Pax s80 инструкция по эксплуатации

1. Manuals
2. Brands
3. PAX Manuals
4. Touch terminals
5. S80
6. User manual

• Contents

• Table of Contents

• Troubleshooting

• Bookmarks

Summary of Contents for PAX S80

CONNECTING THE TERMINAL

Hold the PAX S80 face down on a table or work place.

Plug the power adapter connector into the S80 «Power» jack (middle).

Plug the PAX S80 power cord into the available electrical outlet or power bar.

Plug the required communication cord(s) into the proper sockets.

Plug the Ethernet cable into the «LAN» socket, and/or plug telephone

line cable into the «LINE» socket.

Switch the terminal on by pressing the Power button.

LOADING & CHANGING THE PAPER ROLL

Press the green paper cover release button and open the paper roll cover.

Place the paper roll in the compartment making sure the paper feeds from

the underside of roll, towards the paper tear bar.

Pull the end of the paper out of the compartment beyond the tear bar and

close paper roll cover.

Keypad Layout

2 Scroll button

8 Power button

7 Cancel buy

Set-Up Guide

F1 Soft button

F2 Soft button

1

F3 Soft button

F1 Soft button

2 Scroll button

3 Fonction button

4 Menu button

5 Enter button

6 Clear button

PAX S80

R5232A PINPAD

LAN /

LINE

POWER

Menu Layout

Power button is used to switch

terminal on/off.

The PAX S80 menu functions are

arranged in two menus:

Transaction and Administration.

Scroll buttons are used to scroll

through to display menu options.

To access letters on the numeric

keypad, press the key quickly until

the desired letter appears.

Press 0 (zero) twice for space,

•

Up button for [

] and Down

•

twice for [

]

Use yellow Corr button to go back

one step.

1

Product Description

1

Product Description

Figure 1 Top View

Figure 2 Bottom View

Figure 3: SAM/SIM Socket Figure 4 Ports at Bottom

Figure 5: S80 Wall Mounting Device

Note: The above figure shows S80 equipped Wall Mounting Device

which is optional.

Installation

2

Installation

1) Place S80 on table

2) Connect the attached cable

Remove port cover on bottom of S80

Connect each plug of the attached cables into the

corresponding sockets on the rear panel of the terminal.

Put the port cover back.

SAM PINPAD

RS232A

Power

LINE

LAN /RS232B

SIM

3) Insert the telephone cord supplied with the terminal into

standard RJ-11 type outlet. Connect the other end of the

telephone cord into a standard RJ-11 type modular

telephone line outlet.

The figure below shows cable installation.

4) Connect serial facility to RS232 socket.

5) Connect AC plug of power adaptor into AC socket.

6) Place paper roll into S80

Press the paper cover release key to open paper cover.

Insert paper roll along the arrow.

Lead the paper out and place the paper on paper cut and

push the paper cover downward until a sound of ka can

Instruction

3

Instruction

be heard.

7) Turn on S80, LCD backlight is on. On screen initialization

and application interface show on one after another.

To perform a simulation of transaction successfully thus

S80 installation is OK.

1) Power on/off

Power on: Press the red button for about 2 seconds until

LED backlight on, the POS is on.

Power off: Press the red button for about 2 seconds until the

content of display vanishes, the POS is off.

2) Magnetic swipe

When pulling a magnetic card along the slot, make the

magnetic stripe face the machine. Bi-directional pulling the

magnetic card is acceptable. It is recommended from up to

down, and with a steady speed.

3) IC card operational description

When insert a card, make the contact of the card upward.

Gently insert and withdraw the card In order to protect the

contact on card and IC card connector.

4) Tear paper operation

Hold the end of paper along with the paper cut as an angle

of 45 degree and swiftly and evenly tear the paper off.

POS Wall

POS

Wall Mounting Device Wall Wall Mounting Device

Paper cover

LCD display

On/off Key

Paper cover

release key

ATM-style key

Keypad

IC Card slot

Privacy shield(Opt.)

Paper cutter

PAX TECHNOLOGY LIMITED reserves

the right to change product technology

specifications without notifying.

Room 2416, 24/F., Sun Hung Kai Centre, 30

Harbour Road, Wanchai, Hong Kong

Tel: +852-2588 8808 Fax: +852-2802 3300

E-mail: daniel@pax.com.hk

Website: www.pax.com.hk

PAX TECHNOLOGY LIMITED

®

®®

Magnetic strip

card slot

Hang hole(Opt.)

Port cover

Nameplate

USB port

Bar code lable

SAM/SIM socket cover

Power

Contactless Card Reader

Interface

Screw

S80S80

S80

Handover

Countertop Payment Terminal

Installation Manual

PAX TECHNOLOGY LIMITED

Specification

Specification

5

1) Use a power bar well grounded and with a fuse in it.

2) Protect power supply cable and power adaptor. If they are

broken, they are no longer be used.

3) Before connect power bar to AC socket, make sure the

voltage is correct as POS states.

4) POS should be placed steady on table. It is not allowed

make it under sun beam, high temperature, high humidity or

place full of dust.

5) Keep it away from liquid.

6) Don’t insert hard stuff into port which may damage POS

severely.

7) When a POS is in failure, please contact designated

personnel to maintain it. It is not allowed to repair it on your

own.

When insert paper roll, do not touch paper cut and protect

your finger from being hurt.

9) Only use designated paper roll to avoid paper jam or

damaging the printer.

Notice at Installation and Use

4

Notice at Installation and Use

Default

CPU: 32-bit ,ARM9

Memory: 8MB Flash, 16MB SDRAM

Display: 128 x 64 pixel LCD, LED backlight

Keypad: 10 alphanumeric keys, 8 functional keys,

4 ATM keys, 1 switch(on) key

ISO7812, Track 1/2/3,

bi-directional swipe

IC Card Reader: 1, EMV2000 compliant

SAM Slots: 3, ISO7816

Modem: Sync. (

)

Async. (V.92, )

Peripheral Ports: 1 RS232, 1 PIN Pad, 1 line port,

1 Phone port

Printer: Thermal printer, Speed: 20 lines/sec,

Paper width: 57mm

Paper roll outer diameter: 50mm

Power Supply: Input 100-240VAC, 50Hz/60Hz, 1.5A

Output 8.2VDC, 5A

Working Environment: Temperature:0 40 (

R.H. :10% 90%(non-condense)

Storage Environment: Temperature:-20 70 (

R.H. :5% 95% non-condense

Dimensions: 216mm x 95mm x 86mm (L x W x H,

including the keypad privacy shield)

Weight 525g

Optional:

Built-in Ethernet module

HDLC up to 9600bps,

V.21,V.22/V.22bis,V.29

up to 56Kbps

, 1 USB port

32 104 )

-4 150 )

Built-in GPRS module

Mass storage: 128MB

Contactless Card Reader (Can connect with an external

contactless card reader as an integrated

design of POS system. ISO/IEC14443

Type A/B, 4 LEDs RF Indicator)

PIN Protection

PIN Protection

The following techniques can be employed to provide for

effective screening of the PIN-entry during the PIN entry

process. These methods would typically be used in combination,

though in some cases a method might be used singly.

Positioning of terminal on the check-stand in such way as to

make visual observation of the PIN-entry process infeasible.

Examples include:

Installing PED on an adjustable stand that allows consumers to

process difficult.

Positioning of in-store security cameras such that the PIN-entry

keypad is not visible.

Post instructions around check-stand, in order to inform

customers. Instructing the cardholder regarding safe PIN-entry.

When the cardholder input his/her PIN, he/she had better use

his/her body and hands to prevent visual observation of PIN-

entry process.

-Visual shields designed into the check-stand. The shields

may be solely for shielding purposes, or may be part of

the general check-stand design, e.g., used as selling

area.

-Position the PED so that it is angled in such a way to

make PIN spying difficult.

Note *Customer instruction methods are less repeatable and

therefore should be used in combination with other methods.

Security levels: L = low M = medium H = high

S80 PIN-entry observation corridors v.s. PIN protection methods

Customers

in Queue

Cashier Customers

Elsewhere On-Site

Camera Remote

Cameras

Observation Corridors

Method

S80 on

Adjustable Stand

Post Customer

Instruction

S80 in Check-Stand

with shield

swivel the terminal sideways and/or tilt it forwards/backwards to

a position that makes visual observation of the PIN-entry

® ®

®

Note To protect the process of PIN-entry, it is not limited to the

above methods and examples, merchants also can adopt other

methods and steps to keep cardholder’s PIN safe.

Magnetic Card Reader:

CAUTION To reduce the risk of fire, use only No.26 AWG

or larger telecommunication line cord

Note: RSS232 Port only used as upgraded EUT by manufacturer

Warning：

We declare that:

※ The FCC ID label is placed on Payment Terminal clearly visible to all persons at the

time of purchase.

※ The user is cautioned that changes or modifications not expressly approved by the

manufacturer could void the user’s authority to operate the equipment.

※ This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

※ Do not attempt to disassemble the Payment Terminal by yourself.Non-expert

handling of the devices may damage them.

※ Your Payment Terminal is a radio transmitter and receiver. It is designed and

manufactured not to exceed limits for exposure to radio frequency (RF) energy set by the

Federal Communications

※ Commission (FCC) of the U.S. Government. These limits are part of comprehensive

guidelines and establish permitted levels of RF energy for the general population. The

guidelines are based on standards that were developed by independent scientific

organizations through periodic and thorough evaluation of scientific studies. The

standards include a substantial safety margin designed to assure the safety of all persons,

regardless of age or health. The exposure standard for Payment Terminal employs a

unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limits set

by the FCC are 1.6 W/Kg. Tests for SAR are conducted using standard operating positions

accepted by the FCC with the Payment Terminal transmitting as its highest certified

power level in all tested frequency bands. Although the SAR is determined at the highest

certified power level, the actual SAR level of the phone while operating can be well below

the maximum value. This is because the Payment Termina is designed to operate at

multiple power levels so as to use only the power required to reach the network. In

general, the closer you are to a wireless base station, the lower the output power.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment .

Note: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more

of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.