Рефлектометр оптический exfo ftb 200 инструкция

Copyright © 2010–2014 EXFO Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form, be it electronically, mechanically, or by any other means such as photocopying, recording or otherwise, without the prior written permission of EXFO Inc. (EXFO).

Information provided by EXFO is believed to be accurate and reliable. However, no responsibility is assumed by EXFO for its use nor for any infringements of patents or other rights of third parties that may result from its use. No license is granted by implication or otherwise under any patent rights of EXFO.

EXFO’s Commerce And Government Entities (CAGE) code under the North Atlantic Treaty Organization (NATO) is 0L8C3.

The information contained in this publication is subject to change without notice.

Trademarks

EXFO’s trademarks have been identified as such. However, the presence or absence of such identification does not affect the legal status of any trademark.

Units of Measurement

Units of measurement in this publication conform to SI standards and practices.

Version number: 18.0.3

End-User License Agreement

You have acquired a device («DEVICE») that includes software licensed by EXFO Inc. (EXFO) from an affiliate of Microsoft Corporation («MS»). Those installed software products of MS origin, as well as associated media, printed materials, and «online» or electronic documentation («SOFTWARE») are protected by international intellectual property laws and treaties. Manufacturer, MS and its suppliers (including Microsoft Corporation) own the title, copyright, and other intellectual property rights in the SOFTWARE. The SOFTWARE is licensed, not sold. All rights reserved.

This EULA is valid and grants the end-user rights ONLY if the SOFTWARE is genuine and a genuine Certificate of Authenticity for the SOFTWARE is included. For more information on identifying whether your software is genuine, please see http://www.microsoft.com/piracy/howtotell.

IF YOU DO NOT AGREE TO THIS END USER LICENSE AGREEMENT («EULA»), DO NOT USE THE DEVICE OR COPY THE SOFTWARE. INSTEAD, PROMPTLY CONTACT EXFO FOR INSTRUCTIONS ON RETURN OF THE UNUSED DEVICE(S) FOR A REFUND. ANY USE OF THE SOFTWARE, INCLUDING BUT NOT LIMITED TO USE ON THE DEVICE, WILL CONSTITUTE

YOUR AGREEMENT TO THIS EULA (OR RATIFICATION OF ANY PREVIOUS CONSENT). GRANT OF SOFTWARE LICENSE. This EULA grants you the following license:

You may use the SOFTWARE only on the DEVICE.

Restricted Functionality. You are licensed to use the SOFTWARE to provide only the limited functionality (specific tasks or processes) for which the DEVICE has been designed and marketed by EXFO. This license specifically prohibits any other use of the software programs or functions, or inclusion of additional software programs or functions that do not directly support the limited functionality on the DEVICE. Notwithstanding the foregoing, you may install or enable on a DEVICE, systems utilities, resource management or similar software solely for the purpose of administration, performance enhancement and/or preventive maintenance of the DEVICE.

If you use the DEVICE to access or utilize the services or functionality of Microsoft Windows Server products (such as Microsoft Windows Server 2003), or use the DEVICE to permit workstation or computing devices to access or utilize the services or functionality of Microsoft Windows Server products, you may be required to obtain a Client Access License for the DEVICE and/or each such workstation or computing device. Please refer to the end user license agreement for your Microsoft Windows Server product for additional information.

NOT FAULT TOLERANT. THE SOFTWARE IS NOT FAULT TOLERANT. EXFO HAS INDEPENDENTLY DETERMINED HOW TO USE THE SOFTWARE IN THE DEVICE, AND MS HAS RELIED UPON EXFO TO CONDUCT SUFFICIENT TESTING TO DETERMINE THAT THE SOFTWARE IS SUITABLE FOR SUCH USE.

NO WARRANTIES FOR THE SOFTWARE. THE SOFTWARE is provided «AS IS» and with all faults. THE ENTIRE RISK AS TO SATISFACTORY QUALITY, PERFORMANCE, ACCURACY, AND EFFORT (INCLUDING LACK OF NEGLIGENCE) IS WITH YOU. ALSO, THERE IS NO WARRANTY AGAINST INTERFERENCE WITH YOUR ENJOYMENT OF THE SOFTWARE OR AGAINST INFRINGEMENT. IF YOU HAVE RECEIVED ANY WARRANTIES REGARDING THE DEVICE OR THE SOFTWARE, THOSE WARRANTIES DO NOT ORIGINATE FROM, AND ARE NOT BINDING ON, MS.

No Liability for Certain Damages. EXCEPT AS PROHIBITED BY LAW, MS SHALL HAVE NO LIABILITY FOR ANY

INDIRECT, SPECIAL, CONSEQUENTIAL OR INCIDENTAL DAMAGES ARISING FROM OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE SOFTWARE. THIS LIMITATION SHALL APPLY EVEN IF ANY REMEDY FAILS OF ITS ESSENTIAL PURPOSE. IN NO EVENT SHALL MS BE LIABLE FOR ANY AMOUNT IN EXCESS OF U.S. TWO HUNDRED FIFTY DOLLARS (U.S.$250.00).

Restricted Uses. The SOFTWARE is not designed or intended for use or resale in hazardous environments requiring fail-safe performance, such as in the operation of nuclear facilities, aircraft navigation or communication systems, air traffic control, or other devices or systems in which a malfunction of the SOFTWARE would result in foreseeable risk of injury or death to the operator of the device or system, or to others.

Limitations on Reverse Engineering, Decompilation, and Disassembly. You may not reverse engineer, decompile, or disassemble the SOFTWARE, except and only to the extent that such activity is expressly permitted by applicable law notwithstanding this limitation.

SOFTWARE as a Component of the DEVICE — Transfer. This license may not be shared, transferred to or used concurrently on different computers. The SOFTWARE is licensed with the DEVICE as a single integrated product and may only be used with the DEVICE. If the SOFTWARE is not accompanied by a DEVICE, you may not use the SOFTWARE. You may permanently transfer all of your rights under this EULA only as part of a permanent sale or transfer of the DEVICE, provided you retain no copies of the SOFTWARE. If the SOFTWARE is an upgrade, any transfer must also include all prior versions of the SOFTWARE. This transfer must also include the Certificate of Authenticity label. The transfer may not be an indirect transfer, such as a consignment. Prior to the transfer, the end user receiving the SOFTWARE must agree to all the EULA terms.

Consent to Use of Data. You agree that MS, Microsoft Corporation and their affiliates may collect and use technical information gathered in any manner as part of product support services related to the SOFTWARE. MS, Microsoft Corporation and their affiliates may use this information solely to improve their products or to provide customized services or technologies to you. MS, Microsoft Corporation and their affiliates may disclose this information to others, but not in a form that personally identifies you.

Internet Gaming/Update Features. If the SOFTWARE provides, and you choose to utilize, the Internet gaming or update features within the SOFTWARE, it is necessary to use certain computer system, hardware, and software information to implement the features. By using these features, you explicitly authorize MS, Microsoft Corporation and/or their designated agent to use this information solely to improve their products or to provide customized services or technologies to you. MS or Microsoft Corporation may disclose this information to others, but not in a form that personally identifies you.

Internet-Based Services Components. The SOFTWARE may contain components that enable and facilitate the use of certain Internet-based services. You acknowledge and agree that MS, Microsoft Corporation or their affiliates may automatically check the version of the SOFTWARE and/or its components that you are utilizing and may provide upgrades or supplements to the SOFTWARE that may be automatically downloaded to your DEVICE. Microsoft Corporation or their affiliates do not use these features to collect any information that will be used to identify you or contact you. For more information about these features, please see the privacy statement at http://go.microsoft.com/fwlink/?LinkId=25243.

Links to Third Party Sites. You may link to third party sites through the use of the SOFTWARE. The third party sites are not under the control of MS or Microsoft Corporation, and MS or Microsoft are not responsible for the contents of any third party sites, any links contained in third party sites, or any changes or updates to third party sites. MS or Microsoft Corporation is not responsible for webcasting or any other form of transmission received from any third party sites. MS or Microsoft Corporation are providing these links to third party sites to you only as a convenience, and the inclusion of any link does not imply an endorsement by MS or Microsoft Corporation of the third party site.

Notice Regarding Security. To help protect against breaches of security and malicious software, periodically back up your data and system information, use security features such as firewalls, and install and use security updates.

No Rental/Commercial Hosting. You may not rent, lease, lend or provide commercial hosting services with the SOFTWARE to others.

Separation of Components. The SOFTWARE is licensed as a single product. Its component parts may not be separated for use on more than one computer.

Additional Software/Services. This EULA applies to updates, supplements, add-on components, product support services, or Internet-based services components («Supplemental Components»), of the SOFTWARE that you may obtain from EXFO, MS, Microsoft Corporation or their subsidiaries after the date you obtain your initial copy of the SOFTWARE, unless you accept updated terms or another agreement governs. If other terms are not provided along with such Supplemental Components and the Supplemental Components are provided to you by MS, Microsoft Corporation or their subsidiaries then you will be licensed by such entity under the same terms and conditions of this EULA, except that (i) MS, Microsoft Corporation or their subsidiaries providing the Supplemental Components will be the licensor with respect to such Supplemental Components in lieu of the «COMPANY» for the purposes of the EULA, and (ii) TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE SUPPLEMENTAL COMPONENTS AND ANY (IF ANY) SUPPORT SERVICES RELATED TO THE SUPPLEMENTAL COMPONENTS ARE PROVIDED AS IS AND WITH ALL FAULTS. ALL OTHER DISCLAIMERS, LIMITATION OF DAMAGES, AND SPECIAL PROVISIONS PROVIDED BELOW AND/OR OTHERWISE WITH THE SOFTWARE SHALL APPLY TO SUCH SUPPLEMENTAL COMPONENTS. MS, Microsoft Corporation or their subsidiaries reserve the right to discontinue any Internet-based services provided to you or made available to you through the use of the SOFTWARE.

Recovery Media. If SOFTWARE is provided by EXFO on separate media and labeled «Recovery Media» you may use the Recovery Media solely to restore or reinstall the SOFTWARE originally installed on the DEVICE.

Backup Copy. You may make one (1) backup copy of the SOFTWARE. You may use this backup copy solely for your archival purposes and to reinstall the SOFTWARE on the DEVICE. Except as expressly provided in this EULA or by local law, you may not otherwise make copies of the SOFTWARE, including the printed materials accompanying the SOFTWARE. You may not loan, rent, lend or otherwise transfer the backup copy to another user.

End User Proof of License. If you acquired the SOFTWARE on a DEVICE, or on a compact disc or other media, a genuine Microsoft «Proof of License»/Certificate of Authenticity label with a genuine copy of the SOFTWARE identifies a licensed copy of the SOFTWARE. To be valid, the label must be affixed to the DEVICE, or appear on [COMPANY’s] software packaging. If you receive the label separately other than from EXFO, it is invalid. You should keep the label on the DEVICE or packaging to prove that you are licensed to use the SOFTWARE.

Product Support. Product support for the SOFTWARE is not provided by MS, Microsoft Corporation, or their affiliates or subsidiaries. For product support, please refer to EXFO support number provided in the documentation for the DEVICE. Should you have any questions concerning this EULA, or if you desire to contact EXFO for any other reason, please refer to the address provided in the documentation for the DEVICE.

Termination. Without prejudice to any other rights, EXFO may terminate this EULA if you fail to comply with the terms and conditions of this EULA. In such event, you must destroy all copies of the SOFTWARE and all of its component parts.

EXPORT RESTRICTIONS. You acknowledge that SOFTWARE is subject to U.S. and European Union export jurisdiction. You agree to comply with all applicable international and national laws that apply to the SOFTWARE, including the U.S. Export Administration Regulations, as well as end-user, end-use and destination restrictions issued by U.S. and other governments. For additional information see http://www.microsoft.com/exporting/.

Certification Information

Certification Information

North America Regulatory Statement

This unit was certified by an agency approved in both Canada and the United States of America. It has been evaluated according to applicable North American approved standards for product safety for use in Canada and the United States.

Electronic test and measurement equipment is exempt from FCC part 15, subpart B compliance in the United States of America and from ICES-003 compliance in Canada. However, EXFO Inc. makes reasonable efforts to ensure compliance to the applicable standards.

The limits set by these standards are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the user guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

Certification Information

If you purchased the Wi-Fi and Bluetooth option, your unit comes with an internal wireless module and antenna for which the following information applies:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

European Community Declaration of Conformity

An electronic version of the declaration of conformity for your product is available on our website at www.exfo.com. Refer to the product’s page on the Web site for details.

1 Introducing the FTB-200 v2

Compact Modular Platform

Optimized for all phases of the network lifecycle, the FTB-200 v2 Compact Modular Platform houses any of EXFO’s FTB oneor two-slot modules to meet your evolving needs. You can configure your platform by combining optical, transport and datacom modules to cover a wide range of applications.

Note: In this documentation, the words “tap” and “double-tap” (related to the use of a touchscreen) replace the words “click” and “double-click”.

Main Features

Your unit has the following characteristics:

Two-slot platform

Multitasking possibilities

Touchscreen (LCD and touchscreen optimized for outdoor use available as an option)

USB 2.0 ports (host)

Ethernet port (10/100/1000 Base-T)

Fiber inspection probe port

Headset/microphone port (for any commercially available headset equipped with a microphone, and having a 2.5 mm connector)

Optional internal Wi-Fi and Bluetooth devices

Optional GPS USB key

Optional 3G USB modem key

VPN capability

Autonomy (8 hours)

Windows Embedded Standard operating system

Ruggedness (GR-196-CORE)

Introducing the FTB-200 v2 Compact Modular Platform

Main Features

Optional built-in power meter and VFL

Direct Web access from your unit

Possibility to take screen captures

PDF file generator and viewer available from your unit

Easy transfer of files and folders to a USB storage device

Easy updates for applications via Update Manager

Front panel

Introducing the FTB-200 v2 Compact Modular Platform

Main Features

Fiber inspection probe port

USB host ports

USB host port

RJ-45 port

Top panel

VFL Built-in power meter

Introducing the FTB-200 v2 Compact Modular Platform

LED Panel Description

Bottom panel

Retaining screws

LED Panel Description

The LED panel located on the front of the unit provides you with the status of your unit.

Note: The function of certain LEDs vary with the applications.

Introducing the FTB-200 v2 Compact Modular Platform

LED Panel Description

Introducing the FTB-200 v2 Compact Modular Platform

Keypad Description

Keypad Description

The keypad of your unit gives you access to various functions at all times. The table below shows an overview of their purpose.

Note: The function of certain buttons vary with the applications.

Introducing the FTB-200 v2 Compact Modular Platform

Ports

Ports

Your unit is equipped with several communication ports (for probe, mouse, keyboard, hub, etc.). It can also be equipped with internal Wi-Fi and Bluetooth devices for wireless information transfer. These two devices are optional.

There are two USB 2.0 host ports located on the left panel of the unit.

All the other ports are located on the right panel of the unit:

8-pin (mini-DIN) connector to connect the fiber inspection probe.

USB 2.0 host port (type A connector) to connect USB memory drives, keyboards, mouse devices, etc.

RJ-45 (10/100/1000 Base-T) port to connect your unit to an Ethernet network.

Headset/microphone port (for 2.5 mm connector).

Introducing the FTB-200 v2 Compact Modular Platform

Power Sources

Power Sources

The unit operates with the following power sources:

AC adapter/charger (connected to a standard power outlet–indoor use only).

Rechargeable Lithium-Ion battery (automatically takes over if you disconnect the AC adapter/charger).

Note: When it is connected with the AC adapter/charger, the unit will function even if the battery is not present.

CAUTION

EXFO guarantees the specifications and viability of the products ONLY if they are used with chargers and batteries provided by EXFO.

Possible to switch from AC adapter/charger to battery power or vice versa without affecting operation.

Automatic recharge when AC adapter/charger is connected.

Rechargeable battery (for clock). This battery can keep the date and time for weeks even if AC power and the Lithium-Ion battery (main battery) are not connected.

Optional Software Package

An optional software package (IPT package) is offered with the application. With this package, you can perform ping and trace route tests. For more information on how to activate software options, see Activating Software Options on page 37.

Introducing the FTB-200 v2 Compact Modular Platform

Conventions

Conventions

Before using the product described in this guide, you should understand the following conventions:

WARNING

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Do not proceed unless you understand and meet the required conditions.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. Do not proceed unless you understand and meet the required conditions.

CAUTION

Indicates a potentially hazardous situation which, if not avoided, may result in component damage. Do not proceed unless you understand and meet the required conditions.

IMPORTANT

Refers to information about this product you should not overlook.

2 Safety Information

WARNING

Do not install or terminate fibers while a light source is active. Never look directly into a live fiber and ensure that your eyes are protected at all times.

WARNING

The use of controls, adjustments and procedures, namely for operation and maintenance, other than those specified herein may result in hazardous radiation exposure or impair the protection provided by this unit.

IMPORTANT

documentation. Ensure that you understand and meet the required conditions before using your product.

IMPORTANT

Other safety instructions relevant for your product are located throughout this documentation, depending on the action to perform. Make sure to read them carefully when they apply to your situation.

Safety Information

Other Safety Symbols on Your Unit

Other Safety Symbols on Your Unit

One or more of the following symbols may also appear on your unit.

Safety Information

Laser Safety Information

Laser Safety Information

Units with Built-In VFL

Your instrument is a Class 3R laser product in compliance with standards IEC 60825-1: 2007 and 21 CFR 1040.10, except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007. Laser radiation is emitted at the output port. It is potentially harmful in direct intrabeam viewing.

The following label(s) indicate that the product contains a Class 3R source:

Affixed to back of unit (under the stand).

When the VFL laser is active, the LED on the front of the unit blinks, and the symbol is displayed in the power meter and VFL application.

Units without Built-In VFL

If your unit is not equipped with a VFL, the laser class of your unit depends on the modules that you use. Refer to the user guide or the online help of the different modules for the exact information.

Safety Information

Electrical Safety Information

Electrical Safety Information

If you need to ensure that the unit is completely turned off, disconnect the power cable and remove the battery.

WARNING

Use the external power supply indoors only.

Position the unit so that the air can circulate freely around it.

Operation of any electrical instrument around flammable gases or fumes constitutes a major safety hazard.

To avoid electrical shock, do not operate the unit if any part of the outer surface (covers, panels, etc.) is damaged.

Only authorized personnel should carry out adjustments, maintenance or repair of opened units under voltage. A person qualified in first aid must also be present. Do not replace any components while power cable and battery are connected.

Unless otherwise specified, all interfaces are intended for connection to Safety Extra Low Voltage (SELV) circuits only.

Capacitors inside the unit may be charged even if the unit has been disconnected from its electrical supply.

Safety Information

Electrical Safety Information

WARNING

Use only the listed and certified AC adapter/charger provided by EXFO with your unit. It provides reinforced insulation between primary and secondary, and is suitably rated for the country where the unit is sold.

Use only accessories (such as the car outlet adapter, batteries, and fiber inspection probe) designed for your unit and approved by EXFO. For a complete list of accessories available for your unit, refer to its technical specifications.

When you use the unit outdoors, ensure that it is protected from liquids, dust, direct sunlight, precipitation, and full wind pressure.

Safety Information

Electrical Safety Information

a.With FTB-8XXX modules, the maximum operation temperature is 40 °C (104 °F).

b.With FTB-8XXX modules, the maximum storage temperature is 50 °C (122 °F).

c.Measured in 0 °C to 31 °C (32 °F to 87.8 °F) range, decreasing linearly to 50 % at 40 °C (104 °F).

d.Equipment must be normally protected against exposure to direct sunlight, precipitation and full wind pressure.

e.Not exceeding ± 10 % of the nominal voltage.

Safety Information

Electrical Safety Information

IMPORTANT

The operation and storage temperatures of some modules may differ from the temperatures specified for your platform. In this case, always ensure that you comply with the most restrictive conditions (either module or platform).

Inserting and Removing Test Modules

CAUTION

Never insert or remove a module while the Compact Modular Platform is turned on. This will result in immediate and irreparable damage to both the module and unit.

CAUTION

To avoid damaging your unit, use it only with modules approved by EXFO.

WARNING

When the laser safety LED is flashing, at least one of your modules is emitting an optical signal. Please check all modules, as it might not be the one you are currently using.

Getting Started with Your Unit

Inserting and Removing Test Modules

To insert a module into the Compact Modular Platform:

1.Turn off your unit.

2.Position the unit so that its front panel is facing you.

Getting Started with Your Unit

Inserting and Removing Test Modules

3.Take the module and place it vertically so that the retaining screw hole is at the left of the connector pins.

CAUTION

Inserting a module upside down could result in permanent damage to the module, as the connector pins might be bent.

4.Insert the protruding edges of the module into the grooves of the unit’s module slot.

5.Push the module all the way to the bottom of the slot, until the retaining screw makes contact with the unit casing.

6.Place the unit so that its bottom panel is facing you.

Getting Started with Your Unit

Inserting and Removing Test Modules

7.While applying slight pressure to the module, lift the mobile part of the retaining screw and use it to turn the retaining screw clockwise until it is tightened.

This will secure the module into its “seated” position.

Turn retaining screws clockwise

Bottom panel

When you turn on the unit, the startup sequence will automatically detect the module.

Getting Started with Your Unit

Inserting and Removing Test Modules

To remove a module from the Compact Modular Platform:

1.Turn off your unit.

2.Position the unit so that the bottom panel is facing you.

3.Lift the mobile part of the retaining screw and use it to turn the retaining screw counterclockwise until it stops.

The module will be slowly released from the slot.

Turn retaining screws counterclockwise

Bottom panel

4. Place the unit so that the top panel is facing you.

Getting Started with Your Unit

Inserting and Removing Test Modules

5.Hold the module by its sides or by the handle (NOT by the connector) and pull it out.

CAUTION

Pulling out a module by a connector could seriously damage both the module and connector. Always pull out a module by its casing.

6. Cover empty slots with the supplied protective covers.

Getting Started with Your Unit

Using a Keyboard, Mouse or Other USB Devices

Using a Keyboard, Mouse or Other USB Devices

Your unit supports many USB devices. The table below lists the supported USB devices.

Getting Started with Your Unit

Using a Keyboard, Mouse or Other USB Devices

You can connect several devices at the same time.

IMPORTANT

Your unit does not support USB printers. If you want to print documents, you must use PDFCreator or a network printer (see Printing Documents on page 83), or transfer your files to a

computer (see Managing Data on page 115) that has access to a network printer.

To use a USB device with your unit:

Connect the USB device to any of the USB ports (located on the left or right side of the unit).

Note: It is not necessary to turn off the unit before connecting the USB device. The software will automatically detect its presence.

Your device is automatically recognized and immediately usable (provided that it uses the drivers already available on your unit).

Getting Started with Your Unit

Using the On-Screen (Virtual) Keyboard

Using the On-Screen (Virtual) Keyboard

Your unit is equipped with an on-screen keyboard that supports multilingual features. This keyboard functions according to the keyboard settings of Windows.

To use the on-screen keyboard:

1.From Compact Toolbox, tap the on-screen keyboard icon on the lower-right part of the screen (under the clock).

2.Select the location where you want to enter text.

3.Enter the data as required.

4.Exit the location when you have finished entering data.

Right-Clicking with the Touchscreen

If you are used to work with a mouse, you may find it useful to be able to perform a right-click on your touchscreen.

To right-click with the touchscreen:

From the location where you want to right-click, using the stylus or any blunt pointing device, press the screen for a few seconds until the shortcut menu appears.

If you want to hide the shortcut menu without performing any action, simply tap anywhere outside the menu.

Getting Started with Your Unit

Turning On or Off the Unit

Turning On or Off the Unit

There are several ways to turn off the unit, including the following:

Standby: keeps the unit’s status information in memory (RAM). The next time you turn your unit on, you will quickly return to your work environment (running applications will still be running). This mode will take more battery power while the unit is off.

Hibernation: saves the unit’s status information that was in memory (RAM) to a special file on the disk. The next time you turn your unit on, this file will be used to ensure that you return to your work environment (running applications will still be running). The unit will take longer to start up than in Standby mode, but it requires less battery power when the unit is off. You can configure your unit to switch automatically from Standby to Hibernation mode after the specified delay.

Shutdown: completely cuts power to the test modules and platform; the unit will perform a complete restart routine the next time you use it. You should perform a shutdown if you do not intend to use your unit for a week or more.

After a shutdown, the unit will start in Compact Toolbox or in the application you defined as the startup application.

Note: Should the unit ever stop responding, you can force a hardware reset by pressing and holding down the power button for more than 10 seconds.

By default, your unit will display the standard shutdown window from which you can select the desired shutdown mode. However, you can configure your unit to perform a different action when the power button is pressed.

You can also configure your unit to automatically restart when AC power comes back after the unit has turned off (emergency shutdown, standby, or hibernation modes) when battery level is too low.

Getting Started with Your Unit

Turning On or Off the Unit

To turn on the unit:

Press the On/Off button.

To turn off the unit:

1.Press the On/Off button. OR

On the Windows taskbar, tap Start.

This will display the standard shutdown window, from which you have a choice of actions or shutdown modes.

2.Select Shutdown.

To define the behavior of the power button:

1.From the Main Menu, tap Setup.

2.Double-tap Power Options.

3.Select the Advanced tab.

Getting Started with Your Unit

Turning On or Off the Unit

4.From the When I press the power button on my computer list, select the desired behavior (Ask me what to do option is selected by default).

5.Tap Apply to confirm the changes, and then OK to return to Control Panel.

Getting Started with Your Unit

Turning On or Off the Unit

To configure your unit to automatically restart after AC power comes back:

1.From the Main Menu, tap Setup.

2.Double-tap Application Startup.

3.Select the Power on the unit when AC outlet is connected or after power outage box to enable the corresponding option.

OR

Clear the box if you prefer that your unit does not restart automatically after AC power comes back.

4.Tap OK to confirm the changes and return to the Control Panel window.

Getting Started with Your Unit

Installing or Upgrading the Applications

Installing or Upgrading the Applications

All the necessary applications have been preinstalled and configured at the factory. However, you may have to upgrade some applications when new versions become available or to reinstall them.

Note: Only administrator-level users can install software under Windows Embedded Standard.

From the DVD that came with your unit, you can create an installation USB key in case you ever need to reinstall Compact ToolBox (the software that comes with your platform) and the module applications as well as Update Manager. All the necessary files will be copied to the USB key.

Each time you purchase a new module, you will also receive a DVD with which you could create a new installation USB key. It could be a good idea to verify that the most recent Update Manager application is installed on your unit.

When updates are available for an application, you will need to download them from Internet, either directly on your unit or on a computer. In the latter case, you will need to transfer the update files to your unit

(see Managing Data on page 115). The update files must be copied to the location that has been specified for the deployment packages in Update Manager.

Getting Started with Your Unit

Installing or Upgrading the Applications

IMPORTANT

If you ever need to reinstall Update Manager on your unit, ensure that:

The installation files for Update Manager remain on your unit. Otherwise, it will not be possible to install new versions of this application later.

You choose the folder containing the Update Manager installation files carefully. If you move or rename this folder, you will have to manually browse for the modified folder when you want to install new versions of this application.

For the creation of an installation USB key, you will need:

the installation DVD

a computer equipped with a USB port; Windows must be installed on the computer

a USB memory key

For the upgrades, you will need:

an FTB-200 v2 Compact Modular Platform unit

a computer equipped with a USB port; Windows must be installed on the computer

a USB memory key

Note: For the upgrades, the computer and USB key are only necessary if you do not wish to download the files directly on your unit.

Note: For more information on the installation, refer to the Update Manager online help.

Getting Started with Your Unit

Installing or Upgrading the Applications

To update or reinstall Update Manager:

1.If necessary, retrieve the desired installation files from the Internet.

If you do not intend to download files directly on your unit, connect a USB memory key to one of the USB ports of the computer and copy the installation files to this USB key.

2.If it is not already done, turn on your unit.

3.Exit Compact Toolbox and the modules’ applications.

4.If you want to install Update Manager using the USB key, disconnect it from the computer and connect it to one of the USB ports of your unit.

5.On your unit, create a folder on the Windows desktop.

6.Copy the installation files (from the USB key) to the newly created folder.

7.From the newly created folder, tap the Setup.exe file to start the installation.

8.Follow the on-screen instructions.

9.When the installation is complete, simply disconnect the USB memory key.

Getting Started with Your Unit

Installing or Upgrading the Applications

To install or upgrade the applications:

1.If necessary, retrieve the desired installation files from the Internet.

If you do not intend to download files directly on your unit, connect a USB memory key to one of the USB ports of the computer and copy the installation files to this USB key.

2.If it is not already done, turn on your unit. If necessary, exit the modules’ applications.

3.If you want to install or update applications using the USB key, disconnect it from the computer and connect it to one of the USB ports of your unit.

4.Copy the installation files (from the USB key) to the folder containing the update and installation packages on your unit. By default, Update Manager will search for files at the root of the USB key. For more information, refer to the Update Manager online help.

5.From Compact ToolBox, on your unit, select the Utilities tab.

6.Double-tap Update Manager to start the corresponding application. For more information on how to install or upgrade applications, refer to the Update Manager online help.

7.When installation is complete, simply disconnect the USB memory key.

Getting Started with Your Unit

Installing or Upgrading the Applications

To create an installation USB key:

1.Turn on the computer and insert the installation DVD in the CD/DVD drive.

2.Connect a USB memory key to one of the USB ports of the computer.

3.From the Welcome window on the installation DVD, click Compact Toolbox and Tools.

4.Select the Compact Toolbox check box and click Next.

5.Follow the on-screen instructions. All the necessary components will be copied to your USB key.

6.When the operation is complete, click Close, and then Exit to close the installation DVD window.

7.Disconnect the USB memory key from the computer.

Your new installation USB key is now ready.

Getting Started with Your Unit

Activating Software Options

Activating Software Options

The software options purchased at the same time as your unit have been activated for you already. However, if you purchase options afterwards, you will have to activate them yourself.

IMPORTANT

If you want to activate software options for modules of the FTB-81xx Series or the FTB-85xx Series, refer to the user guide of your product for the specific activation instructions.

In all other cases, you can follow the instructions presented in this section.

Before being able to activate options, you need to contact EXFO with the following information:

Purchase order number of the newly purchased options

Module or platform serial number (depending on whether the software options were purchased for a module or the platform)

Customer’s name

Customer’s company name

Customer’s phone number

Customer’s e-mail address

Module or platform on which the option will be installed

You will receive a single key (.key) file with which you will be able to unlock all the new options that you have purchased.

Getting Started with Your Unit

Activating Software Options

To activate the options for your unit:

1.Connect a USB memory key to one of the USB ports of your computer.

2.Copy the key file to the USB memory key.

3.Disconnect the USB key from the computer and connect it to your unit.

4.From Compact ToolBox, select the Utilities tab, then double-tap

Options Activation.

Getting Started with Your Unit

Activating Software Options

5.In the Platform Options tab, use the Browse button to locate the key file that you want to use.

6.Press Activate.

The option indicator will turn into a green check mark to confirm that the option is now active.

7.Close to exit

Note: At this point, if you have used a USB key to copy your key file, you can remove it as it is not required to use your new options.

Getting Started with Your Unit

Activating Software Options

To activate software options for your module:

1.Connect a USB memory key to one of the USB ports of your computer.

2.Copy the key file to the USB memory key.

3.Disconnect the USB key from the computer and connect it to your unit.

4.From Compact ToolBox, select the Utilities tab, then double-tap

Options Activation.

Manual abstract: user guide EXFO FTB-200

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner’s manual, quick start guide, technical datasheets…
In any way can’t Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on «Download the user manual» at the end of this Contract if you accept its terms, the downloading of the manual EXFO FTB-200 will begin.