Pioneer mvh s520bt инструкция по подключению

Connections

In the following, «NW» represents network mode and «STD» represents standard mode. According to the connections you have established, change the speaker mode to standard mode (STD) or network mode (NW).

• When installing this unit in a vehicle without an ACC (accessory) position on the ignition switch, failure to connect the red cable to the terminal that detects operation of the ignition key may result in battery drain.
  
• Use of this unit in conditions other than the following could result in fire or malfunction.
  • Vehicles with a 12-volt battery and negative grounding.
  • When speaker output is used by 4 channels, use speakers over 50 W (maximum input power) and between 4 Ω to 8 Ω (impedance value). Do not use 1 Ω to 3 Ω speakers for this unit.
  • When rear speaker output is used by 2 Ω of subwoofer, use speakers over 70 W (maximum input power).
    * Please refer to connections for a connection method.
• To prevent a short-circuit, overheating or malfunction, be sure to follow the directions below.
  • Disconnect the negative terminal of the battery before installation.
  • Secure the wiring with cable clamps or adhesive tape. Wrap adhesive tape around wiring that comes into contact with metal parts to protect the wiring.
  • Place all cables away from moving parts, such as the shift lever and seat rails.
  • Place all cables away from hot places, such as near the heater outlet.
  • Do not connect the yellow cable to the battery by passing it through the hole to the engine compartment.
  • Cover any disconnected cable connectors with insulating tape.
  • Do not shorten any cables.
  • Never cut the insulation of the power cable of this unit in order to share the power with other devices. The current capacity of the cable is limited.
  • Use a fuse of the rating prescribed.
  • Never wire the negative speaker cable directly to ground.
  • Never band together negative cables of multiple speakers.
• When this unit is on, control signals are sent through the blue/white cable. Connect this cable to the system remote control of an external power amp or the vehicle’s auto-antenna relay control terminal (max. 300 mA 12 V DC). If the vehicle is equipped with a glass antenna, connect it to the antenna booster power supply terminal.
• Never connect the blue/white cable to the power terminal of an external power amp. Also, never connect it to the power terminal of the auto antenna. Doing so may result in battery drain or a malfunction.
• The graphical symbol placed on the product means direct current.

This unit

1. Microphone (3 m)
2. Power cord input
3. Microphone input
4. Rear output (STD) or middle range output (NW)
5. Front output (STD) or high range output (NW)
6. Antenna input
7. Fuse (10 A)
8. Wired remote input
   Hard-wired remote control adapter can be connected (sold separately).
9. Subwoofer output

Removing the unit (installed with the supplied mounting sleeve)

1. Remove the trim ring.
   
   1. Trim ring
   2. Notched tab
   • Releasing the front panel allows easier access to the trim ring.
   • When reattaching the trim ring, point the side with the notched tab down.
2. Insert the supplied extraction keys into both sides of the unit until they click into place.
3. Pull the unit out of the dashboard.
   

Installing the microphone

The microphone should be placed directly in front of the driver at a suitable distance to pick up their voice clearly.

It is extremely dangerous to allow the microphone lead to become wound around the steering column or shift lever. Be sure to install the microphone in such a way that it will not obstruct driving. It is recommended to use the clamps (sold separately) to arrange the lead.

NOTE
Depending on the vehicle model, the microphone cable length may be too short when you mount the microphone on the sun visor. In such cases, install the microphone on the steering column.

To install on the sun visor

1. Fit the microphone lead into the groove.
   
   1. Microphone lead
   2. Groove
2. Install the microphone clip on the sun visor.
   Lowering the sun visor reduces the voice recognition rate.
   
   1. Microphone clip

Basic operation

MVH-S520BT

About the main menu

You can adjust various settings in the main menu.

1. Press the M.C. dial to display the main menu.
2. Turn the M.C. dial to select one of the categories below, then press to confirm.
   • FUNCTION settings
   • AUDIO settings
   • SYSTEM settings
   • ILLUMINATION settings
   • MIXTRAX settings
   • MICROPHONE settings
3. Turn the M.C. dial to select the options, then press to confirm.

Frequently used operations

Purpose	Operation
Turn on the power	Press SRC/OFF to turn on the power. Press and hold SRC/OFF to turn off the power.
Adjust the volume	Turn the M.C. dial.
Select a source	Press SRC/OFF repeatedly.
Change the display information	Press DISP repeatedly.
Return to the previous display/list	Press BAND/.
Return to the normal display from the menu	Press and hold BAND/ .
Change the display brightness	Press and hold BAND/ .

Setup operation

When you turn the ignition switch to ON after installation, the setup menu appears in the display.

Do not use the unit in standard mode when a speaker system for network mode is connected to the unit. Do not use the unit in network mode when a speaker system for standard mode is connected to the unit. This may cause damage to the speakers.

1. Turn the M.C. dial to select the options, then press to confirm.
   To proceed to the next menu option, you need to confirm your selection.

1. [QUIT:YES] appears.
   To return to the first item of the setup menu, turn the M.C. dial to select [QUIT:NO], then press to confirm.
2. Press the M.C. dial to confirm the settings.

MTP connection

A device installed with Android OS 4.0 or most of later versions can be connected to the unit via MTP, using the cable supplied with the Android device. However, depending on the connected device, OS version or the numbers of the files in the device, audio files/songs may not be able to be played back via MTP.

NOTE
If you use an MTP connection, [USB MTP] needs to be set to [ON] in the SYSTEM settings.

AUX

1. Insert the stereo mini plug into the AUX input jack.
2. Press SRC/OFF to select [AUX IN] as the source.

Bluetooth connection

Up to two Bluetooth telephones can be connected simultaneously.

1. Turn on the Bluetooth function of the device.
2. Select the unit name shown in the device display.
3. Make sure the same 6-digit number appears on this unit and the device.
4. Select [YES].

Bluetooth telephone

Basic operations

Activating voice recognition mode

1. Press and hold and then talk into the microphone to input voice commands.

To exit the voice recognition mode, press BAND/.

Making a connection with Pioneer Smart Sync

Pioneer Smart Sync is the application that intelligently brings your maps, messages, and music together in the vehicle.

Do not attempt to operate the application while driving. Make sure to pull off the road and park your vehicle in a safe location before attempting to use the controls on the application.

1. Enter the SYSTEM menu (refer to «About the main menu»).
2. Turn the M.C. dial to select [APP CONTROL], then press to confirm.
3. Turn the M.C. dial to select one of the below.
   • Select [WIRED] for the USB connection.
   • Select [BLUETOOTH] for the Bluetooth connection.
4. Turn the M.C. dial to select [AUTO APP CONN], then press to confirm.
5. Turn the M.C. dial to select [ON], then press to confirm.
6. Connect this unit with the mobile device via USB or Bluetooth. Pioneer Smart Sync on the iPhone/Android device starts automatically.
   NOTE
   Regardless of whether the [AUTO APP CONN] setting is set to [ON] or [OFF], you can also perform the following to start Pioneer Smart Sync.
   • For devices other than the USB-connected Android device, press SRC/OFF to select any source and press and hold the M.C. dial.
   • For iPhone, launch Pioneer Smart Sync on the mobile device.

Listening to Spotify^®

(Not available when [USB MTP] is set to [ON] in the SYSTEM settings.)

Update the firmware of the Spotify application to the latest version before use.

Before you start, connect this unit with the mobile device via USB (iPhone only) or Bluetooth.

1. Enter the SYSTEM menu (refer to «About the main menu»).
2. Turn the M.C. dial to select [APP CONTROL], then press to confirm.
3. Turn the M.C. dial to select one of the below.
   • Select [WIRED] for the USB connection.
   • Select [BLUETOOTH] for the Bluetooth connection.
4. Press SRC/OFF to select [SPOTIFY].
5. Launch the Spotify application on the mobile device and start playback.

• Главная
• Продукция
• Автомобильные ресиверы
• Support for MVH-S520BT

Basic operation

MVH-S520BT

M.C. (multi-control) dial

SRC (source)/OFF

BAND/

(navigation)/LIST

Frequently used operations

Purpose

Turn on the power*

Adjust the volume

Select a source

Change the display information

Return to the previous display/list

Return to the normal display from the menu Press and hold BAND/

Change the display brightness

Answering a call

Ending a call

* When this unit’s blue/white lead is connected to the vehicle’s auto-antenna relay control terminal,

the vehicle’s antenna extends when this unit’s source is turned on. To retract the antenna, turn the

source off.

DISP (display)

Display window

AUX input jack (3.5 mm stereo jack)

— 3 —

— 3 —

Detach button

Operation

Press SRC/OFF to turn on the power.

Press and hold SRC/OFF to turn off the

power.

Turn the M.C. dial.

Press SRC/OFF repeatedly.

Press DISP repeatedly.

Press BAND/

.

Press and hold BAND/

Press any button.

Press

.

USB port

.

.