Fubag in 160 инструкция на русском

• Operator's  manual
  www.fubag.ru
  WARNING! BEFORE USING THE WELDING MACHINE READ THE INSTRUCTION
  MANUAL CAREFULLY! FOR QUALIFIED AND SPECIALLY TRAINED PERSONS
  ONLY AFTER PROPER READING OF THIS MANUAL IS ALLOWED TO USE AND TO
  MAINTAIN THIS WELDING MACHINE.
  The detailed description, safety rules and all required information necessary for proper operation
  and maintenance of FUBAG welding machine are provided below. Keep this instruction manual by
  machine and refer to it by any doubts concerning safety operation, maintenance storage and
  handling of FUBAG welding machine.
  1. Safety perationo
  - It is highly recommended always to follow the safety rules. Wear protective clothes and
  special means to avoid injuries to eyes and skins.
  - Use the welding mask or special protective glasses while working with the welding
  machine. Only by viewing through the filter lens on the welding mask your eyes are
  secured by your operation.
  - Prevent the sparks and spatter from harming your body.
  - Under no circumstance allow any part of your body to touch the welder's output bipolarity
  (torch and work piece).
  - Do not operate under water or more humid place.
  - Fumes and gases produced when welding are hazardous to health. Make sure to work in
  places where there are exhaust or ventilation facilities to keep fumes or emissions away
  from the breathing zone.
  - Please remember to keep arc rays away from the other nearby people when welding. This
  is only due to the interference from arc rays.
  - There will be high temperature when welding work piece, so please don't directly touch on it
  - No touching on the output connection or any other electrification parts while welding.
  - No touching on the electrification parts after turning on the power. Cut off the power supply
  after operation or before leaving the welding site.
  - No welding in the dangerous site where easily get an electrical shock.
  - No welding for the container loaded inflammable or explosive materials.
  - Safe measures should be adoptted while operating in high place to avoid accident.
  - No entering the welding site for persons not concerned.
  - Welders possible have electromagnetism and frequency interference, so keep away people
  with heart pace or the articles which can be interfered by electromagnetism and frequency.
  WARNING. The welder voltage is always higher, so the safety precaution should be taken
  before repair to avoid accidental shock. Switch off the power supply before each type of
  maintenance work. The untrained people are not allowed to make maintenance of the
  machine.
  -1-

• Operator's  manual
  www.fubag.ru
  - Check the connection of input and output cables and the earth (ground) connection, etc.
  - Maintenance should be conducted by the trained personnel.
  - The newly installed machine or the welder not in use for some time needs to be checked by
  multimeter have the right insulation resistance between each winding and the case.
  - When the welder is used outdoors, it should be kept from rain or long exposure to the sun.
  - Check is needed from time to time to make sure the welding cable is in good condition if the
  welding machine is in frequent use. Check at least once each month if the welder is in
  regular use. It is necessary to check when the welder is in mobile use.
  - If the welder is not in use either for a long time or temporarily, it should be kept dry and have
  good ventilation to free it from moisture, erodible or toxic gas.
  - Dust removal is needed every year. Check the machine's fasteners, moving-iron, current
  regulation screws, etc to make sure there are no loose connection problems.
  - The dust, acid and erodible dirt in the air at the job site can not exceed the amount required
  by the norm (excluding the emission from the welder).
  - The welder must be installed in the place where it can not be exposed to sun and rain. Also it
  must be stored in less humid place with the temperature.
  - When the machine is operating, the temperature must not be higher than  +40 °C or lower
  than  -10 °C.
  - There should be 50 cm space about for the welding machine to have good ventilation.
  - Make sure that there is no metal-like foreign body to enter the welding machine.
  - Electrode must be taken down from holder when no welding.
  - No violent vibration in the welder's surrounding area.
  - Make sure that there is no interference with the surrounding area at the installation site.
  Safety Check:
  Each item listed below must be carefully checked before operation:
  - Make sure that there is no short circuit connection with welder's both outputs.
  - Make sure that there is always sound output and input wire connection instead of exposing it
  outside.
  Regular check needs to be conducted by the qualified personnel after the welding machine has
  been installed over a long period or re-operation, which involves as follows:
  - Check the welding cable to see if it can continue to be used before it is worn out.
  - Replace the welder's input cable as soon as it is found to be broken or damaged.
  - Make sure whether there is enough power supply to make the welding machine work properly.
  Any power source required to access the welding machine must be installed with some
  protective equipments.
  Please do not hesitate to contact us for technical assistance whenever you come across the
  problems you can not work out or you may deem difficult to fix.
  - 2  -

• Operator's  manual
  www.fubag.ru
  2. Technical pecificationss
  220
  220
  220
  The manufacturer reserves himself the right to make the manual's content or welder's function
  change without any preliminary notification of the users.
  3. Description е
  The FUBAG IN 12 , 13 , 16 are portable, single-phase, air cooled Inverter welding units, for MMA
  electrode welding with direct current. They can weld all kind of electrode : rutile, cast-iron, basic,
  stainless steel. They are over-voltage protected when used on power 220 V +/- 10%.
  IN120                     IN130                     IN160
  1                  1                         1
  2              2                         2
  3                         3
  3
  4                     4                         5
  5             5                         4
  1. Current setting
  2. Power indicator (green)
  3. Thermal protection indicator (yellow)
  4. External connector for ground clamp
  5. External connector for electrode holder
  -3-

• 1
• 2
• 3
• 4
• 12

Формат файла: PDF

Доступность: Бесплатно как и все руководства на сайте. Без регистрации и SMS.

Дополнительно: Чтение инструкции онлайн

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Оглавление инструкции

• Страница 1 из 15
  
• Страница 2 из 15
  Operator’s manual www.fubag.ru WARNING! BEFORE USING THE WELDING MACHINE READ THE INSTRUCTION MANUAL CAREFULLY! FOR QUALIFIED AND SPECIALLY TRAINED PERSONS ONLY AFTER PROPER READING OF THIS MANUAL IS ALLOWED TO USE AND TO MAINTAIN THIS WELDING MACHINE. The detailed description, safety rules and all
• Страница 3 из 15
  Operator’s manual www.fubag.ru — Check the connection of input and output cables and the earth (ground) connection, etc. — Maintenance should be conducted by the trained personnel. — The newly installed machine or the welder not in use for some time needs to be checked by multimeter have the right
• Страница 4 из 15
  Operator’s manual www.fubag.ru 2. Technical specifications 220 220 220 The manufacturer reserves himself the right to make the manual’s content or welder’s function change without any preliminary notification of the users. 3. Descriptionе The FUBAG IN120, 130, 160 are portable, single-phase, air
• Страница 5 из 15
  Operator’s manual www.fubag.ru 4. Illustration of signs S X /10min O @40 C … I 2 U … % % … 2 % -4-
• Страница 6 из 15
  Operator’s manual www.fubag.ru 5. Power supply — This machine is delivered with a 16 А (for IN120), 20A (for IN130) или 25А (for IN160) plugged on a 220V (50 Hz) socket with earth. — Connect the earth clamp and electrode-holder cables in the quick-plugs. Respect the polarities indicated on the
• Страница 7 из 15
  Инструкция по эксплуатации www.fubag.ru 8. Troubleshooting 220V +/- 10%. 220V +/- 10%. 9. Transport & storage When the welder is in storage and transportation, please try to keep it from being exposed to the rain. When loading, attach ATTENTION to the welder packing. It is recommended to free it
• Страница 8 из 15
  Инструкция по эксплуатации www.fubag.ru ВНИМАНИЕ! ПЕРЕД ИСПОЛЬЗОВАНИЕМ СВАРОЧНОГО АППАРАТА ВНИМАТЕЛЬНО ОЗНАКОМЬТЕСЬ С ДАННОЙ ИНСТРУКЦИЕЙ. К использованию и обслуживанию сварочного аппарата допускается только квалифицированный и специально обученный персонал, ознакомленный с данной инструкцией. В
• Страница 9 из 15
  Инструкция по эксплуатации www.fubag.ru — Проверьте подключение входных и выходных кабелей, заземление и т.д. — Техническое обслуживание должны выполнять только квалифицированные специалисты. — Если ваш сварочный аппарат был только что установлен или к работе приступает новый оператор, следует
• Страница 10 из 15
  Инструкция по эксплуатации www.fubag.ru 2. Технические характеристики 220 220 220 Производитель имеет право вносить изменения как в содержание данной инструкции, так и в конструкцию сварочного аппарата без предварительного уведомления пользователей. 3. Описание Данный сварочный аппарат является
• Страница 11 из 15
  Инструкция по эксплуатации www.fubag.ru 4. Расшифровка пиктограмм и предупредительных знаков S … X /10min O @40 C % … I 2 U % … 2 % е — 10 —
• Страница 12 из 15
  Инструкция по эксплуатации www.fubag.ru 5. Подключение питания — Подключите аппарат к розетке 16 А (для IN120), 20A (для IN130) или 25А (для IN 160) к сети 220В (50 Гц) с заземлением. — Подсоедините зажим массы и электрододержатель к сварочному аппарату в зависимости от полярности, соответствующей
• Страница 13 из 15
  Инструкция по эксплуатации www.fubag.ru 8. Неисправности и их устранение 220В +/- 10%. 220В +/- 10%. 9. Хранение и транспортировка Во время транспортировки и хранения сварочного аппарата старайтесь беречь его от попадания влаги. Рекомендуется хранить сварочный аппарат в сухом, хорошо проветриваемом
• Страница 14 из 15
  
• Страница 15 из 15