-
Contents
-
Table of Contents
-
Troubleshooting
-
Bookmarks
Quick Links
HK 980 Integrated Amplifier
OWNER’S MANUAL
Related Manuals for Harman Kardon HK 980
Summary of Contents for Harman Kardon HK 980
-
Page 1
HK 980 Integrated Amplifier OWNER’S MANUAL… -
Page 2: Table Of Contents
Table of Contents 3 Introduction 4 Connections 5 Controls and Functions 6 Remote Control 7 Operating Instructions 7 Troubleshooting 8 Specifications TABLE OF CONTENTS DECLARATION OF CONFORMITY We, Harman Consumer Group International 2, route de Tours F-72500 Château-du-Loir France declare in own responsibility, that the product described in this owners manual is in compliance with technical standards: EN 55013:2001 + A1:2003…
-
Page 3: Introduction
Introduction Introduction Congratulations on your choice of the Harman Kardon HK 980 Integrated Amplifier. In order to obtain the best performance from this integrated amplifier, please be sure to read this owner’s manual and use your integrated amplifier only in accordance with its instructions.
-
Page 4: Connections
Input jacks on the back of your amplifier and, if available, the compo- nent’s Input/Record jacks to the Output jacks of the HK 980. Use the white, black or gray plugs to connect Left channel jacks; use the red plugs for Right channel jacks.
-
Page 5: Controls And Functions
2 System Power Control: Press this button to turn on the HK 980; press it again to turn the unit off (to Standby). Note that the Power Indi- cator 1 next to the switch will turn blue when the unit is on.
-
Page 6: Remote Control
Remote Control Independent Remote Control The system remote of the HK 980 can control the amplifier and compatible Tuners, CD Players and CD Recorders. The remote In jack of units without an integrated IR receiver must be connected to the amplifier’s remote control output jack so that the system remote control can operate them.
-
Page 7: Operating Instructions
Operating Instructions Listening to your CD player, tape deck, tuner or other source 1. Turn Volume control to minimum level and press the flat Power switch to turn on the amplifier. The power indicator lights blue and the protection circuitry checks for short circuit or other problems for a few seconds before sound output.
-
Page 8: Specifications
Specifications Continuous Average Power Per Channel (FTC) 20 Hz – 20 kHz, both channels driven Dynamic Power (IHF, 1 kHz Tone Burst) High instantaneous current capability (HCC) Power Bandwidth @ Half-Rated output, 8 Frequency response @ 1W (+0/-3dB) Damping factor (20Hz-20k Hz) Signal-to-noise Ratio (Reference rated power output, A-WTD) Input sensitivity/Impedance Overload:…
Посмотреть инструкция для Harman Kardon HK 980 бесплатно. Руководство относится к категории приемники, 2 человек(а) дали ему среднюю оценку 8.3. Руководство доступно на следующих языках: английский. У вас есть вопрос о Harman Kardon HK 980 или вам нужна помощь? Задайте свой вопрос здесь
Не можете найти ответ на свой вопрос в руководстве? Вы можете найти ответ на свой вопрос ниже, в разделе часто задаваемых вопросов о Harman Kardon HK 980.
Когда звук считается слишком громким?
Могут ли устройства разных марок подключаться друг к другу при помощи Bluetooth?
Как лучше всего выполнять чистку приемник?
Инструкция Harman Kardon HK 980 доступно в русский?
Не нашли свой вопрос? Задайте свой вопрос здесь
Скачать
HK 980 Integrated Amplifier
OWNER’S MANUAL
ENGLISH
Specifications:398/398182-hk_980.pdf file (28 Dec 2022) |
Accompanying Data:
Harman Kardon HK 980 Home Theater System PDF Owner’s Manual (Updated: Wednesday 28th of December 2022 05:34:58 AM)
Rating: 4.4 (rated by 33 users)
Compatible devices: AVR 635, HKTW 6, HS 100, AVR 155, BDS 335, AVR 70/230, BDS, HS 350.
Recommended Documentation:
Text Version of Owner’s Manual
(Ocr-Read Summary of Contents of some pages of the Harman Kardon HK 980 Document (Main Content), UPD: 28 December 2022)
-
3, Harman Kardon HK 980 INTRODUCTION 3 IntroductionIntroduction Congratulations on your choice of the Harman Kardon HK 980 Integrated Amplifier. In order to obtain the best performance from this integrated amplifier, please be sure to read this owner’s manual and use your integrated amplifier only in accordance …
-
5, CONTROLS AND FUNCTIONS 5 Controls and Functions 1 Power Indicator: This LED will illuminate in amber when the unit is in the Standby mode to signal that the unit is ready to be turned on. When the unit is in operation, the indicator will turn blue. 2 System Power C…
-
8, 250 Crossways Park Drive, Woodbury, New York 11797 www.harmankardon.com Harman Consumer Group International: 2, Route de Tours, 72500 Château-du-Loir, France © 2007 Harman Kardon, Incorporated Part no. 8543 4813 0101 Specifications NOMINAL Continuous Average Power Per Channel (FTC) 8 Ohms: 80 Watts@…
-
7, OPERATING / TROUBLESHOOTING 7 Operating Instructions Listening to your CD player, tape deck, tuner or other source 1. Turn Volume control to minimum level and press the flat Power switch to turn on the amplifier. The power indicator lights blue and the protection circuitry checks for short circuit or other …
-
2, Harman Kardon HK 980 2 TABLE OF CONTENTS 3 Introduction 4 Connections 5 Controls and Functions 6 Remote Control 7 Operating Instructions 7 Troubleshooting 8 Specifications Table of Contents We, Harman Consumer Group International 2, route de Tours F-72500 Château-du-Loir France declare in own responsibility, th…
-
Harman Kardon HK 980 User Manual
-
Harman Kardon HK 980 User Guide
-
Harman Kardon HK 980 PDF Manual
-
Harman Kardon HK 980 Owner’s Manuals
Recommended: RM 7390 (L), CONROE1333-D667 — INSTALLATION 11-2007, RC45180
-
Onkyo 9555 — A Amplifier
En Integrated Amplifier A-9755/A-9555 Instruction Manual Thank you for purchasing an Onkyo Integrated Ampli-fier. Please read this manual thoroughly before makingconnections and plugging in the unit.Following the instructions in this manual will enableyou to obtain optimum performance and listeningenjoyment from y …
9555 — A Amplifier 20
-
Sony SU-36HX1
1INSTRUCTIONSThe SU-36HX1 TV stand is designed for use only with Sony 36-inch TV set listed to the right.INSTRUCCIONESEste soporte del televisor SU-36HX1 ha sido diseñado para ser usado solamente con el televisor Sony de 92 cm (36 pulg.) notado a la derecha.INSTRUCTIONSLe meuble de télévision SU-36HX1 est con …
SU-36HX1 16
-
Sony BDV-T58
BDV-T58 Key Features1000 watt 5.1 channel surround sound (167 Wx5 +165 W)12 Internet streaming: Netflix®, YouTube™, Pandora® & more 3 Built-in Wi-Fi®2x HDMI™ inputs with 3D pass-through support Includes iPod®/iPhone® dock (video, music and photos)5 Multi-room Music with PartyStreaming7 App …
BDV-T58 2
-
Philips Essence 5000 Series
Shaverフィリップ ス 電 動シェーバーS5041/05品番取扱説明書保証書付保 証 書 は 、こ の 取 扱 説 明 書 の 最 終ページについておりますので販売店で 記 入を 受け てください 。 …
Essence 5000 Series 44
Additional Information:
Popular Right Now:
Operating Impressions, Questions and Answers:
ENGLISH HK 980 Integrated Amplifier OWNER’S MANUAL Table of Contents 3 Introduction 4 Connections DECLARATION OF CONFORMITY 5 Controls and Functions 6 Remote Control 7 Operating Instructions 7 Troubleshooting 8 Specifications We, Harman Consumer Group International 2, route de Tours F-72500 Château-du-Loir France declare in own responsibility, that the product described in this owners manual is in compliance with technical standards: EN 55013:2001 + A1:2003 EN 55020:2002 + A1:2003 EN 61000-3-2:2000 EN 61000-3-3:1995 + A1:2001 EN 60065:2002 Jurjen Amsterdam Harman Consumer Group International 12/07 2 TABLE OF CONTENTS Congratulations on your choice of the Harman Kardon HK 980 Integrated Amplifier. In order to obtain the best performance from this integrated amplifier, please be sure to read this owner's manual and use your integrated amplifier only in accordance with its instructions. The special features of this unit include: HCC (High Instantaneous Current Capability) The amplifier sections react rapidly to musical transients, providing the instantaneous current necessary to precisely drive and control nearly any loudspeaker system. Ultrawide Bandwidth The bandwidth of this unit is exceptionally wide and is independent of negative feedback. This improves transient accuracy and phase linearity. Low Negative Feedback This unit has been designed to have low distortion and wide bandwidth without high negative feedback. This further improves its dynamic accuracy. General instructions Always Use at 230V AC This unit is designed for operation with 230V AC. Use only domestic AC outlets. Connecting the unit to an outlet supplying a higher voltage may create a fire hazard. Handle the Power Cord Gently Do not disconnect the plug from the AC outlet by pulling the cord; always pull the plug itself. Pulling the cord may damage it. If you do not intend to use your unit for any considerable length of time, turn the unit off completely by taking the power cord out of the AC wall outlet. Do not place furniture or other heavy objects on the cord, and try to avoid dropping heavy objects on it. Also do not tie a knot in the power cord. Not only may the cord be damaged, it can also cause a short circuit with a consequent fire hazard. Place of installation Place the unit on a firm and level surface. Avoid installing your unit under the following conditions: Discrete Component Circuitry In order to achieve the above goals, all discrete electronic circuitry has been employed. No available integrated circuits could provide this high level of performance. ■ Moist or humid places. Sophisticated Electronic Protection Circuitry Harman Kardon's unique protection circuitry guards the amplifier from short circuit or damaged speakers and wires, without impairing sound quality by the use of current limiting or output relays. ■ Places subject to excessive vibration or dust. ■ Places exposed to direct sunlight or close to heating equipment. ■ Extremely cold locations. ■ Poorly ventilated places. Provide sufficient ventilation, do not block ventilation openings. Do not obstruct the ventilation slots on the top surface of the unit by placing objects on them. Otherwise, the temperature inside the unit may rise, possibly affecting its long-term reliability. To ensure sufficient ventilation, the product should be placed in an open area with free air flow. Do not place a CD player or other equipment on top of the amplifier. Do not expose the amplifier to dripping or splashing. Do not place objects filled with liquids, such as vases, on or near the amplifier. Moving the Unit Before moving the unit, be sure to pull out the power cord from the AC outlet and disconnect the interconnection cords with other units. Do Not Open the Cabinet To prevent shock hazard, do not tamper with internal components for inspection or maintenance. Harman Kardon does not guarantee against performance degradation resulting from any modification. If water, a hairpin or wire accidentally enters the unit, immediately pull the plug from the AC outlet to prevent shock and consult an authorized Harman Kardon service station. If you use the unit under this condition, it may cause a fire shock hazard. Cleaning If the unit gets dirty, wipe it with a soft dry cloth. If necessary, wipe it with a soft cloth dampened with mild soapy water and then with a dry cloth. Never use benzene, thinner, alcohol or other volatile agents, and avoid spraying an insecticide near the unit. Warning Signs If you detect an abnormal smell or smoke, immediately turn the amplifier off and unplug the power cord. Contact your dealer or nearest Harman Kardon service center. Packaging Save all packing material. It is essential for shipping, should you move, or in the event the unit ever needs repair. INTRODUCTION 3 ENGLISH Introduction Connections Speaker System 1 Right channel CD Recorder Cassette Tape Deck Record Player Speaker System 1 Left channel To wall outlet Right channel Speaker System 2 Left channel Speaker System 2 External Power Amp Video Player 2 Connecting Other Components 1. Make sure your amplifier and other components are turned off. 2. Connect each component's Output/Play jacks to the corresponding Input jacks on the back of your amplifier and, if available, the component’s Input/Record jacks to the Output jacks of the HK 980. Use the white, black or gray plugs to connect Left channel jacks; use the red plugs for Right channel jacks. 3. A record player with MM cartridge must be connected to the Phono Input jacks and a separate ground wire to the ground terminal screw above. Wired Remote Control To control your amplifier with an external infrared remote sensor, connect the wire from the remote sensor to the REMOTE IN jack on the back panel. Or, if another stereo component has a built-in infrared remote sensor and a Remote Output jack, it may be possible to connect this jack to the REMOTE IN jack of your amplifier. All Harman Kardon products with »Remote In« and »Remote Out« jacks are compatible with one another, except for the Citation 22, 24 and 25. Other manufacturers' remote sensors and components may not be compatible, but it will not hurt to experiment. A second wire may be used to connect your amplifier's REMOTE OUT jack to the Remote Input of another stereo component. 4 CONNECTIONS Video Player 1 Tuner Continue this process to include additional components (if compatible). Connecting Speakers 1. For best performance, use high quality speaker cables. However, ordinary copper wire can be used if the gauge meets the following requirements: Wire Length Up to 2.5 meter Up to 4 meter Up to 6 meter Above 6 meter Min. Diameter 1 mm 1.25 mm 1.6 mm 2-2.5 mm 2. Avoid rolling excess wire with or near signal interconnects. External Power Amplifiers For applications where higher power is desired, connect the Pre-Out Jacks to the Main In Jacks of an external power amplifier. Compact Disc Player IMPORTANT: When connecting two pairs of speakers, determine the impedance of each pair by looking on the back of the speakers, in your owner's manual, or by contacting your dealer or manufacturer. You can listen to two pairs of speakers at the same time ONLY if the impedance of EACH speaker is NOT LESS THAN 8 Ohms. WARNING: Do not play sets of speakers simultaneously except as recommended above. Amplifier may overheat. AC Power Plug the cord into a 230 VAC wall socket. Power indicator will light up to indicate power ON. To completely disconnect the power input, the main plug must be disconnected from the mains. 1 Power Indicator: This LED will illuminate in amber when the unit is in the Standby mode to signal that the unit is ready to be turned on. When the unit is in operation, the indicator will turn blue. 2 System Power Control: Press this button to turn on the HK 980; press it again to turn the unit off (to Standby). Note that the Power Indicator 1 next to the switch will turn blue when the unit is on. 3 Speaker 1 /2 Selectors: Press to select speaker pair 1 or 2, or both, or neither (headphone output only). 4 Input Source Selector: Select desired input source for listening by press-ing the ”Input Source” button repeatedly (on the left will select downwards, right upwards) until the display for the desired source is illuminated. 5 Record Source Selector: Select desired source for recording to device connected to the rear panel Tape and CDR Out sockets by pressing the ”Record Source” button repeatedly until the display for the desired source is illuminated. 6 Source Direct: Press to bypass tone control circuitry. 8 Headphone Jack: Plug in headphones if desired. With both ”Speaker 1” and ”2” selectors in the Off position, output is supplied only to headphones. 9 Volume Control: Turn to raise or lower output volume. ) Main Information Display: This display delivers messages and status indications to help you operate the receiver. ! Remote Sensor Window: The sensor behind this window receives infrared signals from the remote control. Aim the remote at this area and do not block or cover it unless an external remote sensor is installed. 7 Mode Button: Press this button to make changes to the bass, treble and balance settings. CONTROLS AND FUNCTIONS 5 ENGLISH Controls and Functions Remote Control Independent Remote Control The system remote of the HK 980 can control the amplifier and compatible Tuners, CD Players and CD Recorders. The remote In jack of units without an integrated IR receiver must be connected to the amplifier's remote control output jack so that the system remote control can operate them. The Function Table below will show all functions of the HK 980 and external devices that can be controlled by the HK 980 remote. Important Notes: • To remote control a tuner, CD Recorder or CD Player, the appropriate input (”TUNER”, ”CDR” or ”CD”) must have been selected with the source buttons of the remote control (selecting on the front panel is not sufficient). • Note that DVD players or tape decks cannot be controlled by the remote. • To control a compatible CD Recorder ”CDR” must be selected as input and the drive to be controlled (CDP or CDR) must be selected appropriately with the ”CDP SELECT” or ”CDR SELECT” buttons. Operating Conditions The control unit operates effectively within a distance of 7 meters and an angle of 30° from the amplifier. Using the control near fluorescent lights may shorten this range, as will any dust or dirt that accumulates on the front of the remote control or the remote sensor area of the amplifier. Also avoid blocking the line of sight between amplifier and remote. The control unit is powered by two AA batteries, included with your amplifier. When you replace weak batteries, replace both at the same time. When the remote is to be unused for an extended period, remove the batteries to prevent damage from corrosion. Remote button functions Button ON OFF Tuner Phono TV Tape Aux CD Volume + CDR 10+ Mode Folder + 10Volume Folder Previous JH I Play/Pause Next IK Search HH A Stop Search II Open/Close Scroll + Repeat Random Scroll 0 ~ 9 (Numeric Keys) Auto FM Mode RDS Mute Band Select HK 980 Power On Power Off Select Tuner Select Phono Select TV Select Tape Select Aux Select CD Volume Up Select CDR Select Mode Volume Down Mute Sound - CD Player Tuner Power Off Power Off Power On Power On Current Track +10 Next Folder Current Track -10 Previous Folder Skip Previous Play/Pause Skip Next Fast Reverse Stop Fast Forward Open/Close Tuning Up Repeat Play Random Play Tuning Down Track Select Preset Select Auto Tune FM Mode Select RDS Display Select Band Select Tune Mode Select HK 980 6 REMOTE CONTROL Listening to your CD player, tape deck, tuner or other source 1. Turn Volume control to minimum level and press the flat Power switch to turn on the amplifier. The power indicator lights blue and the protection circuitry checks for short circuit or other problems for a few seconds before sound output. 2. Press ”Speaker 1” to hear loudspeakers connected to the rear Speakers 1 terminals. Press ”Speaker 2” to hear loudspeakers connected to the rear Speakers 2 terminals. Press both to hear both speaker pairs at once. To listen to headphones only, press to turn off any active speaker pair. 3. Select desired source for listening by pressing the front panel Source up or down repeatedly until the name of the source is shown in the Main Information Display or by pressing the desired Source button on the remote control. 4. Begin playing the desired source. 5. Adjust the Volume control to the desired level. 6. Adjust Bass, Treble and Balance controls as desired (the Source Direct function must be turned off). To adjust the bass level, press the Mode Button twice so that the Main Information Display shows BASS 0dB. By turning the Volume Button to the right, the bass level will increase, turning the Volume Button left will decrease the bass level. Once the desired bass level has been set, press the Mode Button to set the requested level for the treble. The Main Information Display will show TREBLE 0dB. By turning the Volume Button to the right, the treble level will increase, turning the Volume Button left will decrease the treble level. Once the desired treble level has been set, press the Mode Button to set the requested level for the balance. The Main Information Display will show BALANCE 0. By turning the Volume Button to the right, the balance will move to the right speaker, turning the Volume Button left will move the balance to the left speaker. Press the Mode Button again to return the the normal volume indication. 7. Press ”Source Direct” until the the Main Information Display shows DIRECT ON to bypass the tone control to ensure purest sound performance. Press again to turn the bypass function off and to make the tone and balance controls function again. Making a recording You may record any source to tape or to CD-R or to both simultaneously. You may also connect a second tape deck to the CDR inputs and outputs to record from tape to tape (in either direction). To select the desired source for recording (this can be a different source than the one being listened to), press the Record Source Selector up or down button on the front panel repeatedly until the indicator for the name of the source to be recorded is shown in the Main Information Display. NOTE: The record output signal is taken directly from the program source and is unaffected by the Volume, Bass, Treble or Balance controls. Important Notes: • The functions ”Source Direct” and ”Record Source” can be selected on the front panel only, not from the remote control. • 3-head cassette decks with monitoring function can be connected to ”Tape” or ”CDR” connectors too, but their monitoring function cannot be used. Troubleshooting This unit is designed for trouble-free operation; most problems users encounter are due to operating errors. So if you have a problem, first check this list for a possible solution. If the problem persists, consult your authorized Harman Kardon service center. If the problem is... No lights illuminate when power cord is plugged into AC outlet. Make sure that... • The unit is plugged into a live outlet. No sound is heard. • Speaker switches corresponding to the desired speakers are pressed. • Correct source button has been pressed. • Volume is turned up. • Speaker wires are connected properly. • Hook-up wires to source component are connected properly. Sound is not heard from the speaker system on one side. • The speaker wires and connection wires are connected correctly. • Set the balance setting to 0 When listening to stereo sound, the left and right sounds are reversed. • The speaker wires are connected correctly. • The wires between components are connected correctly. Intermittent or continuous buzzing or hissing. • The unit is away from fluorescent lights, TV, motors and other electrical appliances. The remote control and front panel controls don't appear to work. • Disconnect the AC line cord from the wall socket, wait 5 minutes and then re-connect it. Humming noise when listening to LP • Ground wire from record player has been connected to ground terminal on amplifier. • Cable from record player is away from power cords and speaker cables. • Record player is not to close to speakers. • Record player is on stable surface. • Cable from record player is connected to the Phono jacks. • The phono cartridge is MM, not MC. Howl or ringing when listening to LP. Low sound level when listening to LP. OPERATING / TROUBLESHOOTING 7 ENGLISH Operating Instructions Specifications Continuous Average Power Per Channel (FTC) 20 Hz – 20 kHz, both channels driven 8 Ohms: 4 Ohms: NOMINAL 80 [email protected]<0.09%THD 120 [email protected]<0.3%THD Dynamic Power (IHF, 1 kHz Tone Burst) 8 Ohms: 4 Ohms: 2 Ohms: 1 Ohms: 115 Watts 200 Watts 295 Watts 380 Watts High instantaneous current capability (HCC) ±80 Amps Power Bandwidth @ Half-Rated output, 8 <10 Hz - 150 kHz Frequency response @ 1W (+0/-3dB) 5 Hz - 150 kHz Damping factor (20Hz-20k Hz) >125 Signal-to-noise Ratio (Reference rated power output, A-WTD) Tuner/CD Phono (MM): 95 dB 75 dB Input sensitivity/Impedance Tuner/CD Phono (MM): 270mV/43k Ohms 4.0mV/47k Ohms Overload: Tuner/CD Phono (MM): 4V 90 mV Tone control range, Bass @ 50 Hz/Treble @ 10 kHz ±10 dB/±10 dB Power supply: AC 230V, 50 Hz Power consumption: 410 W Dimensions (Width x Height x Depth): 440 x 116 x 392 mm Weight: 12.7 kg 250 Crossways Park Drive, Woodbury, New York 11797 www.harmankardon.com Harman Consumer Group International: 2, Route de Tours, 72500 Château-du-Loir, France © 2007 Harman Kardon, Incorporated Part no. 8543 4813 0101