Кадиллак хт5 инструкция по эксплуатации

Задать вопрос о Cadillac XT5 (2021)

XT5

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Keys, Doors, and Windows . . . . . . . . . . 9

Seats and Restraints . . . . . . . . . . . . . . . 44

Storage . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . 95

Instruments and Controls . . . . . . . . 102

Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143

Infotainment System . . . . . . . . . . . . . 150

Climate Controls . . . . . . . . . . . . . . . . . . 151

Driving and Operating . . . . . . . . . . . . 160

Vehicle Care . . . . . . . . . . . . . . . . . . . . . . . 250

Service and Maintenance . . . . . . . . . 335

Technical Data . . . . . . . .. . . . . . . . . . . . 349

Customer Information . . . . . . . . . . . . 353

Reporting Safety Defects . . . . . . . . . 363

OnStar ….. . . . . . . . . . . . . . . . . . . . . . . . . . 367

Connected Services . . . . . . . . . . . . . . . 374

Index . . . . . . . . . . . . . . . . . . . . . . . . 377

2 INTRODUCTION

Introduction

The names, logos, emblems, slogans,
vehicle model names, and vehicle
body designs appearing in this manual
including, but not limited to, GM, the
GM logo, CADILLAC, the CADILLAC
Emblem, and XT5 are trademarks and/
or service marks of General Motors
LLC, its subsidiaries, affiliates,
or licensors.

For vehicles first sold in Canada,
substitute the name “General Motors
of Canada Company” for Cadillac
Motor Car Division wherever it
appears in this manual.

This manual describes features that
may or may not be on the vehicle
because of optional equipment that
was not purchased on the vehicle,
model variants, country specifications,
features/applications that may not be
available in your region, or changes
subsequent to the printing of this
owner’s manual.

Refer to the purchase documentation
relating to your specific vehicle to
confirm the features.

Keep this manual in the vehicle for
quick reference.

Canadian Vehicle Owners

A French language manual can be
obtained from your dealer, at
www.helminc.com, or from:

Propriétaires Canadiens

On peut obtenir un exemplaire de ce
guide en français auprès du
concessionnaire ou à l’adresse
suivante:

Helm, Incorporated
Attention: Customer Service
47911 Halyard Drive
Plymouth, MI 48170
USA

Using this Manual

To quickly locate information about
the vehicle, use the Index in the back
of the manual. It is an alphabetical
list of what is in the manual and the
page number where it can be found.

Danger, Warning, and
Caution

Warning messages found on vehicle
labels and in this manual describe
hazards and what to do to avoid or
reduce them.

Danger

{

Danger indicates a hazard with a
high level of risk which will result
in serious injury or death.

Litho in U.S.A.
Part No. 84290261 A First Printing

©

2019 General Motors LLC. All Rights Reserved.

INTRODUCTION 3

Warning

{

Warning indicates a hazard that
could result in injury or death.

Caution

Caution indicates a hazard that
could result in property or vehicle
damage.

Symbols

The vehicle has components and
labels that use symbols instead of
text. Symbols are shown along with
the text describing the operation or
information relating to a specific
component, control, message, gauge,
or indicator.

M : Shown when the owner’s manual

has additional instructions or
information.

* : Shown when the service manual

has additional instructions or
information.

0 : Shown when there is more

information on another page —
“see page.”

Vehicle Symbol Chart

A circle with a slash through it is a
safety symbol which means “Do not,”
“Do not do this,” or “Do not let this
happen.”

Here are some additional symbols that
may be found on the vehicle and what
they mean. See the features in this
manual for information.

u : Air Conditioning System
G : Air Conditioning Refrigerant Oil
9 : Airbag Readiness Light

! : Antilock Brake System (ABS)
$ : Brake System Warning Light

9 : Dispose of Used Components

Properly

P : Do Not Apply High Pressure

Water

B : Engine Coolant Temperature
_ : Flame/Fire Prohibited
H : Flammable
[ : For ward Collision Alert
R : Fuse Block Cover Lock Location
+ : Fuses
j : ISOFIX/LATCH System Child

Restraints

Q : Keep Fuse Block Covers Properly

Installed

| : Lane Change Alert
@ : Lane Departure Warning
A : Lane Keep Assist

* : Malfunction Indicator Lamp
: : Oil Pressure

X : Park Assist

4 INTRODUCTION

~ : Pedestrian Ahead Indicator

O : Power

7 : Rear Cross Traffic Alert

I : Registered Technician

/ : Remote Vehicle Start

> : Seat Belt Reminders

I : Side Blind Zone Alert

h : Stop/Start

7 : Tire Pressure Monitor

d : Traction Control/StabiliTrak/

Electronic Stability Control (ESC)

a : Under Pressure
V : Vehicle Ahead Indicator

Instrument Panel Overview

INTRODUCTION 5

6 INTRODUCTION

1. Air Vents 0 158.

2. Exterior Lamp Controls 0 143.

Turn Signal Lever. See Turn and
Lane-Change Signals 0 147.

IntelliBeam System Button (If
Equipped). See Exterior Lamp
Controls 0 143.

3. Tap Shift Controls. See Manual
Mode 0 191.

4. Instrument Cluster 0 111.

Driver Information Center (DIC)
Display. See Driver Information
Center (DIC) 0 127.

5. Windshield Wiper/Washer 0 104.

Rear Window Wiper/Washer

0 106.

6. ENGINE START/STOP Button.
See Ignition Positions 0 176.

7. Park Assist Button. See

Assistance Systems for Parking or
Backing 0 211.

Automatic Parking Assist (APA)
Button. See Assistance Systems

for Parking or Backing 0 211.

Stop/Start System 0 179 Disable

Button.

8. Light Sensor. See Automatic
Headlamp System 0 145.

9. Hazard Warning Flashers 0 146.

10. Infotainment 0 150.

11. Heated and Ventilated Front Seats
0 51 (If Equipped).

12. MODE Switch. See Driver Mode

Control 0 198.

Traction Control/Electronic
Stability Control 0 196.

All-Wheel Drive 0 192 (If

Equipped).

13. Dual Automatic Climate Control
System 0 151.

14. Wireless Charging 0 108 (If
Equipped).

15. Infotainment 0 150.

16. Shift Lever. See Automatic
Transmission 0 186.

17. Steering Wheel Controls 0 103.

Driver Information Center (DIC)
Controls. See Driver Information
Center (DIC) 0 127.

18. Steering Wheel Controls 0 103.

19. Horn 0 103.

20. Forward Collision Alert (FCA)

System 0 220 (If Equipped).

Lane Keep Assist (LKA) 0 231 (If

Equipped).

Heated Steering Wheel 0 103 (If
Equipped).

21. Cruise Control 0 199.

Adaptive Cruise Control 0 201 (If
Equipped).

Phone Button. See Steering Wheel
Controls 0 103.

22. Steering Wheel Adjustment 0 103

(Out of View).

23. Head-Up Display (HUD) 0 130 (If

Equipped).

24. Hood Release. See Hood 0 253.

Data Link Connector (DLC) (Out
of View). See Malfunction

Indicator Lamp (Check Engine
Light) 0 118.

25. Instrument Panel Illumination
Control 0 147.

26. Electric Parking Brake 0 194.

INTRODUCTION 7

8 INTRODUCTION

2 NOTES

Keys, Doors, and
Windows

Keys and Locks

Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Remote Keyless Entry (RKE)

System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Remote Keyless Entry (RKE)

System Operation . . . . . . . . . . . . . . . . 10
Remote Vehicle Start . . . . . .. . . . . . . . 17
Door Locks . . . . . . . . . . . . … . . . . . . . . . . 18
Power Door Locks . . . . . . . . . . . . . . . . . 21
Delayed Locking . . . . . . . .. . . . . . . . . . . 21
Automatic Door Locks . . . . . . . . . . . . 21
Lockout Protection . . . . . . . . . . . . . . . . 22
Safety Locks . . . . . . . . . . . . . . . . . . . . . . . . 22

Doors

Liftgate . . . . . . . . . . . . . . . … . . . . . . . . . . . 23

Vehicle Security

Vehicle Security ………. . . . . . . . . . . 31
Vehicle Alarm System . . . . . . . . . . . . . 31
Steering Column Lock . . . . . . … . . . . 32

Immobilizer ….. . . . . . . . . . . .. . . . . . . . 33
Immobilizer Operation . . . . . . . . . . . . 33

Exterior Mirrors

Convex Mirrors . . . . . . . . . . . . . . . . . . . . 34
Power Mirrors . . . . . . . . . . . . . . . . . . . . . . 35
Folding Mirrors . . . . . . . . . . . . . . . . . . . . 35
Heated Mirrors . . . . . . . . . . . . . . . . . . . . . 36
Automatic Dimming Mirror . . .. . . . 36
Reverse Tilt Mirrors . . . . . . . . . . . . . . . 36

Interior Mirrors

Interior Rearview Mirrors . . . . . . . . . 37
Manual Rearview Mirror . . . . . . . . . . 37
Automatic Dimming Rearview

Mirror . . . . . . . . ……. . . . . . . . . . . . . . . 37

Rear Camera Mirror …. . . . . . . . . . . . 37

Windows

Windows . . . . . . . . . . .. . . . . . . . . . . . . . .. 39
Power Windows . . . . . . . . . . . . . . . . . . . . 40
Sun Visors . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Roof

Sunroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

KEYS, DOORS, AND WINDOWS 9

Keys and Locks

Keys

Warning

{

Leaving children in a vehicle with a
Remote Keyless Entry (RKE)
transmitter is dangerous and
children or others could be
seriously injured or killed. They
could operate the power windows
or other controls or make the
vehicle move. The windows will
function with the RKE transmitter
in the vehicle, and children or
others could be caught in the path
of a closing window. Do not leave
children in a vehicle with an RKE
transmitter.

10 KEYS, DOORS, AND WINDOWS

To remove the key, press the button
on the side of the transmitter, near
the bottom, and pull the key out.
Never pull the key out without
pressing the button.

If it becomes difficult to turn the key,
inspect the key blade for debris.
Periodically, clean with a brush or
a pick.

See your dealer if a new key is needed.

Contact Roadside Service if locked out

The key, inside the Remote Keyless
Entry (RKE) transmitter, can be used
for all locks.

of the vehicle. See Roadside Service
0 357.

With an active OnStar or connected
service plan, an OnStar Advisor may
remotely unlock the vehicle. See
OnStar Overview 0 367.

Remote Keyless Entry
(RKE) System

See Radio Frequency Statement 0 363.

If there is a decrease in the Remote
Keyless Entry (RKE) operating range:

.

Check the distance. The
transmitter may be too far from
the vehicle.

.

Check the location. Other vehicles
or objects may be blocking the
signal.

.

Check the transmitter’s battery.
See “Battery Replacement” later in
this section.

.

If the transmitter is still not
working correctly, see your dealer
or a qualified technician for
service.

Remote Keyless Entry
(RKE) System Operation

The Keyless Access system allows for
vehicle entry when the Remote
Keyless Entry (RKE) transmitter is
within 1 m (3 ft). See “Keyless Access
Operation” following.

The RKE transmitter functions may
work up to 60 m (197 ft) away from
the vehicle.

Other conditions can impact the
performance of the transmitter. See

Remote Keyless Entry (RKE) System
0 10.

Q : Press to lock all doors and if

equipped, the fuel door. The turn
signal indicators may flash and/or the
horn may sound on the second press
to indicate locking. See Vehicle
Personalization 0 134.

If the driver door is open when
pressed and Open Door Anti-Lockout
is enabled, all doors will lock and then
the driver door will immediately
unlock. See Vehicle Personalization
0 134. If the passenger door is open

when

Q is pressed, all doors lock.

Q is

Pressing
theft-deterrent system. See Vehicle
Alarm System 0 31.

If equipped with remote folding
mirrors, press and hold
one second to fold the mirrors,
if enabled. See Folding Mirrors 0 35.

Q may also arm the

Q for

K : Press to unlock the driver door

and if equipped, the fuel door. Press
unlock again within five seconds to
unlock all doors. The RKE transmitter
can be programmed to unlock all
doors on the first button press. See
Vehicle Personalization 0 134. The turn
signal indicators may flash to indicate
unlocking. See Vehicle Personalization
0 134. When remotely unlocking the
vehicle at night, the lights come on
briefly to light your approach to the
vehicle.

Pressing
theft-deterrent system. See Vehicle
Alarm System 0 31.

K will disarm the

KEYS, DOORS, AND WINDOWS 11

If equipped with remote folding
mirrors, press and hold
one second to unfold the mirrors,
if enabled. See Folding Mirrors 0 35.

If equipped with remote windows,
press and hold
fully open, if enabled. See Vehicle
Personalization 0 134.

K until the windows

K for

/ : Press and release Q and then

immediately press and hold
least four seconds to start the engine
from outside the vehicle using the
RKE transmitter. See Remote Vehicle
Start 0 17.

/ for at

7 : Press and release one time to

initiate vehicle locator. The exterior
lamps flash and the horn chirps three

times. Press and hold
three seconds to sound the panic
alarm. The horn sounds and the turn
signal lamps flash for 30 seconds,

or until
vehicle is started.

7 is pressed again or the

7 for

12 KEYS, DOORS, AND WINDOWS

b : Press twice quickly to open or

close the liftgate.

Press once to stop the liftgate from
moving.

Keyless Access Operation

With the Keyless Access system, you
can lock and unlock the doors and
access the liftgate without removing
the RKE transmitter from your pocket,
purse, briefcase, etc. The RKE
transmitter should be within 1 m (3 ft)
of the liftgate or door being opened.

Keyless Access can be programmed to
unlock all doors on the first lock/
unlock press from the driver door. See
Vehicle Personalization 0 134.

If equipped with memory seats, RKE
transmitters 1 and 2 are linked to
seating positions of memory 1 or 2.
See Memory Seats 0 48.

Keyless Unlocking/Locking from the
Driver Door

When the doors are locked and the
RKE transmitter is within 1 m (3 ft) of
the driver door handle, pressing the
lock/unlock button on the driver door

handle will unlock the driver door.
If the lock/unlock button is pressed
again within five seconds, all
passenger doors will unlock.

Driver Shown, Passenger Similar

Pressing the lock/unlock button will
cause all doors to lock if any of the
following occur:

.

It has been more than five seconds
since the first lock/unlock button
press.

.

Two lock/unlock button presses
were used to unlock all doors.

.

Any vehicle door has opened and
all doors are now closed.

Keyless Unlocking/Locking from
Passenger Doors

When the doors are locked and the
RKE transmitter is within 1 m (3 ft) of
the door handle, pressing the lock/
unlock button on that door handle
will unlock all doors. Pressing the
lock/unlock button will cause all doors
to lock if any of the following occur:

.

The lock/unlock button was used
to unlock all doors.

.

Any vehicle door has opened and
all doors are now closed.

Passive Locking

This vehicle will lock several seconds
after all doors are closed if the vehicle
is off and at least one RKE transmitter
has been removed or none remain in
the interior.

If equipped, the fuel door will lock.

If other electronic devices interfere
with the RKE transmitter signal, the
vehicle may not detect the RKE
transmitter inside the vehicle.
If passive locking is enabled, the doors
may lock with the RKE transmitter

inside the vehicle. Do not leave the
RKE transmitter in an unattended
vehicle.

To customize the doors to
automatically lock when exiting the
vehicle, see Vehicle Personalization
0 134.

Temporary Disable of Passive
Locking

Temporarily disable passive locking by
pressing and holding

interior door switch with a door open
for at least four seconds, or until three
chimes are heard. Passive locking will

then remain disabled until
interior door is pressed, or until the
vehicle is turned on.

Remote Left in Vehicle Alert

When the vehicle is turned off and an
RKE transmitter is left in the vehicle,
the horn will chirp three times after
all doors are closed. To turn on or off,
see Vehicle Personalization 0 134.

K on the

Q on the

Remote No Longer in Vehicle Alert

If the vehicle is on with a door open,
and then all doors are closed, the
vehicle will check for RKE
transmitters inside. If an RKE
transmitter is not detected, the Driver
Information Center (DIC) will display
NO REMOTE DETECTED and the horn
will chirp three times.

This occurs only once each time the
vehicle is driven.

To turn on or off, see Vehicle
Personalization 0 134.

Keyless Liftgate Opening

Press the touch pad on the liftgate
handle to open the liftgate if the RKE
transmitter is within 1 m (3 ft).

Key Access

To access a vehicle with a weak
transmitter battery, see Door Locks
0 18.

KEYS, DOORS, AND WINDOWS 13

Programming Transmitters to
the Vehicle

Only RKE transmitters programmed to
the vehicle will work. If a transmitter
is lost or stolen, a replacement can be
purchased and programmed through
your dealer.

The vehicle can be reprogrammed so
that lost or stolen transmitters no
longer work. Each vehicle can have up
to eight transmitters matched to it.

Programming with Recognized
Transmitters

A new transmitter can be programmed
to the vehicle when there are two
recognized transmitters.

To program, the vehicle must be off
and all of the transmitters, both
currently recognized and new, must
be with you.

1. Place the two recognized
transmitters in the cupholder.

2. Remove the key lock cylinder cap
on the driver door handle. See
Door Locks 0 18. Inser t the
vehicle key of the transmitter
into the key lock cylinder on the

14 KEYS, DOORS, AND WINDOWS

driver door and turn the key
counterclockwise, to the unlock
position, five times within
10 seconds.

The DIC displays READY FOR
REMOTE #2, 3, 4, ETC.

3. Place the new transmitter into
the transmitter pocket. The
transmitter pocket is inside the
center console storage area
between the driver and front
passenger seats. The storage area
will need to be opened and the
storage tray lifted up to access
the transmitter pocket.

4. Press ENGINE START/STOP.
When the transmitter is learned
the DIC display will show that it
is ready to program the next
transmitter.

5. Remove the transmitter from the
transmitter pocket and press the

transmitter

To program additional
transmitters, repeat Steps 3–5.

When all additional transmitters
are programmed, press and hold
ENGINE START/STOP for
12 seconds to exit
programming mode.

6. Return the key back into the
transmitter.

7. Replace the key lock cylinder
cap. See Door Locks 0 18.

Programming without Recognized
Transmitters

If two currently recognized
transmitters are not available, follow
this procedure to program up to eight
transmitters. This feature is not
available in Canada. This procedure
will take approximately 30 minutes to

K or Q button.

complete. The vehicle must be off and
all of the transmitters you wish to
program must be with you.

1. Remove the key lock cylinder cap
on the driver door handle. See
Door Locks 0 18. Inser t the
vehicle key of the transmitter
into the key lock cylinder on the
driver door handle and turn the
key counterclockwise, to the
unlock position, five times within
10 seconds.

The DIC displays REMOTE
LEARN PENDING,
PLEASE WAIT.

2. Wait for 10 minutes until the
DIC displays PRESS ENGINE
START BUTTON TO LEARN and
then press ENGINE
START/STOP.

The DIC display will again show
REMOTE LEARN PENDING,
PLEASE WAIT.

3. Repeat Step 2 two additional
times. After the third time all
previously known transmitters
will no longer work with the

vehicle. Remaining transmitters
can be relearned during the next
steps.

The DIC display should now
show READY FOR REMOTE # 1.

4. Place the new transmitter into
the transmitter pocket. The
transmitter pocket is inside the
center console storage area
between the driver and front
passenger seats. The storage area
will need to be opened and the
storage tray lifted up to access
the transmitter pocket.

5. Press ENGINE START/STOP.
When the transmitter is learned
the DIC display will show that it
is ready to program the next
transmitter.

6. Remove the transmitter from the
transmitter pocket and press the

transmitter

To program additional
transmitters, repeat Steps 4–6.

When all additional transmitters
are programmed, press and hold
ENGINE START/STOP for
12 seconds to exit
programming mode.

7. Return the key back into the
transmitter.

8. Replace the key lock cylinder
cap. See Door Locks 0 18.

Starting the Vehicle with a Low
Transmitter Battery

When the vehicle is started, if the
transmitter battery is weak, the DIC
may display NO REMOTE DETECTED
or NO REMOTE KEY WAS DETECTED
PLACE KEY IN TRANSMITTER

KEYS, DOORS, AND WINDOWS 15

POCKET THEN START YOUR
VEHICLE. The DIC may also display
REPLACE BATTERY IN REMOTE KEY.

To start the vehicle:

1. Open the center console storage
area and the storage tray.

K or Q button.

2. Place the transmitter in the
transmitter pocket.

3. With the vehicle in P (Park) or
N (Neutral), press the brake pedal
and ENGINE START/STOP.

Replace the transmitter battery
as soon as possible.

16 KEYS, DOORS, AND WINDOWS

Battery Replacement

Warning

{

Never allow children to play with
the RKE transmitter. The
transmitter contains a small
battery, which can be a choking
hazard. If swallowed, internal burns
can occur, resulting in severe injury
or death. Seek medical attention
immediately if a battery is
swallowed.

Caution

Caution

Always replace the battery with the
correct type. Replacing the battery
with an incorrect type could
potentially create a risk of battery
explosion. Dispose of used batteries
according to instructions and local
laws. Do not attempt to burn,
crush, or cut the used batter y.

Replace the battery if the DIC displays
REPLACE BATTERY IN REMOTE KEY.

1. Press the button on the side of
the transmitter near the bottom
and pull the key out. Never pull
the key out without pressing the
button.

When replacing the battery, do not
touch any of the circuitry on the
transmitter. Static from your body
could damage the transmitter.

2. Separate the two halves of the
transmitter using a flat tool
inserted into the bottom center
of the transmitter. Do not use
the key slot.

/ : This button is on the RKE

transmitter for remote start.

The climate control system will use
the previous settings during a remote
start. The rear window defogger may
come on during remote start based on
cold ambient conditions. The rear
window defogger indicator light does
not come on during remote start.

If the vehicle has auto heated or
ventilated seats they may come on

3. Remove the old battery. Do not
use a metal object.

4. Insert the new battery on the
back housing, positive side facing
down. Replace with a CR2032 or
equivalent battery.

5. Align the front and back housing
then snap the transmitter
together.

6. Reinsert the key.

Remote Vehicle Start

This feature allows the engine to be
started from outside of the vehicle.

during a remote start. See Heated and
Ventilated Front Seats 0 51.

Laws in some local communities may
restrict the use of remote starters. For
example, some laws may require a
person using remote start to have the
vehicle in view. Check local
regulations for any requirements.

Do not use the remote start feature if
the vehicle is low on fuel. The vehicle
could run out of fuel.

Other conditions can affect the
performance of the transmitter. See

Remote Keyless Entry (RKE) System
0 10.

KEYS, DOORS, AND WINDOWS 17

Starting the Engine Using Remote
Start

1. Press and release
transmitter.

2. Immediately press and hold
for at least four seconds or until
the turn signal lamps flash. The
turn signal lamps f lashing
confirms the request to remote
start the vehicle has been
received.

During the remote start the
doors will be locked and the
parking lamps will remain on as
long as the engine is running.

The engine will shut off after
15 minutes unless a time
extension is done or the ignition
is turned on.

3. With the RKE transmitter in the
vehicle, press the brake pedal
and start the vehicle to drive.

Extending Engine Run Time

The engine run time can also be
extended by another 15 minutes,
if during the first 15 minutes

Q on the RKE

/

18 KEYS, DOORS, AND WINDOWS

Steps 1 and 2 are repeated while the
engine is still running. An extension
can be requested 30 seconds after
starting. This provides a total of
30 minutes.

The remote start can only be
extended once.

When the remote start is extended,
the second 15-minute period is added
on to the first 15 minutes for a total
of 30 minutes.

A maximum of two remote starts, or a
remote start with an extension, are
allowed between ignition cycles.

The ignition must be turned on and
then off before the remote start
procedure can be used again.

Canceling a Remote Start

To cancel a remote start, do any of
the following:

.

Press and hold
parking lamps turn off.

.

Turn on the hazard warning
flashers.

.

Turn the vehicle on and then off.

/ until the

Conditions in Which Remote Start
Will Not Work

The remote start will not operate if
any of the following occur:

.

The RKE transmitter is in the
vehicle.

.

The ignition is on.

.

The hood is not closed.

.

The hazard warning flashers
are on.

.

There is an emission control
system malfunction.

.

The engine coolant temperature is
too high.

.

The oil pressure is low.

.

Two remote vehicle starts or a
start with an extension have
already been used.

.

The vehicle is not in P (Park).

Door Locks

Warning

{

Unlocked doors can be dangerous.

.

Passengers, especially
children, can easily open the
doors and fall out of a moving
vehicle. The doors can be
unlocked and opened while
the vehicle is moving. The
chance of being thrown out of
the vehicle in a crash is
increased if the doors are not
locked. So, all passengers
should wear seat belts
properly and the doors should
be locked whenever the
vehicle is driven.

.

Young children who get into
unlocked vehicles may be
unable to get out. A child can
be overcome by extreme heat
and can suffer permanent
injuries or even death from
heat stroke. Always lock the
vehicle whenever leaving it.

(Continued)

Warning (Continued)

.

Outsiders can easily enter
through an unlocked door
when you slow down or stop
the vehicle. Locking the doors
can help prevent this from
happening.

To lock/unlock the doors from outside
the vehicle:

.

Press

Q or K on the Remote

Keyless Entry (RKE) transmitter.
See Remote Keyless Entry (RKE)
System Operation 0 10.

.

Use the key in the key lock
cylinder in the driver door. The
key lock cylinder is covered with
a cap.

To lock/unlock the doors from inside
the vehicle:

.

Press

Q or K on the power door

lock switch. See Power Door Locks
0 21.

.

Pull once on the door handle to
unlock the door and again to open
the door.

.

On the rear doors, push down on
the door lock knob to lock the
door manually.

Keyless Access

If equipped, the RKE transmitter must
be within 1 m (3 ft) of the liftgate or
door being opened.

KEYS, DOORS, AND WINDOWS 19

To lock or unlock the vehicle from the
driver door:

.

Press the button on the driver
door handle once to unlock the
driver door only.

.

Press the button again within
five seconds to unlock all doors.

.

Press the button a third time to
lock all doors.

When leaving the vehicle, press the
button on any door handle to lock all
doors.

To lock or unlock the vehicle from any
passenger door:

.

Press the button on the passenger
door handle. This will lock or
unlock all doors.

See Remote Keyless Entry (RKE) System
Operation 0 10.

20 KEYS, DOORS, AND WINDOWS

Driver Door Key Lock Cylinder
Access (In Case of Dead Battery)

To access the driver door key lock
cylinder:

1. Pull the door handle (1) to the
open position and hold it open
until the cap removal is
complete.

2. Insert the key into the slot (3) on
the bottom of the cap (2) and lift
the key upward.

3. Move the cap (2) rearward and
remove.

4. Use the key in the cylinder.

To replace the cap:

1. Pull the door handle (1) to the
open position and hold it open
until the cap installation is
complete.

2. Insert the two tabs (6) at the
back of the cap between the
seal (5) and the metal base (4).

3. Slide the cap forward and press
the forward edge to install the
cap in place.

4. Release the door handle.

5. Check that the cap is secure.

Free-Turning Locks

The door key lock cylinder turns freely
when either the wrong key is used,
or the correct key is not fully inserted.
The free-turning door lock feature
prevents the lock from being forced
open. To reset the lock, turn it to the
vertical position with the correct key
fully inserted. Remove the key and
insert it again. If this does not reset
the lock, turn the key halfway around
in the cylinder and repeat the reset
procedure.

Power Door Locks

Q : Press to lock the doors.

If equipped, the fuel door is also
locked or unlocked using these
features.

K : Press to unlock the doors.

Delayed Locking

This feature delays the locking of the
doors until five seconds after all doors
are closed.

Delayed locking can only be turned on
when Open Door Anti Lockout has
been turned off.

KEYS, DOORS, AND WINDOWS 21

When

Q is pressed on the power door

lock switch while the door is open, a
chime will sound three times
indicating delayed locking is active.

The doors will lock automatically
five seconds after all doors are closed.
If a door is reopened before that time,
the five-second timer will reset when
all doors are closed again.

Q on the door lock switch again

Press
or press

lock the doors immediately.

This feature can also be programmed.
See Vehicle Personalization 0 134.

Q on the RKE transmitter to

Automatic Door Locks

The doors will lock automatically
when all doors are closed, the ignition
is on, and the vehicle is shifted out of
P (Park).

If a vehicle door is unlocked and then
opened and closed, the doors will lock
either when your foot is removed from
the brake or the vehicle speed
becomes faster than 13 km/h (8 mph).

22 KEYS, DOORS, AND WINDOWS

To unlock the doors:

.

Press

K on the power door lock

switch.

.

Shift the transmission into
P (Park).

Automatic door locking cannot be
disabled. Automatic door unlocking
can be programmed. See Vehicle
Personalization 0 134.

Lockout Protection

If the ignition is on or in ACC/
ACCESSORY and the power door lock
switch is pressed with the driver door
open, all the doors will lock and only
the driver door will unlock.

If the vehicle is off and locking is
requested while a door is open, when
all doors are closed the vehicle will
check for RKE transmitters inside.
If an RKE transmitter is detected and
the number of RKE transmitters inside
has not reduced, the driver door will
unlock and the horn will chirp three
times.

Lockout Protection can be manually
overridden with the driver door open

by pressing and holding
power door lock switch.

Open Door Anti-Lockout

If Open Door Anti Lockout is turned
on and the vehicle is off, the driver
door is open, and locking is requested,
all the doors will lock and the driver
door will remain unlocked. The Open
Door Anti Lockout feature can be
turned on or off. See Vehicle
Personalization 0 134.

Q on the

Safety Locks

The rear door safety locks prevent
passengers from opening the rear
doors from inside the vehicle.

Manual Safety Locks

If equipped, the safety lock is on the
inside edge of the rear doors. To use
the safety lock:

1. Move the lever down to the lock
position.

2. Close the door.

3. Do the same for the other
rear door.

To open a rear door when the safety
lock is on:

1. Unlock the door by activating the
inside handle, by pressing the
power door lock switch, or by
using the Remote Keyless
Entry (RKE) transmitter.

2. Open the door from the outside.

When the safety lock is enabled,
adults and older children will not be
able to open the rear door from the
inside. Cancel the safety locks to
enable the doors to open from the
inside.

To cancel the safety lock:

1. Unlock the door and open it
from the outside.

2. Move the lever up to unlock. Do
the same for the other door.

Doors

Liftgate

Warning

{

Exhaust gases can enter the vehicle
if it is driven with the liftgate or
trunk/hatch open, or with any
objects that pass through the seal
between the body and the trunk/
hatch or liftgate. Engine exhaust
contains carbon monoxide (CO)
which cannot be seen or smelled.
It can cause unconsciousness and
even death.

If the vehicle must be driven with
the liftgate or trunk/hatch open:

.

Close all of the windows.

.

Fully open the air outlets on
or under the instrument
panel.

(Continued)

KEYS, DOORS, AND WINDOWS 23

Warning (Continued)

.

Adjust the climate control
system to a setting that
brings in only outside air and
set the fan speed to the
highest setting. See “Climate
Control Systems” in the Index.

.

If the vehicle is equipped with
a power liftgate, disable the
power liftgate function.

See Engine Exhaust 0 185.

Caution

To avoid damage to the liftgate or
liftgate glass, make sure the area
above and behind the liftgate is
clear before opening it.

24 KEYS, DOORS, AND WINDOWS

Power Liftgate Operation

Warning

{

You or others could be injured if
caught in the path of the power
liftgate. Make sure there is no one
in the way of the liftgate as it is
opening and closing.

Caution

Driving with an open and
unsecured liftgate may result in
damage to the power liftgate
components.

The power liftgate switch is on the
driver door. The vehicle must be in
P (Park).

The modes are:

MAX : Opens to maximum height.

3/4 : Opens to a reduced height that

can be set from 3/4 to fully open. Use
to prevent the liftgate from opening
into overhead obstructions such as a
garage door or roof-mounted cargo.
The liftgate can be manually opened
all the way.

OFF : Opens manually only.

To power open or close the liftgate,
select MAX or 3/4 mode.

.

.

.

b twice quickly on the RKE

Press
transmitter until the liftgate
moves.

Press

8 on the driver door. The

driver door must either be
unlocked or locked without the
security armed.

Press the touch pad on the
underside of the liftgate handle
after unlocking all doors. A locked
vehicle can be opened if the RKE
transmitter is within 1 m (3 ft) of
the touch pad.

.

Press

l on the bottom of the

liftgate next to the pull cup to
close.

Press any liftgate button, the touch
pad, or

b on the RKE transmitter

while the liftgate is moving to stop it.
Pressing any liftgate button

or pressing
RKE transmitter again restarts the
operation in the reverse direction.
Pressing the touch pad on the liftgate
handle will restart the motion, but
only in the opening direction.

b twice quickly on the

Caution

Manually forcing the liftgate to
open or close during a power cycle
can damage the vehicle. Allow the
power cycle to complete.

The power liftgate may be temporarily
disabled under extreme low
temperatures, or after repeated power
cycling over a short period of time.
If this occurs, the liftgate can still be
operated manually.

If the vehicle is shifted out of P (Park)
while the power function is in
progress, the liftgate will continue to
completion. If the vehicle is
accelerated before the liftgate has
completed moving, the liftgate may
stop or reverse direction. Check for
Driver Information Center (DIC)
messages and make sure the liftgate is
closed and latched before driving.

Falling Liftgate Detection

If the power liftgate automatically
closes after a power opening cycle, it
indicates that the system is reacting
to excess weight on the liftgate or a
possible support strut failure.
A repetitive chime will sound while
the falling liftgate detection feature is
operating. Remove any excess weight.
If the liftgate continues to
automatically close after opening, see
your dealer for service before using
the power liftgate.

Interfering with the power liftgate
motion or manually closing the
liftgate too quickly after power
opening may resemble a support strut
failure. This could also activate the
falling liftgate detection feature. Allow

KEYS, DOORS, AND WINDOWS 25

the liftgate to complete its operation
and wait a few seconds before
manually closing the liftgate.

Obstacle Detection Features

If the liftgate encounters an obstacle
during a power open or close cycle,
the liftgate will automatically reverse
direction and move a short distance
away from the obstacle. After
removing the obstruction, the power
liftgate operation can be used again.
If the liftgate encounters multiple
obstacles on the same power cycle,
the power function will deactivate.
After removing the obstructions,
manually close the liftgate. This will
allow normal power operation
functions to resume.

If the vehicle is locked while the
liftgate is closing, and an obstacle is
encountered that prevents the liftgate
from completely closing, the horn will
sound as an alert that the liftgate did
not close.

Pinch sensors are on the side edges of
the liftgate. If an object is caught
between the liftgate and the vehicle
and presses against a sensor, the

26 KEYS, DOORS, AND WINDOWS

liftgate will reverse direction and open
fully. The liftgate will remain open
until it is activated again or closed
manually.

Setting the 3/4 Mode

To change the position the liftgate
stops at when opening:

1. Select MAX or 3/4 mode and
power open the liftgate.

2. Stop the liftgate movement at
the desired height by pressing
any liftgate button. Manually
adjust the liftgate position if
needed.

3. Press and hold
pull cup on the outside of the
liftgate until the turn signals
flash and a beep sounds. This
indicates the setting has been
recorded.

The liftgate cannot be set below a
minimum programmable height.
If there is no light flash or sound,
then the height adjustment may be
too low.

l next to the

Manual Operation

Select OFF to manually operate the
liftgate.

Caution

Attempting to move the liftgate too
quickly and with excessive force
may result in damage to the
vehicle.

Operate the liftgate manually with a
smooth motion and moderate speed.
The system includes a feature which
limits the manual closing speed to
protect the components.

To unlock the liftgate, press
power door lock switch or press

the Remote Keyless Entry (RKE)
transmitter twice within five seconds.
See Remote Keyless Entry (RKE) System
Operation 0 10.

K on the

K on

To open the liftgate, press the touch
pad under the liftgate handle and
lift up.

Use the pull cup to lower and close
the liftgate. Do not press the touch
pad while closing the liftgate. This
may cause the liftgate to be
unlatched.

If equipped with Keyless Access, the
liftgate can be opened when locked if
the RKE transmitter is within 1 m
(3 ft) of the touch pad. See Remote

Keyless Entry (RKE) System Operation
0 10.

The liftgate has an electric latch.
If the battery is disconnected or has
low voltage, the liftgate will not open.
The liftgate will resume operation
when the battery is reconnected and
charged.

Always close the liftgate before
driving.

Hands-Free Operation

If equipped, the liftgate may be
operated with a kicking motion under
the left side of the rear bumper.

The RKE transmitter must be within
1 m (3 ft) of the rear bumper to
operate the power liftgate hands-free.

The hands-free feature will not work
while the liftgate is moving. To stop
the liftgate while in motion use one of
the liftgate switches.

The hands-free feature can be
customized. See Vehicle Personalization
0 134. Choose from the following:

On-Open and Close : The kicking
motion is activated to both open and
close the liftgate.

On-Open Only : The kicking motion is
activated to only open the liftgate.

Off : The feature is disabled.

Kick Zone

To operate, move your foot in a
forward kicking motion under the left
side of the rear bumper, at the
location of the projected logo, then
pull it back. Then step back. The kick
must come within 14 cm (6 in) of the
rear bumper to activate.

KEYS, DOORS, AND WINDOWS 27

Caution

Splashing water may cause the
liftgate to open. Keep the RKE
transmitter away from the rear
bumper detection area or turn the
liftgate mode to OFF when cleaning
or working near the rear bumper to
avoid accidental opening.

.

Do not sweep your foot side
to side.

.

Do not keep your foot under the
bumper; the liftgate will not
activate.

.

Do not touch the liftgate until it
has stopped moving.

.

This feature may be temporarily
disabled under some conditions.
If the liftgate does not respond to
the kick, open or close the liftgate
by another method or start the
vehicle. The feature will be
re-enabled.

28 KEYS, DOORS, AND WINDOWS

When closing the liftgate using this
feature, there will be a short delay.
The taillamps will f lash and a chime
will sound. Step away from the liftgate
before it starts moving.

Projected Logo

If equipped with this feature, a vehicle
logo will be projected for one minute
onto the ground near the rear bumper
when an RKE transmitter is detected
within approximately 2 m (6 ft). The
projected logo may not be visible
under brighter daytime conditions.

The projected logo shows where the
kicking motion is to take place.

The projected logo will only be
available for this RKE transmitter after
it has been out of range for at least
20 seconds.

If an RKE transmitter is again
detected within approximately 2 m
(6 ft) of the liftgate, or another
hands-free operation has been
detected, the one-minute timer will be
reset.

The projected logo will not work
under these conditions:

.

.

.

2. 2 m (6 ft) Projected Logo
Detection Zone

The vehicle battery is low.

The transmission is not in
P (Park).

Hands Free Liftgate Control is set
to Off in vehicle personalization.
See Vehicle Personalization 0 134.

.

The power liftgate is turned off.

.

The vehicle remains parked for
72 hours or more, with no RKE
transmitter use or Keyless Access
operation. To re-enable, press any
button on the RKE transmitter or
open and close a vehicle door.

The projected logo will not work for a
single RKE transmitter when a
transmitter:

.

Has been left within
approximately 5 m (15 ft) of the
liftgate for several minutes.

.

Has been left inside the vehicle
and all vehicle doors are closed.

.

Has approached the area outside
of the liftgate five times within
10 minutes.

1. 1 m (3 ft) Hands-Free
Operation Detection Zone

Lens Cleaning

Use a soft, damp cloth to clean the
recessed lens.

KEYS, DOORS, AND WINDOWS 29

30 KEYS, DOORS, AND WINDOWS

Hands-Free Liftgate and Projected Logo Availability

Action Hands-Free Liftgate Projected Logo

RKE transmitter entering projected logo
detection zone

RKE transmitter left inside projected
logo detection zone for minimum of
10 minutes

RKE transmitter brought in and out of
projected logo detection zone five times
or more within 10 minutes

Vehicle remains parked for more than
72 hours

Vehicle battery is low Non-operative Off

Transmission is not in P (Park) Non-operative Off

Power liftgate is turned off Non-operative Off

Hands-free liftgate is disabled in
vehicle personalization

Operative On for one minute

Operative Off until RKE transmitter button press

or a door is opened and closed

Operative Off for one hour or until RKE

transmitter button press or a door is
opened and closed

Operative Off until RKE transmitter button press

or a door is opened and closed

Non-operative Off

Vehicle Security

This vehicle has theft-deterrent
features; however, they do not make
the vehicle impossible to steal.

Fast Flash : Vehicle is unsecured.
A door, the hood, or the liftgate
is open.

Slow Flash : Alarm system is armed.

Arming the Alarm System

Vehicle Alarm System

This vehicle has an anti-theft alarm
system.

The indicator light, on the instrument
panel near the windshield, indicates
the status of the system.

Off : Alarm system is disarmed.

On Solid : Vehicle is secured during

the delay to arm the system.

1. Close the liftgate and the hood.
Turn off the vehicle.

2. Lock the vehicle in one of
three ways:

.

Use the RKE transmitter.

.

Use the Keyless Access
system.

.

With a door open, press the
inside

3. After 30 seconds the alarm
system will arm, and the
indicator light will begin to
slowly flash indicating the alarm

system is operating. Pressing
on the RKE transmitter a second
time will bypass the 30-second
delay and immediately arm the
alarm system.

The vehicle alarm system will not arm
if the doors are locked with the key.

Q.

KEYS, DOORS, AND WINDOWS 31

If the driver door is opened without
first unlocking with the RKE
transmitter, the horn will chirp and
the lights will f lash to indicate
pre-alarm. If the vehicle is not started,
or the door is not unlocked by

pressing
during the 10-second pre-alarm, the
alarm will be activated.

The alarm will also be activated if a
passenger door, the liftgate, or the
hood is opened without first
disarming the system. When the
alarm is activated, the turn signals
flash and the horn sounds for about
30 seconds. The alarm system will
then re-arm to monitor for the next
unauthorized event.

Disarming the Alarm System

To disarm the alarm system or turn

Q

off the alarm if it has been activated:

.

.

.

K on the RKE transmitter

Press

K on the RKE transmitter.

Unlock the vehicle using the
Keyless Access system.

Start the vehicle.

32 KEYS, DOORS, AND WINDOWS

To avoid setting off the alarm by
accident:

.

Lock the vehicle after all
occupants have left the vehicle
and all doors are closed.

.

Always unlock a door with the
RKE transmitter or use the Keyless
Access system.

Unlocking the driver door with the key
will not disarm the system or turn off
the alarm.

How to Detect a Tamper
Condition

If K is pressed and the horn chirps
and the lights f lash three times, the
alarm was activated while the alarm
system was armed.

If the alarm system has been
activated, a message will appear on
the DIC.

Power Sounder, Inclination
Sensor, and Intrusion Sensor

In addition to the standard
theft-deterrent system features, this
system may also have an inclination
sensor, an intrusion sensor, and power
sounder.

The power sounder provides an
audible alarm that is different from
the vehicle’s horn. It has its own
power source, and can sound an alarm
when the vehicle’s battery is
compromised.

The inclination sensor can set off the
alarm if it senses movement of the
vehicle, such as a change in vehicle
orientation.

The intrusion sensor monitors the
vehicle interior, and can set off the
alarm if it senses an unauthorized
entry into the vehicle’s interior. Do
not allow passengers or pets to remain
in the vehicle when the intrusion
sensor is activated.

Before arming the theft-deterrent
system and activating the intrusion
sensor:

.

Make sure all doors and windows
are completely closed.

.

Secure any loose items such as a
sunshades.

.

Make sure there are no
obstructions blocking the sensors
in the front overhead console.

Inclination and Intrusion
Sensors Disable Switch

It is recommended that the inclination
and intrusion sensors be deactivated if
pets are left in the vehicle or if the
vehicle is being transported.

With the vehicle turned off, press
in the overhead console. The indicator
light will come on momentarily,
indicating that the sensor has been
disabled until the next time the alarm
system is armed.

o

Steering Column Lock

If equipped, the steering column lock
is a theft-deterrent device. This
feature locks the steering column
when the vehicle is turned off and the
driver door is opened, or when the
driver door is opened and then the

vehicle is turned off. The steering
column unlocks when the vehicle is
turned on.

The Driver Information Center (DIC)
may display one of these messages:

.

A message to service the steering
column lock indicates that an
issue has been detected with the
column lock feature and the
vehicle should be serviced.

.

A message that the steering
column is locked indicates that
the engine is running, but the
steering column is still locked. It is
normal for the column to be
locked during a remote start, but
the column should unlock after
the brake pedal is pressed and the
vehicle is started. No message will
display during a remote start.

.

A message that the steering wheel
must be turned and the vehicle
must be started again indicates
that the column lock mechanism
is bound, the column locking
device was unable to unlock the
steering column, and the vehicle
did not start. If this happens,

immediately turn the steering
wheel from side to side to unbind
the column lock. If this does not
unlock the steering column, turn
the vehicle off and open the driver
door to reset the system. Then
turn the vehicle on and
immediately turn the steering
wheel side to side for about
15 seconds. In some cases, it may
take significant force to unbind
the column.

To keep the steering column from
binding, straighten the front wheels
before turning off the vehicle.

Immobilizer

See Radio Frequency Statement 0 363.

Immobilizer Operation

This vehicle has a passive
theft-deterrent system.

The system does not have to be
manually armed or disarmed.

The vehicle is automatically
immobilized when the vehicle is
turned off.

KEYS, DOORS, AND WINDOWS 33

The immobilization system is
disarmed when the ignition is on or in
ACC/ACCESSORY and a valid
transmitter is present in the vehicle.

The security light, in the instrument
cluster, comes on if there is a problem
with arming or disarming the
theft-deterrent system.

The system has one or more RKE
transmitters matched to an
immobilizer control unit in your
vehicle. Only a correctly matched RKE
transmitter will start the vehicle.
If the transmitter is ever damaged,
you may not be able to start your
vehicle.

When trying to start the vehicle, the
security light may come on briefly
when the ignition is turned on.

34 KEYS, DOORS, AND WINDOWS

If the engine does not start and the
security light stays on, there is a
problem with the system. Turn the
ignition off and try again.

If the vehicle will not change ignition
modes (ACC/ACCESSORY, on, off), and
the RKE transmitter appears to be
undamaged, try another transmitter.
Or, you may try placing the
transmitter in the transmitter pocket
located in the center console. See

Remote Keyless Entry (RKE) System
Operation 0 10.

If the ignition mode will not change
with the other transmitter or in the
transmitter pocket, your vehicle needs
service. If the ignition does change
modes, the first transmitter may be
faulty. See your dealer who can service
the theft-deterrent system and have a
new RKE transmitter programmed to
the vehicle.

It is possible for the immobilizer
system to learn new or replacement
RKE transmitters. Up to eight
transmitters can be programmed for
the vehicle. To program additional
transmitters, see “Programming
Transmitters to the Vehicle” under

Remote Keyless Entry (RKE) System
Operation 0 10.

Do not leave the key or device that
disarms or deactivates the
theft-deterrent system in the vehicle.

Exterior Mirrors

Convex Mirrors

Warning

{

A convex mirror can make things,
like other vehicles, look farther
away than they really are. If you cut
too sharply into the right lane, you
could hit a vehicle on the right.
Check the inside mirror or glance
over your shoulder before changing
lanes.

The passenger side mirror is convex
shaped. A convex mirror’s surface is
curved so more can be seen from the
driver seat.

Power Mirrors

To adjust a mirror:

1. Press

2. Press the arrows on the control

3. Adjust each outside mirror so

4. Press

} or | to select the

driver or passenger side mirror.
The indicator light will
illuminate.

pad to move the mirror in the
desired direction.

that a little of the vehicle and
the area behind it can be seen.

} or | again to deselect

the mirror.

Memory Mirrors

The vehicle may have memory
mirrors. See Memory Seats 0 48.

Side Blind Zone Alert (SBZA)

The vehicle may have SBZA. See Side
Blind Zone Alert (SBZA) 0 229.

Lane Change Alert (LCA)

The vehicle may have LCA. See Lane
Change Alert (LCA) 0 229.

Turn Signal Indicator

The vehicle may have a turn signal
indicator lamp built into the mirror
housing. The turn signal lamp flashes
when the turn signals or hazard
flashers are used.

Puddle Light

The vehicle may have a puddle light
on the mirror housings. The light will
illuminate the ground when the door
is opened.

KEYS, DOORS, AND WINDOWS 35

Folding Mirrors

Manual Folding Mirrors

If equipped, manually fold the mirrors
inward toward the vehicle to prevent
damage when going through an
automatic car wash. Push the mirror
outward to return it to the original
position.

Power Folding Mirrors

If equipped, press { to power fold
the mirrors. Press

{ again to unfold.

36 KEYS, DOORS, AND WINDOWS

Resetting the Power Folding
Mirrors

Reset the power folding mirrors if:

.

The mirrors are accidentally
obstructed while folding.

.

They are accidentally manually
folded/unfolded.

.

The mirrors do not stay in the
unfolded position.

.

The mirrors vibrate at normal
driving speeds.

Fold and unfold the mirrors one time
using the mirror controls to reset
them to their normal position. A noise
may be heard during the resetting of
the power folding mirrors. This sound
is normal after a manual folding
operation.

Remote Folding Mirror

If equipped, press and hold Q on the
RKE transmitter for approximately
one second to automatically fold the

exterior mirrors. Press and hold
the RKE transmitter for approximately

K on

one second to unfold. See Remote
Keyless Entry (RKE) System Operation

0 10.

This feature is turned on or off
through vehicle personalization. See
Vehicle Personalization 0 134.

Heated Mirrors

K

See “Rear Window Defogger” under

Dual Automatic Climate Control System
0 151.

Automatic Dimming Mirror

If the vehicle has the automatic
dimming mirror, the driver outside
mirror automatically adjusts for the
glare of headlamps behind you.

: Press to heat the mirrors.

Reverse Tilt Mirrors

If equipped with memory seats, the
passenger and/or driver mirror tilts to
a preselected position when the
vehicle is in R (Reverse). This allows
the curb to be seen when parallel
parking.

The mirror(s) return to the original
position when:

.

The vehicle is shifted out of
R (Reverse), or remains in
R (Reverse) for about 30 seconds.

.

The ignition is turned off.

.

The vehicle is driven in
R (Reverse) above a set speed.

To turn this feature on or off, see
Vehicle Personalization 0 134.

Interior Mirrors

Interior Rearview Mirrors

Adjust the rearview mirror for a clear
view of the area behind the vehicle.

Do not spray glass cleaner directly on
the mirror. Use a soft towel dampened
with water.

Manual Rearview Mirror

Push the tab forward for daytime use
and pull it rearward for nighttime use
to avoid glare of the headlamps from
behind.

Automatic Dimming
Rearview Mirror

If equipped, automatic dimming
reduces the glare of headlamps from
behind. The dimming feature comes
on when the vehicle is started.

Rear Camera Mirror

If equipped, this automatic dimming
mirror provides a wide angle camera
view of the area behind the vehicle.

Pull the tab to turn on the display.
Push the tab to turn it off. When off
the mirror is automatic dimming.
Adjust the mirror for a clear view of
the area behind the vehicle while the
display is off.

KEYS, DOORS, AND WINDOWS 37

Press V to scroll through the
adjustment options.

Press

t and u to adjust the settings

using the indicators on the mirror.
The indicators will remain visible for
five seconds after the last button
activation, and the settings will
remain saved.

38 KEYS, DOORS, AND WINDOWS

The adjustment options are:

.

.

Brightness

Tilt

Warning

{

The Rear Camera Mirror (RCM) has
a limited view. Portions of the road,
vehicles, and other objects may not
be seen. Do not drive or park the
vehicle using only this camera.
Objects may appear closer than
they are. Check the outside mirrors
or glance over your shoulder when
making lane changes or merging.
Failure to use proper care may
result in injury, death, or vehicle
damage.

.

Zoom

Troubleshooting

See your dealer for service if a blue
screen and

mirror, and the display shuts off. Also,
push the tab as indicated to return to
the automatic dimming mode.

The Rear Camera Mirror may not work
properly or display a clear image if:

.

.

3 are displayed in the

There is glare from the sun or
headlamps. This may obstruct
objects from view. If needed, push
the tab to turn off the display.

Dirt, snow, or other debris blocks
the camera lens. Clean the lens
with a soft damp cloth, or if

equipped, with the Rear Camera
Washer. See Rear Window Wiper/
Washer 0 106.

.

The camera’s mounting on the
vehicle has been damaged, and/or
the position or the mounting angle
of the camera has changed.

KEYS, DOORS, AND WINDOWS 39

Windows

Warning

{

Never leave a child, a helpless adult,
or a pet alone in a vehicle,
especially with the windows closed
in warm or hot weather. They can
be overcome by the extreme heat
and suffer permanent injuries or
even death from heat stroke.

The vehicle aerodynamics are
designed to improve fuel economy
performance. This may result in a

40 KEYS, DOORS, AND WINDOWS

pulsing sound when either rear
window is down and the front
windows are up. To reduce the sound,
open either a front window or the
sunroof, if equipped.

Power Windows

Warning

{

Children could be seriously injured
or killed if caught in the path of a
closing window. Never leave the
Remote Keyless Entry (RKE)
transmitter in a vehicle with
children. When there are children in
the rear seat, use the window
lockout switch to prevent operation
of the windows. See Keys 0 9.

The power windows work when the
ignition is on, in ACC/ACCESSORY,
or when Retained Accessor y Power
(RAP) is active. See Retained Accessory
Power (RAP) 0 182.

Using the window switch, press to
open or pull to close the window.

The windows may be temporarily
disabled if they are used repeatedly
within a short time.

Window Lockout

This feature stops the rear passenger
window switches from working.

.

Press

2 to engage the rear

window lockout feature. The
indicator light is on when engaged.

.

2 again to disengage.

Press

Window Express Movement

All windows can be opened without
holding the window switch. Press the
switch down fully and quickly release
to express open the window.

If equipped, pull the window switch
up fully and quickly release to express
close the window.

Briefly press or pull the window
switch in the same direction to stop
that window’s express movement.

Window Automatic Reversal
System

The express-close feature will reverse
window movement if it comes in
contact with an object. Extreme cold
or ice could cause the window to
auto-reverse. The window will operate
normally after the object or condition
is removed.

Automatic Reversal System
Override

Warning

{

If automatic reversal system
override is active, the window will
not reverse automatically. You or
others could be injured and the
window could be damaged. Before
using automatic reversal system

(Continued)

Warning (Continued)

override, make sure that all people
and obstructions are clear of the
window path.

When the engine is on, override the
automatic reversal system by pulling
and holding the window switch if
conditions prevent it from closing.

Programming the Power
Windows

Programming may be necessary if the
vehicle battery has been disconnected
or discharged. If the window is unable
to express-up, program each
express-close window:

1. Close all doors.

2. Turn the ignition on or to ACC/
ACCESSORY.

3. Partially open the window to be
programmed. Then close it and
continue to pull the switch
briefly after the window has fully
closed.

KEYS, DOORS, AND WINDOWS 41

4. Open the window and continue
to press the switch briefly after
the window has fully opened.

Remote Window Operation

If equipped, this feature allows all
windows to be opened remotely.
If enabled in vehicle personalization,

press and hold
transmitter. See Vehicle Personalization
0 134.

K on the RKE

Sun Visors

Pull the sun visor down to block glare.
Detach the sun visor from the center
mount to pivot to the side window
and, if equipped, extend along the rod.

42 KEYS, DOORS, AND WINDOWS

Roof

Sunroof

If equipped, the ignition must be on
or in ACC/ACCESSORY, or Retained
Accessory Power (RAP) must be active
to operate the sunroof. See Ignition

Positions 0 176 and
Retained Accessory Power (RAP) 0 182.

1. Sunroof Switch

2. Sunshade Switch

Sunroof Express Operation : Press
and release
release again to move to the partially

e (1) to vent. Press and

opened comfort stop position. Press
and release again to express-open to
the fully opened position. Press and

e (1) at any time to stop

release

movement. Press and release
to express-close. Press and release

g (1) at any time to stop

movement.

Sunroof Manual Operation : The
sunroof can change to manual mode

by holding

sunroof will now open as long as
(1) is held. Press and release e (1)

again to change back to express
operation.

Power Sunshade Express
Operation : Press and release

to express-open the sunshade. Press

and release

movement. Press and release
to express-close the sunshade. Press

and release
stop movement.

e (1) while opening. The

C (2) at any time to stop

Q (2) at any time to

g (1)

e

C (2)

Q (2)

Power Sunshade Manual
Operation : The sunshade can change

to manual mode by holding
while opening. The sunroof will now

open as long as

and release
back to express operation.

The sunroof cannot be opened or
closed if the vehicle has an electrical
failure.

C (2) is held. Press

C (2) again to change

C (2)

Automatic Reversal System

The sunroof and power sunshade have
an automatic reversal system that is
only active when the sunroof and
power sunshade, if equipped, are
operated in express-close mode.

If an object is in the path while
express-closing, the reversal system
will detect an object, stop, and open
the sunroof or power sunshade again.

If frost or other conditions prevent
closing, override the feature by closing
the sunroof or power sunshade in
manual mode. To stop movement,
release the switch.

Dirt and debris may collect on the
sunroof seal or in the track. This
could cause an issue with sunroof
operation or noise. It could also plug
the water drainage system.
Periodically open the sunroof and
remove any obstacles or loose debris.
Wipe the sunroof seal and roof sealing
area using a clean cloth, mild soap,
and water. Do not remove grease from
the sunroof.

If water is seen dripping into the
water drainage system, this is normal.

KEYS, DOORS, AND WINDOWS 43

44 SEATS AND RESTRAINTS

Seats and Restraints

Head Restraints

Head Restraints . . . . . . . . . . . . . . . . . . . . 45

Front Seats

Seat Adjustment . . . . . . . . . . . . . . . . .. . 46
Lumbar Adjustment . . . . . . . . . . . . . . . 47
Reclining Seatbacks . . . . . . . . . . . . . . . 47
Memory Seats . . . . . . . . . . . . . . . . . . . . . . 48
Heated and Ventilated Front

Seats . . . . . . . . . . . . . . . .. . . . . . . . . . .. . . 51

Rear Seats

Rear Seats . . . . . . . . . . . . . . . . . . . .. . . . . . 52
Rear Seat Armrest . . . . . . . . . . . . . . . . . 55
Heated Rear Seats . . . . . .. . . . . . . . . . . 55

Seat Belts

Seat Belts . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
How to Wear Seat Belts

Properly . . . . . . . . . . . . . . . . . . . .. . . . . . . 57
Lap-Shoulder Belt . . . . . . . . . . . . . . . . . . 59
Seat Belt Use During

Pregnancy . . . . . . . . . . . . . . . . . . . . . . . . . 62
Seat Belt Extender . . . . . . . . . . . . . . . . . 62
Safety System Check . . . . . . . . . . . . . . 62
Seat Belt Care . . . . . . . . . . . . .. . . . . . . .. 63
Replacing Seat Belt System Parts

after a Crash . . . . . . . . . . . . . . . . . . . . . . 63

Airbag System

Airbag System . . . . . . . . . . . . . . . . . . . . . 64
Where Are the Airbags? . . . . . . . . . . . 66
When Should an Airbag

Inflate? . . . . . . . . .. . . . . . . . . . . . . . . . . . 67
What Makes an Airbag Inflate? . . . 68
How Does an Airbag Restrain? . . . 68
What Will You See after an Airbag

Inflates? . . . . . . . . . .. . . . . . . . . . . . .. . . 68
Passenger Sensing System . . . . . . . . 70
Servicing the Airbag-Equipped

Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Adding Equipment to the

Airbag-Equipped Vehicle . . . . . . . . 74
Airbag System Check . . . . . . .. . . . . . . 75
Replacing Airbag System Parts

after a Crash . . . . . . . . . . . . . . . . . . . . . . 75

Child Restraints

Older Children . . . . . . . .. . . . . . .. . . . . . 76
Infants and Young Children . . . . . . 77
Child Restraint Systems . . . . . . . . . . . 80
Where to Put the Restraint . . . . . . . 81
Lower Anchors and Tethers for

Children (LATCH System) . . . . . . . 83
Replacing LATCH System Parts

After a Crash . . . . . . . . . . . . .. . . . . . . . 89
Securing Child Restraints (With

the Seat Belt in the

Rear Seat) . . . . . . . . . . . . . . . . . .. . . . . . 89

Securing Child Restraints (With

the Seat Belt in the
Front Seat) . . . . . . . . . . . . . . . . . . . . . . . 91

Head Restraints

The vehicle’s front seats have
adjustable head restraints in the
outboard seating positions.

Warning

{

With head restraints that are not
installed and adjusted properly,
there is a greater chance that
occupants will suffer a neck/spinal
injury in a crash. Do not drive until
the head restraints for all occupants
are installed and adjusted properly.

If your vehicle has rear head
restraints that fold down, always
return them to the full upright
position whenever an occupant is
seated in the seat.

Adjust the head restraint so that the
top of the restraint is at the same
height as the top of the occupant’s
head. This position reduces the
chance of a neck injury in a crash.

Front Seats

The vehicle’s front seats have
adjustable head restraints in the
outboard seating positions.

SEATS AND RESTRAINTS 45

The height of the head restraint can
be adjusted.

To raise or lower the head restraint,
press the button located on the side of
the head restraint and pull up or push
the head restraint down, and release
the button. Pull and push on the head
restraint after the button is released
to make sure that it is locked in place.

The front seat outboard head
restraints are not removable.

46 SEATS AND RESTRAINTS

Rear Seats

Rear Head Restraint Adjustment

The vehicle’s rear seats have
adjustable head restraints in the
outboard seating positions.

The height of the head restraint can
be adjusted. Pull the head restraint up
to raise it. Try to move the head
restraint to make sure that it is locked
in place.

To lower the head restraint, press the
button, located on the top of the
seatback, and push the head restraint

down. Try to move the head restraint
after the button is released to make
sure that it is locked in place.

Always adjust the head restraint so
that the top of the restraint is at the
same height as the top of the
occupant’s head.

Rear outboard head restraints are not
removable.

If you are installing a child restraint
in the rear seat, see “Securing a Child
Restraint Designed for the LATCH
System” under Lower Anchors and

Tethers for Children (LATCH System)
0 83.

Front Seats

Seat Adjustment

Warning

{

You can lose control of the vehicle
if you try to adjust a driver seat
while the vehicle is moving. Adjust
the driver seat only when the
vehicle is not moving.

Warning

{

The power seats will work with the
ignition off. Children could operate
the power seats and be injured.
Never leave children alone in the
vehicle.

To adjust a power seat:

.

Move the seat forward or rearward
by sliding the control forward or
rearward.

.

Raise or lower the front part of the
seat cushion by moving the front
of the control up or down.

.

Raise or lower the entire seat by
moving the rear of the control up
or down.

To adjust the seatback, see Reclining
Seatbacks 0 47.

To adjust the lumbar support, see
Lumbar Adjustment 0 47.

Some vehicles are equipped with a
feature that activates a vibration in
the driver seat to help the driver avoid
crashes. See Driver Assistance Systems
0 210.

Lumbar Adjustment

Press and hold the control forward to
increase or rearward to decrease
support.

SEATS AND RESTRAINTS 47

Reclining Seatbacks

Warning

{

Sitting in a reclined position when
the vehicle is in motion can be
dangerous. Even when buckled up,
the seat belts cannot do their job.

The shoulder belt will not be
against your body. Instead, it will be
in front of you. In a crash, you
could go into it, receiving neck or
other injuries.

The lap belt could go up over your
abdomen. The belt forces would be
there, not at your pelvic bones. This
could cause serious internal
injuries.

For proper protection when the
vehicle is in motion, have the
seatback upright. Then sit well back
in the seat and wear the seat belt
properly.

48 SEATS AND RESTRAINTS

.

Tilt the top of the control
rearward to recline.

.

Tilt the top of the control forward
to raise.

Memory Seats

Do not have a seatback reclined if the
vehicle is moving.

If equipped, memory seats allow two
drivers to save and recall their unique
seat positions for driving the vehicle,
and a shared exit position for getting
out of the vehicle. Other feature
positions may also be saved, such as
power mirrors and power steering

To adjust:

wheel, if equipped. Memory positions
are linked to RKE transmitter 1 or 2
for automatic memory recalls.

Before saving, adjust all available
memory feature positions. Turn the
vehicle on and then press and release
SET; a beep will sound. Then
immediately press and hold 1, 2,

or

B (Exit) until two beeps sound.

To manually recall these positions,
press and hold 1, 2, or

saved position is reached. Follow the
instructions under “Saving Memory
Positions.”

The vehicle identifies the current
driver’s RKE transmitter number
(1–8). See Remote Keyless Entry (RKE)
System Operation 0 10. Only RKE
transmitters 1 and 2 can be used for
automatic memory recalls. A Driver
Information Center (DIC) welcome
message indicating the transmitter
number may display for the first few
ignition cycles following a transmitter
change. For Seat Entry Memory to
work properly, save the positions to
the memory button (1 or 2) matching
the RKE transmitter number displayed
in the DIC welcome message. Carr y
the linked RKE transmitter when
entering the vehicle.

B until the

Vehicle Personalization Settings

.

To have the Seat Entry Memory
movement begin when the vehicle
is started, select the Settings
menu, then Vehicle, then Seating
Position, and then Seat Entr y
Memory. Select On or Off. See
“Seat Entry Memory” later in this
section.

.

To begin Seat Exit Memor y
movement when the vehicle is
turned off and the driver door is
opened, or when the vehicle is
turned off with the driver door
already opened, select the Settings
menu, then Vehicle, then Seating
Position, and then Seat Exit
Memory. Select On or Off. See
“Seat Exit Memory” later in this
section.

.

See Vehicle Personalization 0 134
for additional setting information.

Identifying Driver Number

To identify the driver number:

1. Move your RKE transmitter away
from the vehicle.

2. Start the vehicle with another
key or RKE transmitter. The DIC
should display the driver number
for the other RKE transmitter.
Turn the vehicle off and remove
the key or RKE transmitter from
the vehicle.

3. Start the vehicle with the initial
key or RKE transmitter. The DIC
should display the driver number
of your RKE transmitter.

Saving Memory Positions

Read these instructions completely
before saving memory positions.

To save preferred driving positions
1 and 2:

1. Turn the vehicle on or to ACC/
ACCESSORY.

A DIC welcome message may
indicate driver number 1 or 2.

2. Adjust all available memory
features to the desired driving
position.

3. Press and release SET; a beep
will sound.

SEATS AND RESTRAINTS 49

4. Immediately press and hold the
1 or 2 memory button matching
the above DIC welcome message
until two beeps sound.

If too much time passes between
releasing SET and pressing 1, the
memory position will not be
saved and two beeps will not
sound. Repeat Steps 3 and 4.

1 or 2 corresponds to the driver
number. See “Identifying Driver
Number” previously in this
section.

5. Repeat Steps 1–4 for a second
driver using 1 or 2.

To save the position for
Exit Memory features, repeat Steps 1–

4 using
for getting out of the vehicle.

Save preferred memory feature
positions to both 1 and 2 if you are
the only driver.

B. This saves the position

B and Seat