Металлоискатель go find 44 инструкция по применению

DETECTING BASICS

QUICK START GUIDE

STEP 1. POWER ON

Switch your detector on.

The LCD will light up with several icons.

STEP 2. BEGIN DETECTING

Sweep the coil over the ground in a side-to-side motion.

The detector will light up and beep when a metal object is found.

SWEEP LEVEL Keep the coil 1–2

inches (2–3 cm) above and parallel to

the ground at all times.

SPEED Sweep the coil over the

ground in a side-to-side motion, an

average sweep speed is 1–2 seconds

from left to right.

OVERLAP SWEEP Slightly overlap the

previous sweep to ensure full ground

coverage.

CONTROL PANEL

10

11

12

1

2

3

1) POWER SWITCH (ON/OFF)

2) EAR BUDS OUTPUT

3) SENSITIVITY

Increase for more detecting depth. You

may need to decrease this if there is high

noise interference or false signals.

4) PINPOINT (GO‑FIND 40/60 only)

Determine the exact location of a target.

5) VOLUME

6) BACKLIGHT (GO‑FIND 40/60 only)

7) FIND MODE

Detect and reject metal objects.

ON switch

ITEM FOUND The detector will

light up and beep when a target is

discovered.

ADJUSTMENT The detector should

be straight with your forearm and

feel light and comfortable when you

pick it up.

50 ft (15 m)

SPACE Recommended distance is

50 feet (15 m) apart when multiple

users are scanning an area.

9

8

7

6

5

4

DEPTH INDICATION

Shallow | Medium | Deep

9) TREASURE VIEW LED

Red and green LEDs help you quickly

identify treasure from trash.

(GO‑FIND 40/60 only)

10) FIND ICONS (x 4)

11) BATTERY LEVEL

12) BLUETOOTH (GO‑FIND 40/60 only)

AUDIO OUTPUT

1/8″ connector with speaker at rear.

TREASURE VIEW

(GO‑FIND 40/60 only)

Treasure View LEDs light up when a metal object has been detected.

As you get closer to the target, more LEDs illuminate.

RED indicates an iron metal object (possibly trash).

GREEN indicates a non-iron metal object (possibly treasure).

ORANGE indicates Pinpoint mode for all metal objects.

LEDs will illuminate from left to right when Pinpoint is off.

LEDs will illuminate towards the center when Pinpoint in on.

This helps identify the exact location of the object.

ICON DESCRIPTIONS

When a metal object is detected, the corresponding icon will flash on

the control panel to indicate the target type. If the icon is turned off (not

visible) then these object types will not be detected.

E.g. Iron objects, nails and

horseshoes.

E.g. Aluminium foil and lower

value coins.

FIND MODES

FIND modes allow you to search for specific groups of metal objects by

accepting or rejecting detection. No need to dig the trash – just the treasure!

Cycle through the different modes using the Find button.

GO‑FIND 20

GO‑FIND 40

Select from 2 find modes:

Select from 3 find modes:

1)

1)

2)

2)

3)

DETECTOR SOUNDS

The detector beeps when an object is detected. This sound can be heard

through the detector speaker or through ear buds/headphones connected to

the audio output socket (refer to control panel diagram).

GO‑FIND 20

GO‑FIND 40

2 different audio tones:

3 different audio tones:

LOW TONE: Iron targets (such as nails) produce the lowest tone.

MID 1 TONE (GO‑FIND 40/60 ONLY): Less valuable metals produce a lower medium tone.

MID 2 TONE (GO‑FIND 60 ONLY): Higher value metals produce a higher medium tone.

HIGH TONE: Silver and copper targets produce the highest tone.

E.g. Rings, pull tabs and lower

value coins.

E.g. Low and high value coins

and screw caps.

GO‑FIND 60

Select from 4 find modes:

1)

2)

3)

4)

GO‑FIND 60

4 different audio tones: