Fishman prefix pro blend инструкция

Quick Links

Quick Links

U S E R ’ S G U I D E

TM

PROBlend

ACOUSTIC GUITAR SYSTEM

WARNING!

WE STRONGLY RECOMMEND THAT YOU FAMILIARIZE YOURSELF WITH THE PREAMP CONTROLS BEFORE YOU ATTEMPT TO PERFORM WITH THE ONBOARD BLENDER. FAILURE TO DO SO COULD RESULT IN WAVES OF EAR-SPLITTING FEEDBACK AT HIGH LEVELS. (see Quick Start on page 3.)

F I S H M A N P R E F I X ™ S E R I E S

Congratulations! With your new Fishman Prefix™ProBlend we are pleased to offer a total onboard amplification system in a very small and unobtrusive package. This is a simple yet sophisticated system, so please take a few minutes to familiarize yourself with the control layout and go over the Quick Start instructions on the next page. If you have any questions please contact our Customer Service Department at 978.988.9665 or tech@fishman.com

The Prefix™ProBlend is an acoustic guitar system that combines the sounds from a Fishman Acoustic Matrix™ pickup and a miniature electret condenser microphone. The microphone, shock-mounted on the underside of the preamp chassis, captures the elusive natural ambience and resonance of the guitar’s sound chamber. The Acoustic Matrix™ pickup delivers a clear, articulate sound with emphasis on string definition and attack. When combined, the two signals produce a powerful and cohesive acoustic guitar tone that is much greater than the sound of either microphone or pickup alone.

Downsized to fit even the thinnest of guitars, the second generation Prefix™ProBlend preamp occupies 1/3 less surface area on the side of a guitar than our standard Prefix™ series. The preamp module incorporates a space saving «flip-top» battery compartment for easy access.

Levels are set by the master VOLUME and BLEND controls. BASS & TREBLE controls, a semi-parametric CONTOUR control, a NOTCH filter and PHASE switch are included for precise tone shaping and feedback control. You may plug the PREFIX™ PRO BLEND into any instrument-level audio input.

THE PICKUP

The included Acoustic Matrix™ pickup is made with a proprietary co-polymer sensing material, available exclusively from Fishman. Unlike so called «piezo-film» pickups, our unique copolymer formula is not available from any other manufacturer. Sound-wise, the Acoustic Matrix™ exhibits a sensitivity and dynamic range that far surpasses all other known pickups.

The Acoustic Matrix™ transducer is a fully EMI shielded, multi-layer sandwich of co-polymer strips that run the length of the pickup. This design allows the pickup to sense the motion of the entire saddle length, providing superb string to string balance, as well as sensitivity to both the strings and the soundboard of the instrument.

THE MICROPHONE

The microphone, in conjunction with PHASE, NOTCH and CONTOUR controls (see page 6), will provide very high level sound reproduction before feedback. Conveniently shock-mounted to the back of the preamp case, the microphone is acoustically isolated inside the instrument, providing freedom of movement as well as minimal leakage from other instruments on stage.

2

P R E F I X ™ P R O B L E N D

QUICK START

To combine microphone and pickup signals, first preset the microphone EQ to control feedback, then mix in the pickup. The Prefix™ProBlend has three ways to control feedback; a Notch Filter, a Phase Switch, and a Semi-parametric Contour Control.

Follow these steps to achieve a strong, feedback-free sound.

1.Before you plug in, set all controls as follows:

•NOTCH and VOLUME fully counter-clockwise

•All sliders at their center positions

•BLEND slider at MIC position

2.Plug in the instrument first (with 9V alkaline battery installed), then plug in to your amplifier, with the tone controls on the amp set as flat as possible.

3.Slowly increase the VOLUME until the guitar and speaker are approximately the same level. Play the open E string and flip the PHASE switch. Leave the switch in the position that sounds the deepest and clearest. (for more on phase, see page

4.Slowly increase the volume until the instrument starts to rumble with low frequency feedback

5.Use the NOTCH FILTER to scoop out the lowest range of feedback, which usually starts at the open low E string and continues up to about the forth fret G# on the same string (often near two ‘o clock).

6.Use the PHASE SWITCH to control the upper range of low frequency feedback, which usually starts at the fifth fret A on the low E string and continues up to about the twelfth fret E on the same string. Flip the PHASE SWITCH back and forth until you find the position that subdues this range of feedback.

7.Slowly increase the VOLUME again, until the microphone just starts to squeal.

8.Lower the CONTOUR Level all the way down. Slowly adjust the Contour FREQUENCY rotary control until the squealing feedback is eliminated. Raise the CONTOUR Level slider (if possible) to just below the threshold of feedback.

9.Gradually mix in the pickup signal by adjusting the BLEND slider. The pickup signal will add significant attack and definition to your sound.

10.Adjust the BASS and TREBLE controls as desired. Please note that these controls will affect pickup signal only.

11.Double check the PHASE switch position until you find the clearest, feedback free response.

12.Play your guitar as loud as you want..

F I S H M A N P R E F I X ™ S E R I E S

FUNCTIONS

Battery Compartment

Pull the small tab at the top of the Problend™ toward you. The body of the preamp will swing out, revealing the BATTERY COMPARTMENT. Install a fresh 9V alkaline battery.

Microphone Trim Control

A small circular potentiometer is located on the side of the preamp that faces the back of the guitar. This control can be accessed by opening the battery compartment. Use this control to fine tune the microphone volume, in relation to the pickup volume. To adjust the microphone trim control, set the BLEND slider to the center position and, with a slotted jewelers screwdriver, turn the potentiometer until both the microphone and pickup levels are balanced to your taste.

POWER

The Prefix™ProBlend has no ON/OFF switch. To turn on the power, plug an instrument cable into the endpin jack. To conserve the battery, remove the instrument cable from the endpin jack when the unit is not being used. It is a good idea turn down your amp or mixer’s input before you plug into this input. Doing so will protect your speakers (and your ears) from loud pops and thumps.

Clip / Battery Low LED

This light has three distinct functions:

1. Power Up Indicator

The Clip/Batt Low LED will flash momentarily when you first turn on the preamp. Some people ask us why this light doesn’t stay on, like a conventional pilot light. We feel a steadily lit LED devours too many precious hours of battery life. We prefer instead to conserve the battery with a quick flash of the LED to indicate that the preamp is powered up.

2. Clip Indicator

If the LED flashes while you are playing, you are driving the preamp into distortion. Lower the Treble and/or Bass slider until the flashing stops. This indicator may also flash as you approach the end of the battery’s useful life.

3. Low Battery Warning

When the Clip/Low Batt LED lights steadily, it is time to change the battery.

Volume

Affects both microphone and pickup levels. Set this as high as possible (without distorting your amp or mixer) for the cleanest signal.