Газовая плита виктория гдр инструкция по применению

• Page 1
  INSTRUCTION MANUAL for installation and operation of air pellet stove VITTORIA 8 / VITTORIA 10…

• Page 2: Table Of Contents

  Victoria-05 Ltd. CONTENTS 1. INTRODUCTION…………………………….3 2. SAFETY INFORMATION…………………………..3 3. TECHNICAL DATA AND DIMENSIONS……………………….4 4. SAFETY DEVICES…………………………….5 5. CONTROL UNIT…………………………….6 6. COMPONENTS…………………………….6 7. OPERATING MODE……………………………. 6 8. FUEL………………………………..7 9. APPLIANCE INSTALLATION…………………………8 10.

• Page 3: Introduction

  12.2018 INSTRUCTION MANUAL for installation and operation of pellet stove VITTORIA 8 / VITTORIA 10 1. Introduction. We congratulate you on the excellent choice! Do not leave this instruction manual unread. Installation and operation of a pellet stove associated with various legal obligations, which are explained in this instruction manual.

• Page 4: Technical Data And Dimensions

  Victoria-05 Ltd. 3. Technical data and dimensions. Drawing.1.

• Page 5: Safety Devices

  12.2018 INSTRUCTION MANUAL for installation and operation of pellet stove VITTORIA 8 / VITTORIA 10 Technical data and nominal performance: Performance parameters: Technical data Vittoria 8 Vittoria 10 Nominal heat output 6.1 kW 8.0 kW Reduced heat output 3.0 kW 3.7 kW…

• Page 6: Control Unit

  Victoria-05 Ltd. 5. Control unit. The control unit is equipped with a system for monitoring and controlling of the burning process. It ensures higher efficiency, optimizes the fuel consumption and minimizing the emissions. With sensors for the pressure in the fire chamber and temperature sensors at the flue outlet for the temperature of the flue gasses, the system analyzes the collected data from the burning and automatically controls it and optimizes it.

• Page 7: Fuel

  12.2018 INSTRUCTION MANUAL for installation and operation of pellet stove VITTORIA 8 / VITTORIA 10 The initial ignition of the pellets is carried out by hot air, which is sucked in around the ignition (K) in the combustion chamber through the fume extractor (G). Fume extractor provides combustion air by sucking in from air inlet Ø40 mm (D) by the room or by outside atmosphere.

• Page 8: Appliance Installation

  Victoria-05 Ltd. 9. Appliance installation. Trained and competent technicians or companies must perform the installing a pellet stove! Qualified technicians should perform all activities in inspection and repair of electrical components. Switch off the pellet stove from the electric supply before any inspection or repair! Refer to the regulations valid for the country, where the pellet stove will be used, if you do not find the information you are interested in this instruction manual.

• Page 9: Appliance Operation

  Before ignition, check: power, door seal, if the combustion chamber is cleaned and whether the display is switched to standby mode. 10.2. Control panel description After start up, on the control display is shown the logo of Victoria-05 for 3 seconds and then switches to main user panel. The icons and functions are shown as follows: Picture.4.

• Page 10: Main User Control Panel

  Victoria-05 Ltd. 10.2.1. Main user control panel. To visualize every function from the display it is necessary to touch the respective icon. The blue arrow in the sub menu is for returning to the previous screen. By pressing SAVE all corrections are saved. The left and right arrows are for decreasing and increasing the value of the respective parameter.

• Page 11: Main Menu

  12.2018 INSTRUCTION MANUAL for installation and operation of pellet stove VITTORIA 8 / VITTORIA 10 10.2.3. Main menu. Air correction ±15% sets in percentage the adjustment of the power of smoke during operation mode and the pause length of the feed screw.

• Page 12: Installer Settings

  2468.After that access have to be touched to unlock the display. 10.2.4. Installer settings. Factory settings Types of settings for Installer (entered with installer password) Vittoria 8 Vittoria 10 Duration 700 sec. 700 sec. 55 %…

• Page 13: Service Technician Settings

  12.2018 INSTRUCTION MANUAL for installation and operation of pellet stove VITTORIA 8 / VITTORIA 10 From this menu, the default language can be set. – Bulgarian, English, Netherlands, Deutsch. 10.2.5. Service technician settings. Types of settings for service technician (entered with…

• Page 14: Cold Test

  Victoria-05 Ltd. Indoor fan- we can choose between 1%to 100%.Choosing from 1 to 100 and then safe, at the exit of the indoor fan OUT3 is triggered modulation of the power. 10.3. Cold test. The cold test is necessary to check the working order and proper connection of electrical components in the pellet stove. The test of the outputs is possible only in ready mode.

• Page 15: Maintenance

  12.2018 INSTRUCTION MANUAL for installation and operation of pellet stove VITTORIA 8 / VITTORIA 10 In Modulation mode, by touching the field showing the current modulation, we can change and set the modulation preset that we like. If the stove is working in P3 and we touch the field, the preset will change to P2. If touched again, it will change to P1.

• Page 16: Maintenance And Control

  Victoria-05 Ltd. Check sensors; Check and, if necessary, replace the battery on the control panel; Clean and check the electronic control system; Check all electrical cables; Clean the pellet fuel hopper and check auger for loosen screw and the gear motor;…

• Page 17: Frequently Asked Questions

  12.2018 INSTRUCTION MANUAL for installation and operation of pellet stove VITTORIA 8 / VITTORIA 10 Activated timer Red color: the timer is activated and waiting for the set time to stop the stove. Activated timer Green color: the timer is activated and waiting for the set time to start the stove.

• Page 18: Technical Documents

  Victoria-05 Ltd. Yes, at least once a month or if the pellet stove has not worked for a long time. Can you use other types of fuel than wood pellets? NO. Pellet stove is designed to work with wood pellets with a diameter of Ø 6 mm. The use of another type of fuel leads to damage.

• Page 19
  12.2018 INSTRUCTION MANUAL for installation and operation of pellet stove VITTORIA 8 / VITTORIA 10…
• Page 20
  Victoria-05 Ltd.
• Page 21
  12.2018 INSTRUCTION MANUAL for installation and operation of pellet stove VITTORIA 8 / VITTORIA 10…
• Page 22
  Victoria-05 Ltd.
• Page 23
  12.2018 INSTRUCTION MANUAL for installation and operation of pellet stove VITTORIA 8 / VITTORIA 10…

• Page 24: Spare Parts Catalogue

  Victoria-05 Ltd. SPARE PARTS CATALOGUE № Denomination Gear motor for auger Fume extractor ST25, aluminum volute Ø150, encoder (set) Auger (set) Ignition Pressure switch Controller(set) Display Crossflow blower Glass (4 x 261x 310) Glass sealing (set) Combustion chamber (set) Fire-grate…

• Page 25: Warranty Conditions

  Failing that provided, the claim is not accepted as valid and the buyer pays repair. On the territory of Bulgaria the term of the removal of the claim is up to three (3) days for settlements in which Victoria-05 Ltd.

• Page 26: Diary

  Victoria-05 Ltd. DIARY for repairs under warranty № Company Receipt date Type of repair Delivery date Carried out…

• Page 27
  12.2018 INSTRUCTION MANUAL for installation and operation of pellet stove VITTORIA 8 / VITTORIA 10…
• Page 28
  Victoria-05 Ltd. 1B Ivan Momchilov Str. 5100 Gorna Oryahovitsa Republic of Bulgaria phone: +359 618 60282 fax: +359 618 60200 e-mail: info@v05.bg http://www.v05.bg…

FAQ

Курсы

О компании

Клиентам

Неисправности

Контакты

• Page 1
  Instruction for installation and operation of pellet burning stove with integral water boiler VITTORIA В*…

• Page 2: Table Of Contents

  Contents 1. Introduction: …………………………………………….……………………………………….. 3 2. Safety information: …………………………………….…………………..…………………. 3 3. Technical parameters: ………………………………….…………………..……………….. 4 4. Safety devices: ……………………………………………….………………………………….. 6 5. Electronic circuit board: ………………………………….………………..……………….. 6 6. Principle of operation: …………………………………….………………………….……… 7 7. Operation ………………………………………………………….……………………..………… 8 8. Safety and detection devices: …………………………….…………………….………… 8 9.

• Page 3: Introduction

  1.Introduction: We congratulate you on the excellent choice! We wish you many pleasant moments with your new pellet stove. Do not leave the instructions unread. The installation and exploitation of the pellet stove should be made in accordance with different legal obligations, which are explained in this instruction. According to the laws and regulations for safety, when using an appliance of such class, the buyer and the user are obliged, with the help of this instruction, to inform themselves for the assembling and the right operation of the appliance.

• Page 4: Technical Parameters

   Durring the stove is in operation, the exhaust pipes and door become very hot.  Do not place anything that is not heat resistant near the stove.  NEVER use liquid fuel to ignite the stove or rekindle the embers …

• Page 5
  Technical and heating parameters: Specifications: Performance parameters: Distance to flammable materials Minimum distance, in mm. side=400 back=400 front=800 Flue outlet Ø 8 cm СО emissions [13% О 0,0132 % Output flue gas amount 12,23g/s Working pressure of the water 1,5 bar Maximum test pressure of the water 3 bar °…

• Page 6: Safety Devices

  4.Safety devices: -Thermocouple: Placed at the smoke outlet to detect temperature. Turns the stove on and off and also controls its operation based on defined parameters. -Vacuum gauge: (electronic pressure sensor) Placed on the smoke extractor which detects the vacuum value (compared to the installation enviroment) in the combustion chamber -Safety thermostat: Switches off when the temperature in the stove is too high.

• Page 7: Principle Of Operation

  The pellet stove is equipped with system which ensures optimal burning. The system ensures excellent operation thanks to two sensors measuring the pressure level in the combustion chamber and smoke temperature. The detection of and subsequent optimisation of these two parameters is continuous in order to correct opera- tion anomalies in real time.

• Page 8: Operation

  7.Operation: The required temperature of the water in the system is adjusted and set by the control panel (recommended C) and the stove manually or automatically changes the power to reach and keep the temperature. Fuel notes: — The stove is designed and programmed to use and burn wood pellets with diameter 6 mm. — The pellets are type of fuel which is made from heavily compacted under very high presure chopped waste wood and saw dust.

• Page 9: Installation

  Closed expansion tank Absorbs the differences in the volume of the water caused by the heating. Technician has to decide is it needed to add second tank to the existing one, depending from the volume of the water in the system. Venting valve (deaerator) Positioned on the top part, allowing to bleed the system from any air inside, present during filling with water.

• Page 10
  The room where the stove is placed must have an air inlet with a cross-section of at least 80 cm² so as to guarantee sufficient air supply to the stove for combustion. Alternatively, the stove air may be taken directly from outside through a 5 cm steel extension of the pipe.

• Page 11: Basic Instructions For Use

  Water treatment. Consider and ensure adding the appropriate antifreeze or other compounds against freezing and corrosion. If the water is exceeding the hardness value of 35˚F, you should use water softener. Note: the person responsible for the heating system should consider and ensure additional heat extension tank depending from the system.

• Page 12: Instructions For Use

  — Check and verify the correct installation of the components in the system and also is the system equipped with appropriate expansion tank to ensure safe work. The presence of heat expansion tank in the stove itself, does not guarantee adequate protection from overheating the water. — Connect the electric supply and make a cold test (performed by the dealer) — Fill up the system form the filling tap (recommended not to exceed 1 bar pressure.) During filling up the system, bleed the circulation pump.

• Page 13
  When the stove is operational by pressing button 0/1 for 2 seconds, the process for shutting down the stove is started and OFF is displayed for 10 minutes. Shutdown phase includes: Pellet feeding is stopped. Stopping the circulation of the water. Never pull off the plug during shutdown process! Please have a note that the circulation pump will work till the temperature of the water drops under 40 Setting the clock:…

• Page 14: Maintenance

  From this moment the display will show the remaining quantity of the pellets in kg. (15 … 14 … 13). Every time when pellets are loaded you must enter the quantity. When loaded 15 kg. just press “pellet load” button. For different quantity or if there is a mistake, you can specify the quantity by using the menu as follows: Press “MENU”…

• Page 15: Possible Troubleshooting

  Picture 10 Picture 11 The amount of dust depends from the used fuel. Failure to do the cleaning procedure can cause the stove to block. After the cleaning procedure is completed, make sure that all service openings are closed and sealed properly. Seasonal maintenance (performed by the dealer): The dealer firstly is setting the amount of pellets consumed after which the message “Maiten??”…

• Page 16
  2. VERIFIC./EXTRACT: Shuts down due to the revolution sensor of the smoke extractor motor detecting an anomaly. — Check smoke extractor functionality (connection of the revolution sensor) — Check smoke channel for dirt. 3. STOP/FLAME: Shuts down due to a drop in smoke temperature (intervenes if the thermocouple detects a smoke temperature that is lower than that which is set, thereby interpreting it as a flame failure).

• Page 17: Check List

  16. Check list: Positioning and instalation: — Enough room ventilation. — Only the stove outlet passes through the smoke channel/chimney. — Smoke pipes have maximum 2 curves, maximum length 2 meters and at least 1,5 m vertical pipeline. — The exhaust pipes are made by appropriate material (stainless steel recommended) — When using any flammable materials (wood for example) all precisions have been taken to prevent fire hazard.

• Page 20: Warranty Conditions

  Warranty conditions: The producer guarantees the proper working of the stove in 24 months term from the day of selling in the store, except for the parts which are consumptives, in case that all requirements for proper storing, transportation, installation and use are kept. Installing of the stove and the heating system must be completed by authorized licensed organization in accordance with the instructions given in this instruction manual! When claiming the stove you must present receipt and invoice for buying the stove and the original of the warranty card.

• Page 21
  Victoria-05 Ltd. 61A Anton Strashimirov Str. 5100 Gorna Oryahovitsa Bulgaria phone: +359 618 60282 fax: +359 618 60200 e-mail: info@v05.bg…