Контроллер хантер эко логик инструкция

Предложите, как улучшить StudyLib

(Для жалоб на нарушения авторских прав, используйте

другую форму
)

Eco-Logic

4-& 6-Station Indoor Controller

Owners Manual and Programming Instructions

Weather Sensor

Installation Instructions

Remove lower access cover. Place a screw into the wall and hang the controller from the

keyhole on the back. Secure the controller using one or more screws below the terminal

strip. One wire from each solenoid should be connected to the C terminal (common wire).

The other wire from each solenoid to its respective number on the terminal strip. Connect

the transformer wires to the 24 VAC terminal strip. Attach the two sensor wires (if needed)

to the SEN terminals. Connect a 9-volt alkaline battery (not included) to the battery wire

clip. Plug the transformer into a nearby power outlet.

Main Display

Current Time/Day – Set current day and time.

Start Times – Set 1 to 4 start times for each program.

Run Times – Set each valve station run time from 1 min. to 4 hrs.

Water Days – Select specific days to water, odd/even days, or a selected number

of days between waterings (interval).

Seasonal Adjustment – Make run time changes according to the seasons without

reprogramming the controller.

System Off – Stops all automatic watering.

Program Designator – identifies program in use (A or B).

Flashing Sprinkler – indicates that watering is occurring.

Umbrella – indicates rain sensor is suspending irrigation.

Crossed Umbrella – Indicates rain sensor has been manually bypassed.

– identifies month when programming current date.

– identifies day when programming current date.

Manual Single Station – indicates the one time watering of a single valve station.

1

Manual All Station – indicates the one time watering of all valve stations or selected

stations.

System Off

Seasonal

Adjustment

A

B

Water Days

Control Buttons

Button – increases displayed item.

Button – decreases the displayed item.

Button – advances to the next item.

Button – advances to the previous item.

Button – Select program A or B for different watering requirements.

Mode Button – Advanced through programming functions.

Programming the Controller

An irrigation program consists of three parameters:

1) A program start time, 2) watering duration for each station and 3) days to water. A

program will run all stations assigned to it in sequential order. Programs are independent

and stations can be assigned to both programs.

Setting the Current Date and Time

1. Press the

Mode button until the arrow is pointing at the Current Time/Day

position.

2. The year will be flashing. Use the

button to proceed to setting the month.

3. The month will be flashing and the

buttons to change the month. Press the

4. The day will be flashing and the

tons to change the day. Press the

5. The time will be displayed. Use the

24 hour. Press the

button to set the hour.

MasterValve

%

AM

PM

24

RST

SEN

C

MV

1

2

3

4

5

6

24VAC

9 VOLT

ALKALINE

BATTERY

24VAC

Current

Time/Day

%

AM

PM

Start Times

24

1

Run Times

or

buttons to change the year. Press the

icon will be displayed. Use the

button to proceed to setting the day.

icon will be displayed. Use the

button to proceed to setting the time.

and

buttons to select AM, PM, or

6. Hours will be flashing. Use the

the

button to move to minutes.

7. Use the

and

have now been set.

Valve 4

Setting the Program Start Time(s)

Valve 3

NOTE: One start time will activate all stations sequentially in that program. This

eliminates the need to enter each station’s start time. Multiple start times in a

Valve 2

program can be used for separate morning, afternoon, or evening watering cycles.

Valve 1

1. Press the

2. Program A will be displayed. (If Program B is desired, press the

3. Use the

or

4. Press the

button to add an additional start time, or

program.

Eliminating a Program Start Time

With the arrow pointing at the Start Times position, press the

you reach 12:00 AM. Push the

Setting Station Run Times

1. Press the

2. Use the

button to select a program (A or B).

3. Press the

or

Press the

button to advance to the next station.

Setting Days to Water

1. Press the

2. Use the

button to select the desired program.

3. Arrows point at the specific days of the week in which watering is to occur. Press

the

button to activate that day or the

Selecting Odd or Even Days to Water

This feature is uses numbered days of the month for watering instead of specific days

of the week (Odd days 1st, 3rd, 5th, etc.; Even days 2nd, 4th, 6th, etc.).

1. When in the Water Days mode, press the

either ODD or EVEN on the display.

2. Press the

button to select, or the

to water.

Selecting Interval Watering

You can select interval watering from 1 to 31 days.

1. When in the Water Days mode, press the

Press the

button and the interval watering icon

a 1 will be flashing.

2. Press the

or

(1 to 31 days). This is called the interval.

The controller will water the selected program at the next start time and will then

water at the interval programmed.

Seasonal Adjustment

Seasonal Adjustment is used to make global run time changes without re-program-

ming the entire controller.

1. Press the

2. Press the

or

from 10% to 150%.

NOTE: The controller should always be initially programmed in

the 100% position.

System Off

To turn your controller off, press the

the System Off

watering will be shut off. All active programs will be discontinued and watering

stopped. To return the controller to normal automatic operation, simply press the

Mode button once. The current time and day will be displayed.

Programmable Off

This feature will stop all programmed waterings for a designated period of time from

1 to 7 days. After the programmed off period, the controller will automatically resume

or

programmed watering.

1. Press the

or

but-

function.

2. Wait 2 seconds until OFF is displayed.

3. Press the

button to set the number of days off (up to 7 days).

and

buttons to change the hour shown. Press

buttons to change the minutes shown. The date, day and time

Mode button until the arrow is pointing at Start Times

buttons to change the start time.

button once to reach the OFF position.

Mode button until the arrow is pointing at Run Times

buttons to change the station run time from 1 minute to 4 hours.

Mode button until the arrow is pointing at Water Days

button to cancel watering for that day.

button until the cursor is above

button to cancel either ODD or EVEN days

button until the cursor is over INT.

button to select the number of days between watering days

Mode button until the arrow is pointing at Seasonal Adjustment

buttons to adjust the percentage of the seasonal adjustment

Mode button until the arrow is pointing at

. Wait 2 seconds and the display will read OFF. Valves currently

Mode button until the arrow is positioned next to the System Off

.

button).

button for the next

or

buttons until

.

.

will be displayed and

.

Таймер автоматического полива Hunter Eco Logic идеально подходит для установки на небольшие приусадебные участки и управления автополивом.

Инструкция по настройке

Посмотрите видео инструкцию, как настраивать конторллер

Невысокая цена, высокий функционал автоматического таймера для полива, легкая программируемость, широкий выбор настроек. Все это вы получаете приобретая пульт ECO LOGIC.

Пульт управления превосходно работает в паре с насосом Espa Tecnopres 25 4m.

Фирма Hunter специально разработала данный вид пультов, чтобы владельцы любых участков, даже с небольшим бюджетом, могли установить себе систему автоматического полива.

Как происходит настройка

Всего 1 раз вы настраиваете систему и целый год наслаждаетесь результатами ее работы.

За все это отвечает компьютер, безошибочно точно распределяющий расход воды в системе орошения.

Hunter — фирма из США, давно зарекомендовавшая себя на рынке поливочного оборудования.

Существует альтернативный автоматический контроллер полива RZX-4i от Rain Bird

Гарантия

Гарантия на все устройства и механизмы составляет 2 года с момента установки.

Таймеры Eco Logic расчитаны на 4 или 6 зон. Устанавливать пульт нужно в помещении.

Как экономить свое время и силы

Если вам требуется внешний контроллер, обратитесь к пульту управления X-Core

Установите систему автополива на своем участке и дайте растениям возможность расти без вашего участия — экономьте 100% своего времени затрачиваемого на орошение.

Звоните сейчас или оставьте заявку на сайте. Наш менеджер ответит на все ваши вопросы и даст подробную консультацию.

Получите бесплатно расчет стоимости системы автоматического полива сейчас.

Instructions AWS – Hunter model

How to use the eco-logic controller

• Use the mode button to advance through the programming functions.

• Use the arrows to move about the different fields within a function and the plus and minus

button to change the value that’s currently flashing.

• The PRG button is used to advance from program A to program B and program C.

Set the current date and time

• Press the mode button on and the year will start flashing

• Use the left and right arrow buttons to scroll through the different choices. Tapping the right

arrow button once will show the month.

• Use the minus and plus button to change to the current month.

• Use the right arrow button to sellect the correct day.

• By tapping the plus (+) button you can switch to a.m./p.m. or 24-hour mode.

• When you come back to the years that’s a complete cycle. You can use the mode button to

go back to the home screen, which shows the current timer.

Set the automatic water refreshment

A program is a group of stations that share the same watering schedule. By schedule we mean

watering days of the week on which the program will run as well as the number of times the program

will cycle per watering day. If all your stations will be watering in the same days and the same

number of times a day then you can program all your stations in the same program, which we

strongly advice.