shorter the stand-by time.

• Page 108
  Insert the assorted BIND PLUG into the output terminal of BATT before the receiver is powered on, and then plug 5V DC power into other output terminal. The red light of receiver will flash slowly. This means the fixed ID code has been cancelled. Pull out BIND PLUG. DEVO-7 Page 108 of 170…

• Page 109: Function Menu

  “ENT” to enter Function Menu; Press UP or DN to flash “REVSW”; Press ENT, The options for Channel Name and flashing Reverse Switch will be shown. Press R or L to change NOR or REV state. Press DN, there are Reverse Switches in DEVO-7 Page 109 of 170…

• Page 110: Travel Adjust

  ENT to enter Function Menu; Press UP or DN to flash “SUBTR”; Press ENT to enter the options for Channel names and flashing neutral point value. It is possible to change the neutral point setting value through R or L button,if the direction DEVO-7 Page 110 of 170…

• Page 111: Dual Rate And Exponiential

  125%. Under the help with exponential curve adjustment, it is possible to make both customized settings and automatic settings. The switch between Dual Rate and Exponential can be performed via pushing or pulling the Flight Mode lever. DEVO-7 Page 111 of 170…

• Page 112
  Press R or L, the switch will be taken place among POS0, POS1 and POS2 D/R switch postion on Radio 3） Dual Rate adjustment After your POSTION setting, press DN to show D/R interface, press R or L to set D/R value. DEVO-7 Page 112 of 170…
• Page 113
  SWITCH under DEVICE SELECTION in MODEL MENU is activated(refer to 2.8 device selec) Under Flight Mode, it is possible to switch the dual rate and exponential, which are set in above “3) Dual Rate adjustment” and “4) Exponential adjustment”, respectively. DEVO-7 Page 113 of 170…
• Page 114
  R or L to flash SWITC, POS0,POS1 and POS2. Press R or L to choose the item to be set. After NORM mode setting finished, press DN to enter into FM1 interface, in the same way in above DEVO-7 Page 114 of 170…

• Page 115: Throttle Hold

  INH(inhabit), the factory default setting is INH If throttle hold is activated, there will be THROTTLE HOLD POSITION menu shown 2）Throttle hold position setting To activate throttle hold, please press DN to enter below interface DEVO-7 Page 115 of 170…

• Page 116: Throttle Curve

  ENT to enter into Function menu, presss UP or DN to flash THCRV,, press ENT enter into inquiring interface on wether to hold seove or not. Press R to choose YES and press L to choose NO. Press ENT to confirm. DEVO-7 Page 116 of 170…

• Page 117
  EXP ON or OFF, press R to chose ON, L to choose OFF 3）Point setting: after EXP item setting finished, presss DN, 7POINTS will be shown and press R or L to choose the point which you want to set. There are 7 points: DEVO-7 Page 117 of 170…
• Page 118
  It’s possible to switch between POS0 and POS1 when throttle lever item is inhabited. Setting: After throttle lever is finished, please press DN to enter into position setting interface as below, which shows the switch status. DEVO-7 Page 118 of 170…
• Page 119
  Press DN to enter into Switch selection interface, there are FM0, FM1, FM2, FPNRM, FPMID, FPLND, D/R, HOLD and GEAR. Press UP and DN to choose swtich; Press R to choose activate and L to inhibit. Press EXT after finish DEVO-7 Page 119 of 170…

• Page 120: Differential

  Mounting servos in left and right ailerons are a must if using this function. The following interface will be shown after Flaperon, DELTA, selected in Wing Type. Refer to “2.10 Wing Type”.Press DN in the above interface to enter position setting interface, DEVO-7 Page 120 of 170…

• Page 121
  The setting is same as above. 3)Switch selection It is possible to switch by setting switch when differential is in use. After setting Pos1 , press DN to enter “switch”item setting interface to display switch item and current switch status. DEVO-7 Page 121 of 170…
• Page 122
  After setting the above steps,Press DN to appear switch options, there are FM 0、 FM 1、FM 2、FPNRM、FPMID、FPLND、D/R、HOLD、GEAR。 Press UP or DN to select using switch, press R or L to select switch Act or Inhibit. After settings, press EXT to exit B. Rudder differential setting DEVO-7 Page 122 of 170…
• Page 123
  “FUNCTION”, press “ENT” to enter function menu, press UP or DN to appear blinking “DIFFE”, press ENT to appear channel display interface, see below. 1)Setting for Pos 0 Press R or L of Pos 0 to decrease or increase,The adjustable range is ± 100%. DEVO-7 Page 123 of 170…
• Page 124
  The setting is same as above. 3）Switch selection It is possible to switch by setting switch when differential is in use. After setting Pos1 , press DN to enter “switch”item setting interface to display switch item and current switch status. DEVO-7 Page 124 of 170…
• Page 125
  After setting the above steps,Press DN to appear switch options, there are FM 0、 FM 1、FM 2、FPNRM、FPMID、FPLND、D/R、HOLD、GEAR。 Press UP or DN to select using switch, press R or L to select switch Act or Inhibit. After settings, press EXT to exit DEVO-7 Page 125 of 170…
• Page 126
  Touch the left or right navigation mark of Pos 0 to decrease or increase, respectively, differential value. The bigger the value is, the bigger the differential is. The adjustable range is ± 100%. 2） Setting for Pos 1 The setting is same as above. DEVO-7 Page 126 of 170…
• Page 127
  3）Switch selection It is possible to switch by setting switch when differential is in use. After setting the above steps,Press DN to appear switch options, there are FM 0、 FM 1、FM 2、FPNRM、FPMID、FPLND、D/R、HOLD、GEAR。 DEVO-7 Page 127 of 170…

• Page 128: Balance

  DN, it will come out bright BALAN, press ENT to enter Channel Rudd surface, refer to below picture. 1）Channel Selection 1) Press R or L in above interface to make the channel you want flash, press DN to enter Point parameter adjustment DEVO-7 Page 128 of 170…

• Page 129: Gyro Sensor

  FUNCTION appears, press ENT to enter function menu. And then Press UP or DN, it will come out bright GYRO, press ENT to enter MODE MENUsurface, then press R or L to select Manual setting or Automatic setting DEVO-7 Page 129 of 170…

• Page 130
  AVCS mode, the bigger the value is, the bigger the gyro sensor gain will be. NOR will be activated when the value is less than 50.0%, In NOR mode, the smaller the value is, the bigger the sensitivity will be. DEVO-7 Page 130 of 170…
• Page 131
  AVCS mode, the bigger the value is, the bigger the gyro sensor gain will be. NOR will be activated when the value is less than 50.0%, In NOR mode, the smaller the value is, the bigger the sensitivity will be. DEVO-7 Page 131 of 170…

• Page 132: Governor

  The control proportion of governor can be separately set in various flight modes. For the absolute revolution amount, please set in external governor. The amount shown in DEVO-7’s governor is just a percentage for reference. The actual revolution should be read in the external governor.

• Page 133: Aileron To Rudder Mix

  Press R or L button to change the value of rudder mix when the aileron stick towards left. The mix direction will be revised by changing the sign of plus or minus before the value. The adjustable range is ±125%. DEVO-7 Page 133 of 170…

• Page 134
  The adjustable range is ±125%. 3) Pos 1 setting: the same as Pos 0. Press DN button after finished Pos 0 setting. Then go to Pos 1 left and Pos 1 right settings. The setting methods are the same. DEVO-7 Page 134 of 170…
• Page 135
  After setting the throttle stick, press DN button to “switch” setting interface. Current status will be shown. Press ENT button to “And” interface. There are “inhibit” and “active”. Press R or L to select the desired one. If two or more switches, “active” should be selected. DEVO-7 Page 135 of 170…

• Page 136: Elevator To Flap Mix

  DN button to when “FUNCTION” flash, then press “ENT” to the function menu. Press UP or DN button to until “AI—RU” flash, press ENT button to the setting of Pos 0 left. 1) Pos 0 up setting DEVO-7 Page 136 of 170…

• Page 137
  The adjustable range is ±125%. Press DN button after finished the setting of Pos 0. Then go to the setting of Pos 1 up and Pos 1 down. The setting method is the same. DEVO-7 Page 137 of 170…
• Page 138
  After setting the throttle stick, press DN button to “switch” setting interface. Current status will be shown. Press ENT button to “And” interface. There are “inhibit” and “active”. Press R or L to select the desired one. If two or more switches, “active” should be selected. DEVO-7 Page 138 of 170…

• Page 139: Rudder To Aileron/Elevator Mix

  Press “ENT” key to enter Main Menu, press UP or DN until “FUNCTION” flash , and then Press “ENT” key to enter Function Menu; Press UP or DN button until“RU—AE” becomes flash. Press ENT to enter the setting interface of Pos 0 left. DEVO-7 Page 139 of 170…

• Page 140
  Press R or L button to change the value of elevator mix when the rudder stick towards right. The mix direction will be revised by changing the sign of plus or minus before the value. The adjustable range is ±125%. DEVO-7 Page 140 of 170…
• Page 141
  Press R or L button to change the value of elevator mix when the rudder stick towards right. The mix direction will be revised by changing the sign of plus or minus before the value. The adjustable range is ±125%. DEVO-7 Page 141 of 170…
• Page 142
  Press R or L button to set the position amount of throttle stick. The default setting is Inhibit. The adjustable range is 0.0-100.0%. 4)switch setting After setting the aileron, press DN button to “switch” setting interface. Current status will be shown. DEVO-7 Page 142 of 170…
• Page 143
  FM 1, FM 2 , FPNRM, FPMID, FPLND, D/R, HOLD and GEAR。 Press UP or DN to select the desired switch; press R or L to set it “inhibit” or “active”. Press EXT to exit after finished. DEVO-7 Page 143 of 170…

• Page 144: Flaps

  1.1）Normal position: Press R or L keys to change the ELEV gyro mix amount. It is possible to change the direction by altering D or U before the amount. The default setting is 0%, and the adjustable range is U125% to D125%.(see illustration below) DEVO-7 Page 144 of 170…

• Page 145
  1.2）Midpoint The setting is same as above. 1.3）Land The setting is same as above. DEVO-7 Page 145 of 170…
• Page 146
  Press R or L to choose Inhibit and Active.Press Active another sub menu Throttle will be shown under Auto Land. 3.1）Throttle stick position setting :Press R or L change the data to set the throttle stick position. The adjustable range is 0.0-100.0%. DEVO-7 Page 146 of 170…
• Page 147
  Midpoint, and Land.“Normal” setting is manually control. 3.2.3 Flight mode 2 setting: After finished the Flight mode 1 setting,press DN to flight mode 2 setting interface,press R or L can select Normal, Midpoint, and Land.“Normal” setting is manually control. DEVO-7 Page 147 of 170…

• Page 148: Aileron To Flap Mix

  DN key until “AI—FL” becomes flashing; Press ENT key, you will find the Left at Pos 0 setting under the AI—FL interface. 1) Pos 0 setting 1.1 Left at Pos 0 Press R or L change the data to change the leftward mix value of aileron to flap. DEVO-7 Page 148 of 170…

• Page 149
  “+”or“－” will change the mix direction.The adjustable range is ±125%. 2) Pos 1 setting leftward. The setting is same as the above. 2.1)Pos 1 setting Rightward. The setting is same as the above. DEVO-7 Page 149 of 170…
• Page 150
  The default setting is Inhibit. The adjustable range is 0.0-100.0%. 4) Switch setting After setting of Throttle stick, press DN enter “Normal”interface and the “Normal”will show on the screen and the status of “Normal”. DEVO-7 Page 150 of 170…
• Page 151
  After finished the above steps, Press DN key will see switch option as follows: FM 0、FM 1、FM 2、FPNRM、FPMID、FPLND、D/R、HOLD、GEAR。 Press UP or DN to choose the available switch,Press R or L can choose Inhibit and Active,Press EXT after finished. DEVO-7 Page 151 of 170…

• Page 152: Prgmx)

  After finished above setting in the Program mix setting Press L enter Normal setting interface. Press ENT key, pop up “All Servos Hold?” Click YES for all the servos will be locked at the current statuses; click Cancel for unlocked. DEVO-7 Page 152 of 170…

• Page 153
  3.1）Mix amount setting when elevator stick moved upward: Press R or L to decrease or increase, separately, the mix amount. It is possible to reverse mix direction through changing the plus or minus sign before amount. The adjustable range is ±125%. DEVO-7 Page 153 of 170…
• Page 154
  ±125%. 3.3) Pos 1 setting:The setting is same as above. 4）Offset setting: can start from some position through switch stick in “slave channel ” interface to set the mix. The setting is same as above. DEVO-7 Page 154 of 170…
• Page 155
  The default setting is “inhibit”. The adjustable range is 0.0-100.0%。 6)switch select: Press DN after set of throttle stick, enter to the switch setting interface, and the status will show on the screen. DEVO-7 Page 155 of 170…
• Page 156
  DN key until “PRGMX” becomes flashing; Press ENT key, you will find the Program mix setting . (the factory default setting is Inhibit). Press R or L key to select the Inhibit ,Normal,Curve. Take Program Mix 1 as an example select the Curve to show how to use. DEVO-7 Page 156 of 170…
• Page 157
  AUX2、OELEV、OAILE、OTHRO、ORUDD、AUX2 2）Slave channel setting:Press DN after setting the master channel setting,then enter to the slave channel setting.see below illustration. Press R or L key,select the designed slave channel, the selectable channel as follows: ELEV、AILE、THRO、 RUDD、FLPRL、FLAP、AUX2。 DEVO-7 Page 157 of 170…
• Page 158
  R or L, select EXP”ON””OFF”. Press “ON” can make the curve circularity,press “OFF” for nonuse. 5)Point Press DN to confirm after EXP setting enter to 7 points.Press R or L to select from any DEVO-7 Page 158 of 170…
• Page 159
  Throttle stick setting:press DN ket to enter to throttle stick setting interface after set the Output setting.Press R or L can select Stick position data.the default setting is “Inhibit”,the adjustment range is 0.0-100.0%。 DEVO-7 Page 159 of 170…
• Page 160
  Press ENT to “and”interface you have two choice: inhibit and Active. Press R or L to select Inhibit or Active. Press Active when you select above two switch(include 2 switch) control. Press DN to confrim the above setting will display Switch select as follows: FM 0、 FM 1、FM 2、FPNRM、FPMID、FPLND、D/R、HOLD、GEAR。 DEVO-7 Page 160 of 170…

• Page 161: Monit

  “ENT” key to get the flashing main memu. Press UP and DN keys until “FUNCTION” becomes flashing, then press “ENT” key to Function menu. Press UP or DN key until “MONIT” becomes flashing; Press ENT key, DEVO-7 Page 161 of 170…

• Page 162: Fail -Safe

  If choose fail safe, perform the protection of out of control data set. The default setting is Servo Hold. Then press DN to choose SAFE, press DN key enter to the Fail safe setting interface. DEVO-7 Page 162 of 170…

• Page 163: Train

  It is dangerous to use full throttle, especially after fail safe taken place. 3.19（TRAIN） Two DEVO-7 transmitters working together can execute the training function to meet the requirements for the beginner. The setting method is shown as below: 1）Data copy First,using the wireless copy function of the two DEVO-7 transmitters.the model data…

• Page 164
  3） Setting for training function channels Trainee is available to get full or part of flight control power to the aircraft model via setting the training function channelin the trainer’s DEVO-7,Below is the setting method: Press ENT to show flash main menu.Press UP or DN until FUNCTION flash,repress ENT to enter function menu;…
• Page 165
  At the same time, the output date of open interface should be the operated data of trainee. If trainer move away TRN, that means trainer will get back the operated right from trainee and operate the model. DEVO-7 Page 165 of 170…

• Page 166: Timer

  Press UP or DN,make interface showed flash”TIMER” menu, press”ENT” to enter type selection. There are stopwatch and countdown. Press R or L to select. A)Stopwatch setting, the following interface for stopwatch,press EXT to exit DEVO-7 Page 166 of 170…

• Page 167
  Press R or L to set countdown. The countdown rang of is from00:05-59:55. C）usage method Press UP on “ on” interface AN to start on the first time,repress UP to stop; press DN,timer is the orginal 0 DEVO-7 Page 167 of 170…

• Page 168: Part Four: Upgrade Interface

  Part four: Upgrade interface Devo 7 can upgrade the program via UP02 Enter the interface: Turn off the transmitter first, then press the EXT and turn on the power as below : DEVO-7 Page 168 of 170…

• Page 169
  Run the UP02 program in the PC.Details please follow the UP02 upgrade manual. Replace only with same or equivalent batteries. Dispose of used batteries according to the relevant regulations. This symbol indicating separate collection for electrical and electronic equipment. DEVO-7 Page 169 of 170…
• Page 171
  DEVO-7 Page 170 of 170…