Hunter eco logic автополив инструкция

Eco-Logic

4-& 6-Station Indoor Controller

Owners Manual and Programming Instructions

Weather Sensor

Installation Instructions

Remove lower access cover. Place a screw into the wall and hang the controller from the

keyhole on the back. Secure the controller using one or more screws below the terminal

strip. One wire from each solenoid should be connected to the C terminal (common wire).

The other wire from each solenoid to its respective number on the terminal strip. Connect

the transformer wires to the 24 VAC terminal strip. Attach the two sensor wires (if needed)

to the SEN terminals. Connect a 9-volt alkaline battery (not included) to the battery wire

clip. Plug the transformer into a nearby power outlet.

Main Display

Current Time/Day – Set current day and time.

Start Times – Set 1 to 4 start times for each program.

Run Times – Set each valve station run time from 1 min. to 4 hrs.

Water Days – Select specific days to water, odd/even days, or a selected number

of days between waterings (interval).

Seasonal Adjustment – Make run time changes according to the seasons without

reprogramming the controller.

System Off – Stops all automatic watering.

Program Designator – identifies program in use (A or B).

Flashing Sprinkler – indicates that watering is occurring.

Umbrella – indicates rain sensor is suspending irrigation.

Crossed Umbrella – Indicates rain sensor has been manually bypassed.

– identifies month when programming current date.

– identifies day when programming current date.

Manual Single Station – indicates the one time watering of a single valve station.

1

Manual All Station – indicates the one time watering of all valve stations or selected

stations.

System Off

Seasonal

Adjustment

A

B

Water Days

Control Buttons

Button – increases displayed item.

Button – decreases the displayed item.

Button – advances to the next item.

Button – advances to the previous item.

Button – Select program A or B for different watering requirements.

Mode Button – Advanced through programming functions.

Programming the Controller

An irrigation program consists of three parameters:

1) A program start time, 2) watering duration for each station and 3) days to water. A

program will run all stations assigned to it in sequential order. Programs are independent

and stations can be assigned to both programs.

Setting the Current Date and Time

1. Press the

Mode button until the arrow is pointing at the Current Time/Day

position.

2. The year will be flashing. Use the

button to proceed to setting the month.

3. The month will be flashing and the

buttons to change the month. Press the

4. The day will be flashing and the

tons to change the day. Press the

5. The time will be displayed. Use the

24 hour. Press the

button to set the hour.

MasterValve

%

AM

PM

24

RST

SEN

C

MV

1

2

3

4

5

6

24VAC

9 VOLT

ALKALINE

BATTERY

24VAC

Current

Time/Day

%

AM

PM

Start Times

24

1

Run Times

or

buttons to change the year. Press the

icon will be displayed. Use the

button to proceed to setting the day.

icon will be displayed. Use the

button to proceed to setting the time.

and

buttons to select AM, PM, or

6. Hours will be flashing. Use the

the

button to move to minutes.

7. Use the

and

have now been set.

Valve 4

Setting the Program Start Time(s)

Valve 3

NOTE: One start time will activate all stations sequentially in that program. This

eliminates the need to enter each station’s start time. Multiple start times in a

Valve 2

program can be used for separate morning, afternoon, or evening watering cycles.

Valve 1

1. Press the

2. Program A will be displayed. (If Program B is desired, press the

3. Use the

or

4. Press the

button to add an additional start time, or

program.

Eliminating a Program Start Time

With the arrow pointing at the Start Times position, press the

you reach 12:00 AM. Push the

Setting Station Run Times

1. Press the

2. Use the

button to select a program (A or B).

3. Press the

or

Press the

button to advance to the next station.

Setting Days to Water

1. Press the

2. Use the

button to select the desired program.

3. Arrows point at the specific days of the week in which watering is to occur. Press

the

button to activate that day or the

Selecting Odd or Even Days to Water

This feature is uses numbered days of the month for watering instead of specific days

of the week (Odd days 1st, 3rd, 5th, etc.; Even days 2nd, 4th, 6th, etc.).

1. When in the Water Days mode, press the

either ODD or EVEN on the display.

2. Press the

button to select, or the

to water.

Selecting Interval Watering

You can select interval watering from 1 to 31 days.

1. When in the Water Days mode, press the

Press the

button and the interval watering icon

a 1 will be flashing.

2. Press the

or

(1 to 31 days). This is called the interval.

The controller will water the selected program at the next start time and will then

water at the interval programmed.

Seasonal Adjustment

Seasonal Adjustment is used to make global run time changes without re-program-

ming the entire controller.

1. Press the

2. Press the

or

from 10% to 150%.

NOTE: The controller should always be initially programmed in

the 100% position.

System Off

To turn your controller off, press the

the System Off

watering will be shut off. All active programs will be discontinued and watering

stopped. To return the controller to normal automatic operation, simply press the

Mode button once. The current time and day will be displayed.

Programmable Off

This feature will stop all programmed waterings for a designated period of time from

1 to 7 days. After the programmed off period, the controller will automatically resume

or

programmed watering.

1. Press the

or

but-

function.

2. Wait 2 seconds until OFF is displayed.

3. Press the

button to set the number of days off (up to 7 days).

and

buttons to change the hour shown. Press

buttons to change the minutes shown. The date, day and time

Mode button until the arrow is pointing at Start Times

buttons to change the start time.

button once to reach the OFF position.

Mode button until the arrow is pointing at Run Times

buttons to change the station run time from 1 minute to 4 hours.

Mode button until the arrow is pointing at Water Days

button to cancel watering for that day.

button until the cursor is above

button to cancel either ODD or EVEN days

button until the cursor is over INT.

button to select the number of days between watering days

Mode button until the arrow is pointing at Seasonal Adjustment

buttons to adjust the percentage of the seasonal adjustment

Mode button until the arrow is pointing at

. Wait 2 seconds and the display will read OFF. Valves currently

Mode button until the arrow is positioned next to the System Off

.

button).

button for the next

or

buttons until

.

.

will be displayed and

.

Предложите, как улучшить StudyLib

(Для жалоб на нарушения авторских прав, используйте

другую форму
)

Таймер автоматического полива Hunter Eco Logic идеально подходит для установки на небольшие приусадебные участки и управления автополивом.

Инструкция по настройке

Посмотрите видео инструкцию, как настраивать конторллер

Почему таймер ECO LOGIC подойдет именно вам

Невысокая цена, высокий функционал автоматического таймера для полива, легкая программируемость, широкий выбор настроек. Все это вы получаете приобретая пульт ECO LOGIC.

Пульт управления превосходно работает в паре с насосом Espa Tecnopres 25 4m.

Фирма Hunter специально разработала данный вид пультов, чтобы владельцы любых участков, даже с небольшим бюджетом, могли установить себе систему автоматического полива.

Как происходит настройка

Всего 1 раз вы настраиваете систему и целый год наслаждаетесь результатами ее работы.

За все это отвечает компьютер, безошибочно точно распределяющий расход воды в системе орошения.

Hunter — фирма из США, давно зарекомендовавшая себя на рынке поливочного оборудования.

Существует альтернативный автоматический контроллер полива RZX-4i от Rain Bird

Гарантия

Гарантия на все устройства и механизмы составляет 2 года с момента установки.

Таймеры Eco Logic расчитаны на 4 или 6 зон. Устанавливать пульт нужно в помещении.

Как экономить свое время и силы

Если вам требуется внешний контроллер, обратитесь к пульту управления X-Core

Установите систему автополива на своем участке и дайте растениям возможность расти без вашего участия — экономьте 100% своего времени затрачиваемого на орошение.

Звоните сейчас или оставьте заявку на сайте. Наш менеджер ответит на все ваши вопросы и даст подробную консультацию.

Получите бесплатно расчет стоимости системы автоматического полива сейчас.

Eco-Logic 4-& 6-Station Indoor Controller
Owners Manual and Programming Instructions
Weather Sensor
MasterValve
6. Hours will be flashing. Use the and
the
button to move to minutes.
7. Use the and buttons to change the minutes shown. The date, day and time
have now been set.
%
AM
PM
24
Valve 4
Setting the Program Start Time(s)
Valve 3
RST
24VAC
SEN
C MV 1
buttons to change the hour shown. Press
2
3
4
5
NOTE: One start time will activate all stations sequentially in that program. This
eliminates the need to enter each station’s start time. Multiple start times in a
program can be used for separate morning, afternoon, or evening watering cycles.
6
9 VOLT
ALKALINE
BATTERY
Valve 2
24VAC
Valve 1
Mode button until the arrow is pointing at Start Times
1. Press the
2. Program A will be displayed. (If Program B is desired, press the
Installation Instructions
3. Use the
Remove lower access cover. Place a screw into the wall and hang the controller from the
keyhole on the back. Secure the controller using one or more screws below the terminal
strip. One wire from each solenoid should be connected to the C terminal (common wire).
The other wire from each solenoid to its respective number on the terminal strip. Connect
the transformer wires to the 24 VAC terminal strip. Attach the two sensor wires (if needed)
to the SEN terminals. Connect a 9-volt alkaline battery (not included) to the battery wire
clip. Plug the transformer into a nearby power outlet.
4. Press the
program.
Main Display
With the arrow pointing at the Start Times position, press the or buttons until
you reach 12:00 AM. Push the
button once to reach the OFF position.
Setting Station Run Times
Mode button until the arrow is pointing at Run Times
.
button to select a program (A or B).
Run Times – Set each valve station run time from 1 min. to 4 hrs.
3. Press the
Press the
or buttons to change the station run time from 1 minute to 4 hours.
button to advance to the next station.
Water Days – Select specific days to water, odd/even days, or a selected number
of days between waterings (interval).
Setting Days to Water
Seasonal Adjustment – Make run time changes according to the seasons without
reprogramming the controller.
2. Use the
1. Press the
Mode button until the arrow is pointing at Water Days
.
button to select the desired program.
3. Arrows point at the specific days of the week in which watering is to occur. Press
the button to activate that day or the button to cancel watering for that day.
System Off – Stops all automatic watering.
Program Designator – identifies program in use (A or B).
Flashing Sprinkler – indicates that watering is occurring.
Selecting Odd or Even Days to Water
Umbrella – indicates rain sensor is suspending irrigation.
This feature is uses numbered days of the month for watering instead of specific days
of the week (Odd days 1st, 3rd, 5th, etc.; Even days 2nd, 4th, 6th, etc.).
Crossed Umbrella – Indicates rain sensor has been manually bypassed.
– identifies month when programming current date.
– identifies day when programming current date.
1
button for the next
2. Use the
Start Times – Set 1 to 4 start times for each program.
buttons to change the start time.
button to add an additional start time, or
Eliminating a Program Start Time
1. Press the
Current Time/Day – Set current day and time.
or
.
button).
1. When in the Water Days mode, press the
either ODD or EVEN on the display.
Manual Single Station – indicates the one time watering of a single valve station.
2. Press the
to water.
Manual All Station – indicates the one time watering of all valve stations or selected
stations.
Selecting Interval Watering
System Off
Seasonal
Adjustment
Water Days
A
%
AM
PM
24
B 1
Current
Time/Day
Start Times
Run Times
Control Buttons
button to select, or the
button until the cursor is above
button to cancel either ODD or EVEN days
You can select interval watering from 1 to 31 days.
button until the cursor is over INT.
1. When in the Water Days mode, press the
Press the
button and the interval watering icon
will be displayed and
a 1 will be flashing.
2. Press the or button to select the number of days between watering days
(1 to 31 days). This is called the interval.
The controller will water the selected program at the next start time and will then
water at the interval programmed.
Seasonal Adjustment
Button – increases displayed item.
Button – decreases the displayed item.
Seasonal Adjustment is used to make global run time changes without re-programming the entire controller.
Button – advances to the next item.
1. Press the
Button – advances to the previous item.
2. Press the or
buttons to adjust the percentage of the seasonal adjustment
from 10% to 150%.
Button – Select program A or B for different watering requirements.
M ode Button – Advanced through programming functions.
Mode button until the arrow is pointing at Seasonal Adjustment
NOTE: The controller should always be initially programmed in
the 100% position.
Programming the Controller
An irrigation program consists of three parameters:
1) A program start time, 2) watering duration for each station and 3) days to water. A
program will run all stations assigned to it in sequential order. Programs are independent
and stations can be assigned to both programs.
Setting the Current Date and Time
1. Press the
position.
Mode button until the arrow is pointing at the Current Time/Day
2. The year will be flashing. Use the or buttons to change the year. Press the
button to proceed to setting the month.
3. The month will be flashing and the
icon will be displayed. Use the or
buttons to change the month. Press the
button to proceed to setting the day.
4. The day will be flashing and the
tons to change the day. Press the
icon will be displayed. Use the or butbutton to proceed to setting the time.
5. The time will be displayed. Use the and buttons to select AM, PM, or
24 hour. Press the
button to set the hour.
System Off
To turn your controller off, press the
Mode button until the arrow is pointing at
the System Off
. Wait 2 seconds and the display will read OFF. Valves currently
watering will be shut off. All active programs will be discontinued and watering
stopped. To return the controller to normal automatic operation, simply press the
Mode button once. The current time and day will be displayed.
Programmable Off
This feature will stop all programmed waterings for a designated period of time from
1 to 7 days. After the programmed off period, the controller will automatically resume
programmed watering.
1. Press the
function.
Mode button until the arrow is positioned next to the System Off
2. Wait 2 seconds until OFF is displayed.
3. Press the
button to set the number of days off (up to 7 days).
.
Automatic Watering
Hunter Quick Check Diagnostics
After all programming has been completed, press the
Mode button until the time of
day is displayed. This will enable automatic execution of all selected watering programs
and start times.
This feature allows you to quickly diagnose wiring problems with your controller.
Manual Run – All Stations
2. Press the button once to begin the Quick Check procedure. Within seconds the
system searches all stations, detecting any circuit problems. When a field wiring
short is detected, an ERR symbol preceded by the station number will flash momentarily on the display.
Manual All Stations allows the operation of valves assigned to a program in sequential order.
1. Press and hold the
button for three seconds. The
will be displayed, along with the
program letter. A station number will also be displayed.
button.
2. Select program by pressing the
3. Use the or buttons to select the amount of time for the station to water if
different from the run time displayed.
4. Use the
5. Repeat steps 3 and 4 until you reach the station at which you want
watering to begin.
After 2 seconds of inactivity, manual watering will begin and sequence through each
valve of the entire program. Once manual watering has been completed, the controller
will automatically return to the automatic mode with no change in the previously set
program.
1
Manual Single Station function allows the for operation of a single valve.
Sensor Bypass
The sensor can be bypassed to allow manual operation when the sensor has deactivated the system.
1. Press the
2. Press the
button for two seconds ON
will be displayed.
button to bypass the rain sensor. OFF
will be displayed.
Clearing the Controller’s Memory / Resetting the Controller
If you feel that you have misprogrammed your controller, there is a process that will
reset the memory to the factory defaults and erase all programs and data that have
been entered into the controller.
1. Press and hold the
,
, and
Normal/Limited Program Mode
Your controller can be programmed to increase or decrease the watering program
capability.
1. Press and hold the
2. Release the
button to move to the next station.
Manual Run – Single Station
1. Press the ,
,
,
buttons simultaneously. In the standby mode, the LCD
will display all segments.
buttons.
2. Press and release the reset button located in the lower wiring compartment.
,
, and
buttons. The display should now
3. Wait 2 seconds and release the
show 12:00 am. All programmed data has been cleared from memory and the
controller can now be reprogrammed.
button. Press the
and the
button.
buttons
or
button to change program modes:
3. Use the
Normal Mode (2 programs/4 start times)
Limited Mode (1 program/1 start time)
Advanced (3 programs/4 start times)
Operating Specifications
•
•
•
•
•
•
•
2 Independent Watering Programs
Station Run Time: 0 to 4 hours in 1-minute increments
Start Times: 4 per day, per program, for up to 12 daily starts
Watering Schedule: 365-day calendar, odd/even, or interval (1 to 31 days).
Simple manual operation
Seasonal adjustment (10% to 150%)
Programmable rain delay (1 to 7 days)
Electrical Specifications
•
•
•
•
•
•
•
Transformer input 230VAC 50/60 Hz
Transformer output: 24VAC .625 amp.
Station Output: .56 amp.
Battery 9-volt (not included) for backup timekeeping
Electronic short circuit protection
Non-volatile memory for program data
CE approved
Certificate of Conformity to European Directives
Hunter Industries declares that the irrigation controller Eco-Logic complies with
the standards of the European Directives of “electromagnetic compatibility”
87/336/EEC and “low voltage” 73/23/EEC.
__________________________________
Troubleshooting Guide
Project Engineer
PROBLEM
CAUSES
SOLUTIONS
Display indicates watering but none
is occurring.
Faulty or miswired valve.
Check valve and valve wiring.
Faulty pump or pump relay.
Check pump and pump relay. Replace if defective.
No water pressure to system.
Turn on main system water supply.
Unit has just been powered up for the first time.
Set time/date.
Extended power outage has occurred that has drained
backup battery.
Replace battery and reprogram controller.
Short in wire connections.
Check wiring for short or faulty wire connections.
Bad solenoid.
Replace solenoid.
Display shows “ERR” with a number (1-6).
Short in valve wiring circuit; or a faulty solenoid
on the station number indicated.
Check wire circuit or solenoid for the valve number indicated. Repair short
or replace solenoid. Press any button to clear “ERR” display.
Display shows “P ERR”.
Faulty pump relay or master valve wiring.
Check wiring to relay or master valve solenoid. Press any button to clear
“P ERR” from the display.
Time of day display is blinking.
Valve will not turn on.
Incompatible or defective pump relay.
Check electrical specifications of pump relay. Replace if defective.
The display reads “No AC”.
There is no AC power present.
Check to make sure power is on. Check to see if transformer is properly
installed.
Rain Sensor does not suspend irrigation.
Rain sensor is defective or miswired.
Verify operation of sensor and proper wiring.
Jumper not removed.
Remove jumper.
Frozen Display, or display showing incorrect
information.
Power surge.
Reset controller per “Clearing Controllers Memory/Resetting
the Controller”.
Automatic irrigation does not start at start time and
controller is not in the system off mode.
AM/PM of time of day not set correctly.
Correct AM/PM of time of day.
AM/PM of start time not set correctly.
Correct AM/PM of start time. Set start time.
Start time is disabled (Set for Off).
See “Setting Watering Start Times”.
Controller is not receiving AC power.
Check AC connections.
Too many start times entered in program (user error).
One start time activates a complete cycle. See “Setting Watering
Start Times”.
Controller waters the same area more than
one time/Controller cycles continuously.
Hunter Industries Incorporated • The Irrigation Innovators
Internet: www.HunterIndustries.com
INT-575
11/06

Was this manual useful for you?

Yes

No

Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project