-
Page 1
Industrial Controls Monitoring and Control Devices 3UG4 / 3RR2 Monitoring Relays Gerätehandbuch Manual Edition 05/2016 siemens.com… -
Page 3
___________________ 3UG4 / 3RR2 monitoring relays Introduction ___________________ Safety information Industrial Controls System overview 3RR2 current monitoring relays Monitoring and control devices 3UG4 / 3RR2 monitoring relays 3UG4501 filling level monitoring relay ___________________ 3UG4.1 line monitoring relay Manual ___________________ 3UG4621/3UG4622 current… -
Page 4
Note the following: WARNING Siemens products may only be used for the applications described in the catalog and in the relevant technical documentation. If products and components from other manufacturers are used, these must be recommended or approved by Siemens. Proper transport, storage, installation, assembly, commissioning, operation and maintenance are required to ensure that the products operate safely and without any problems. -
Page 5: Table Of Contents
Table of contents Introduction……………………..11 Service&Support ………………….. 11 Technical data in Siemens Industry Online Support …………14 DataMatrix code …………………… 15 Safety information ……………………17 Standards…………………….. 17 Product-specific safety information ………………18 Approvals, test certificates, characteristics …………….. 18 System overview ……………………. 19 Product description ………………….
-
Page 6
Functions ………………………91 Operation ………………………94 Diagnostics ……………………94 5.5.1 Diagnostics with LED ………………….94 Circuit diagrams …………………….95 Technical data ……………………96 3UG4.1 line monitoring relay ………………….. 101 Application areas ………………….102 3UG4511 line monitoring relay ………………103 6.2.1 Operator controls and connection terminals …………..103 6.2.2 Function ………………………104 6.2.3… -
Page 7
Technical data ……………………. 184 3UG4625 residual current monitoring relay with 3UL23 transformer ……….191 Application areas ………………….191 Operator controls and connection terminals …………..192 Functions ……………………193 Operation ……………………202 Diagnostics ……………………203 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 8
Functions …………………….273 10.3 3UG4633 voltage monitoring relay ………………275 10.3.1 Operator controls and connection terminals …………..275 10.3.2 Functions …………………….276 10.4 Operation …………………….278 10.5 Diagnostics ……………………279 10.5.1 Indications on the display ………………..279 10.5.2 Reset ……………………..280 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 9
Accessories for 3RR2 current monitoring relays …………… 323 13.1.1 Sealable cover …………………… 323 13.1.2 Terminal support for stand-alone assembly…………..324 13.2 Accessories for 3UG4 monitoring relays …………….327 13.2.1 Sealable cover …………………… 327 13.2.2 Push-in lugs ……………………328 13.2.3 Probes for the 3UG4501 monitoring relay ……………. 329 13.2.4… -
Page 10
Dimension Drawings ……………………375 Dimension drawings 3RR2 monitoring relay…………..375 Dimension drawings 3UG4 monitoring relays …………..383 C.2.1 Dimension drawings 3UG4 monitoring relays. (2 connecting terminals) ……383 C.2.2 Dimension drawings 3UG4 monitoring relays. (3 connecting terminals) ……384 C.2.3 Dimension drawings 3UG4 monitoring relays. (4 connecting terminals) ……385 C.2.4… -
Page 11: Introduction
Introduction Purpose of the manual This manual describes the 3UG4 monitoring relays for stand-alone assembly and the 3RR2 current monitoring relays for mounting on 3RT2 contactors The manual provides overview information for integrating the monitoring relays into the system environment, and it describes the hardware and software components of the devices.
-
Page 12
Are you looking for product information such as technical data, updates or FAQs? Here, the «Product Support» section of the Service & Support Portal offers an extensive collection of all information about the Siemens Industry Automation and Drive Technologies products and solutions: ●… -
Page 13
Link: MyDocumentationManager (http://support.automation.siemens.com/WW/view/en/38715968) Reference You can find further information on structure and navigation in Online Support here (http://support.automation.siemens.com/WW/view/en/11774658). 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 14: Technical Data In Siemens Industry Online Support
Technical data in Siemens Industry Online Support Technical data sheet You can find all the technical data of the product in the Siemens Industry Online Support (https://support.industry.siemens.com/cs/ww/en/ps/16364/td). 1. Enter the full article number of the desired device in the «Product» field, and confirm with the Enter key.
-
Page 15: Datamatrix Code
Introduction 1.3 DataMatrix code DataMatrix code A DataMatrix code is lasered onto all 3UG4/3RR2 monitoring relay devices underneath the label. The DataMatrix codes are standardized in ISO/IEC 16022. The DataMatrix codes on Siemens devices use ECC200 coding for powerful error correction.
-
Page 16
SIEMENS Service&Support Portal, such as operating instructions, manuals, data sheets, FAQs, etc. We provide the SIEMENS Industry Support app free for this purpose and it can be used on most commercially available smartphones and tablets. -
Page 17: Safety Information
SIRIUS components have been approved by a whole range of bodies for various sectors (shipbuilding, etc.). An up-to-date list of approvals appears in Chapter 10 of the Catalog IC 10 — SIRIUS «Industrial Controls» (www.siemens.com/industrial-controls/catalogs), and more information, as well as an option to download certificates, can be obtained on the Internet (www.siemens.com/automation/csi_en).
-
Page 18: Product-Specific Safety Information
The devices may only be used for the applications described in the catalog and the technical description, and only in conjunction with equipment or components from other manufacturers which have been approved or recommended by Siemens. This product can function correctly and reliably only if it is transported, stored, assembled, and installed correctly, and operated and maintained as recommended.
-
Page 19: System Overview
This avoids unnecessary alarming and shutdowns while enhancing plant availability. The individual 3UG4 monitoring relays offer the following functions in various combinations: ● Undershoot and/or overshoot of liquid levels ● Phase sequence ●…
-
Page 20: Application Planning
(shipbuilding, etc.). An up-to-date list of approvals is provided in Chapter 10 of the Catalog IC 10 — SIRIUS «Industrial Controls.» You will find more information and an option to download certificates on the Internet (www.siemens.com/automation/csi_en). 3UG4 / 3RR2 monitoring relays…
-
Page 21: Connection Methods
2 x (0.5 to 2.5) mm² Finely stranded without end sleeve Finely stranded with end sleeve 1 x (0.5 to 2.5) mm² 2 x (0.5 to 1.5) mm² 2 x (20 to 14) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 22
1 x 10 mm² 2 x (20 to 14) 2 x (16 to 12) 2 x (18 to 2) 1 x 12 2 x (14 to 1 x (18 to 1) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 23: Spring-Loaded Connection
This could involve attaching end sleeves or pin cable lugs to the ends of the conductors; the tidiest solution is to use conductors whose ends have been sealed by means of ultrasound. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 24
A standardized screwdriver (3 mm slot; 3RA2908-1A) is offered in the Catalog IC10 «Industrial Controls» (www.siemens.com/industrial-controls/catalogs) as an actuation tool for opening the spring-loaded terminals. 3UG4 / 3RR2 monitoring relays… -
Page 25
If you insert the screwdriver into the central opening (main circuit S00 and S0 only) on the spring-loaded terminal, this could damage the terminal. Do not insert the screwdriver into the central opening on the spring-loaded terminal. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 26
System overview 3.3 Connection methods Spring-loaded terminal for 3UG4 monitoring relay Table 3- 4 Connecting the monitoring relay spring-loaded terminal Step Operating instruction Figure Insert the screwdriver into the topmost (A) or bottommost (B) operating slot on the right-hand side. -
Page 27
1 x (1 to 6) mm² Finely stranded with end sleeve 1 x (0.5 to 2.5) mm² 1 x (1 to 6) mm² 1 x (20 to 12) 1 x (18 to 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 28: Device Replacement By Means Of Removable Terminals
Hazardous Voltage Will cause death or serious injury. Turn off and lock out power before working on this equipment. The removable terminals of 3UG4 monitoring relays facilitate device replacement when necessary. The mechanical coding on the terminals prevents mix-ups. Note…
-
Page 29: Mounting / Removal
The following minimum clearances from grounded and live parts must be complied with when installing the 3RR2 monitoring relay: ● At the side: 6 mm ● Forward (on front): 6 mm Mounting position It can be mounted in any position. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 30
(tightening torque 0.8 … 1.2 Nm). Check that the cable is clamped tight. Note The connection cross-sections of the removable and permanently connected terminal blocks with screw-type connections are described in the Chapter «Screw-type connection (Page 21)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 31
For direct mounting on a 3RF34 solid-state contactor, an additional 3RF3900-0QA88 adapter is required, which is attached to the solid-state contactor. Information is provided in the «SIRIUS solid state contactors / solid state reversing contactors» (http://support.automation.siemens.com/WW/view/en/44362244) operating instructions. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 32
Position the screwdriver on the current monitoring relay as shown in the figure. Carefully dislodge the current monitoring relay from the contactor. Pull the current monitoring relay toward you and away from the contactor. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 33
Swing the contactor upwards to remove it Separately mounted Note The accessories required for separate mounting are described in the Chapter «Terminal support for stand-alone assembly (Page 324)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 34: Mounting The 3Ug4 Monitoring Relay
Standard-rail mounting The illustration below shows how to mount the 3UG4 monitoring relay onto a standard rail. Table 3- 13 Mounting the monitoring relay (mounting on and removing from standard rail)
-
Page 35: Installing The 3Ug458. Monitoring Relay
1 / 2 To remove, apply the screwdriver to the device and push it up with a twisting motion against the tension of the fixing spring. Swing the device upwards to remove it. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 36: Overview Of The Functions
✓ Supply voltage Self-powered, without auxiliary voltage — — Externally powered, with auxiliary voltage ✓ ✓ ✓: Function available 2p: Monitoring is 2-phase 3p: Monitoring is 3-phase — : Function not available 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 37: 3Ug45 / 3Ug46 Monitoring Relays
— — overshoot / resistance overshoot Monitoring for filling level ✓ — — — — — — — — — — — — — — — — — undershoot / resistance undershoot 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 38
The required line quality can be ensured by using line filters/sine-wave filters where applicable. Of course, the suitability of the relevant monitoring relay for the monitored line frequencies must also be considered. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 39: Menu-Based Operation
2.5 s, in a further step, the basic device parameters , such as the switching behavior of the output relays, the reset response in the event of a fault, and/or the tripping delay times can be set. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 40
If a threshold is overshot or undershot, the outputs of the monitoring relays switch over after the set delay time. The display indicates the type of error. Error detected Error1 /Error2 / … • ④ Settings for basic device parameters, see below 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 41
An arrow symbol indicates whether the measuring value is within, above or below the set thresholds. ③ Next to this, one or two symbols represent the type (changeover contact or semiconductor output) and the switching status of the outputs. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 42
You can switch menus from any of the menu commands. While the SET key pressed, appears on the display. After a successful change, you arrive at current measuring value (measuringvalue1) or the current error of the RUN menu level. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 43
30 seconds after the last limit value change. Note Quitting the SET menu level will trigger an internal reset in 3UG4621/3UG4622/3UG4625 and 3UG4641 device variants and restart the startup delay. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 44
System overview 3.6 Menu-based operation 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 45: 3Rr2 Current Monitoring Relays
Apparent current monitoring and active current monitoring are described in more detail in the Chapter «Parameters (Page 363)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 46
The accessories have been tailored to the current monitoring relays; they can be mounted easily and without the need for tools. The accessories are described in the Chapter «Accessories for 3RR2 current monitoring relays (Page 323)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 47: Application Areas
Surface grinding machine • Breaking mill • Milling machine • Car wash • Lifting platform • Screw conveyor • Crane • Turning machine • Woodworking • Grain mills • Steel industry • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 48: Performance Features Of Current Monitoring Relays
-.FW30: 24 to 240 V AC/DC • Monitoring for current 3-phase 3-phase 3-phase overshoots and/or undershoots Contacts 1 CO contact/ 1 CO contact/ 1 CO contact/ 1 semiconductor output 1 semiconductor output 1 semiconductor output 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 49: General Data
Just 1 option per size with a wide setting range makes • configuration easy. You can find further technical information on 3RR24 in the Manual «3UG48/3RR24 monitoring relays for IO-Link (http://support.automation.siemens.com/WW/view/en/54375430)» on the internet. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 50: Properties
1 CO contact 1 CO contact Allow the system or process to be shut down in • the event of an irregularity 1 semiconductor output Can be used to output signals • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 51: Configuration Of Load Feeders
Spring-loaded connection system for ✓ ✓ Enables fast connections • main circuit (option) and auxiliary Ensures that connections are vibration- • circuit (option) resistant Enables maintenance-free connections • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 52: Combinations With 3Rt20 Contactor
3RR2243 8.0 to 80 A ✓ X = with stand-alone assembly support You can find further technical information on 3RR24 in the Manual «3UG48/3RR24 monitoring relays for IO-Link (http://support.automation.siemens.com/WW/view/en/54375430)» on the internet. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 53: 3Rr21 Current Monitoring Relays
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 59)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 54: Function
If the unmonitored phase 5/L3 — 6/T3 fails, this can be detected if a motor is connected by an increase in current in both phases 1/L1 — 2/T1 and 3/L2 — 4/T2. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 55
3RR2 current monitoring relays 4.4 3RR21 current monitoring relays Function diagrams Memory = O: Memory = I: I▲ I▼ = Off I▲ = Off I▼ I▲ I▼ 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 56: Operation
The position digits refer to the front view in the Chapter «Operator controls and connection terminals (Page 53).» Hysteresis The hysteresis is set to a fixed value of 6.25% of the set threshold. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 57
• Phase failure The parameters are described in the Chapter «Parameters (Page 363)». Required tools The same screwdriver can be used to set the parameters as for mounting the current monitoring relays. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 58: Diagnostics
Voltage is not applied at B1 — B2 READY on Voltage is applied at B1 — B2 You can find more information about the LED display response in the Chapter «Function (Page 54).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 59: Circuit Diagrams
4.4 3RR21 current monitoring relays 4.4.5 Circuit diagrams Internal circuit diagrams 3RR21 3RR2141-1A.30 current monitoring relay Image 4-2 1 CO contact, 2-phase 3RR2141-2A.30, 3RR2142-.A.30, 3RR2143-.A.30 current monitoring relays Image 4-3 1 CO contact, 2-phase 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 60: Technical Data
15g / 11 ms 10g / 11 ms Resistance against vibration 10 … 55 Hz / 0.35 mm Impulse voltage resistance rated value Operating apparent output rated V·A value Rating Rated value 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 61
• active current monitoring • undercurrent recognition of • 3 phases phase sequence recognition • can be activated or • deactivated phase sequence recognition self-reset • reset external • manual RESET • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 62
• maximum permissible 1 600 for overcurrent duration • < 1 s maximum permissible Class 10 = 80 A Class 20 = 60 A Class 30 = 50 A 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 63
2x (20 … 14) 2x (24 … 16) for AWG conductors for auxiliary • contacts Tightening torque N·m 0.8 … 1.2 with screw-type terminals • Verification of suitability CE / UL / CSA 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 64
2x (20 … 14) 2x (24 … 16) for AWG conductors for auxiliary • contacts Tightening torque N·m 0.8 … 1.2 with screw-type terminals • Verification of suitability CE / UL / CSA 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 65
2x (20 … 14) 2x (24 … 16) for AWG conductors for auxiliary • contacts Tightening torque N·m with screw-type terminals • Verification of suitability CE / UL / CSA 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 66
Distance, to be maintained, to earthed part forwards • backwards • upwards • downwards • sidewards • Distance, to be maintained, conductive elements forwards • backwards • upwards • downwards • sidewards • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 67
Distance, to be maintained, to earthed part forwards • backwards • upwards • downwards • sidewards • Distance, to be maintained, conductive elements forwards • backwards • upwards • downwards • sidewards • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 68
AC-15 • – at 24 V – at 230 V – at 400 V at DC-13 at 24 V • at DC-13 at 125 V • at DC-13 at 250 V • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 69
III according to IEC 60664 with degree of pollution 3 rated value Impulse voltage resistance of the auxiliary and control 4 000 current circuit rated value Stored energy time supply voltage failure minimum 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 70: 3Rr22 Current Monitoring Relays
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 78)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 71: Function
You can find a description of the individual parameters in the Chapter «Parameters (Page 363)». You will find the switching states of the output relay below in the Section «Function diagrams» and in the Chapter «Diagnostics (Page 77).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 72
When a defined current flow returns to all branch circuits (1/L1 — 2/T1, 3/L2 — 4/T2 und 5/L3 — ② 6/T3) (time ), the CO contact and the semiconductor output respond again according to the defined settings. If manual RESET (Mem = yes) is selected, the tripping state is saved. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 73
Relay switching behavior = NC (closed-circuit Relay switching behavior = NO (open-circuit principle) principle) I▲ / I!▲ I▼ / I!▼ = Off n x I▲ I▲ / I!▲ = Off I▼ / I!▼ I >> = yes 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 74
4.5 3RR22 current monitoring relays Display Memory = no Memory = no Relay switching behavior = NC (closed-circuit Relay switching behavior = NO (open-circuit principle) principle) I▲ / I!▲ = Off I▼ / I!▼ = yes 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 75: Operation
1 min. 0 min. «SET» Blocking current monitoring (n x I▲) no x I▲ 5 x I▲ 1 x I▲ no x I▲ «SET» Residual current monitoring no or yes (I >> 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 76
• Incorrect phase sequence (if activated) • Phase failure The up-to-date measured value is displayed permanently. The parameters are described in the Chapter «Parameters (Page 363)». Menu-based operation is described in the Chapter «Menu-based operation (Page 39)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 77: Diagnostics
Flashing: Delay time (ON-delay or tripping delay) running • Masked out: Semiconductor output open, supply voltage not • switched through You will find more information about the switching behavior of the output relays in Chapter «Function (Page 71)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 78: Circuit Diagrams
4.5 3RR22 current monitoring relays 4.5.5 Circuit diagrams Internal circuit diagrams 3RR22 3RR2241-1F.30 current monitoring relay Image 4-5 1 CO contact, 3-phase 3RR2241-2F.30, 3RR2242-.F.30, 3RR2243-.F.30 current monitoring relays Image 4-6 1 CO contact, 3-phase 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 79: Technical Data
Operating apparent output V·A rated value Rating Rated value Reference code according to DIN 40719 • extended according to IEC 204-2 according to IEC 750 according to DIN EN • 61346-2 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 80
• undercurrent recognition • of 3 phases phase sequence • recognition can be activated or • deactivated phase sequence recognition self-reset • reset external • manual RESET • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 81
• maximum permissible 1 600 for overcurrent duration • < 1 s maximum permissible Class 10 = 80 A Class 20 = 60 A Class 30 = 50 A 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 82
2x (20 … 14) 2x (24 … 16) for AWG conductors for auxiliary • contacts Tightening torque N·m 0.8 … 1.2 with screw-type terminals • Verification of suitability CE / UL / CSA 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 83
2x (20 … 14) 2x (24 … 16) for AWG conductors for auxiliary contacts • Tightening torque N·m 0.8 … 1.2 with screw-type terminals • Verification of suitability CE / UL / CSA 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 84
2x (20 … 14) 2x (24 … 16) for AWG conductors for auxiliary contacts • Tightening torque N·m with screw-type terminals • Verification of suitability CE / UL / CSA 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 85
Distance, to be maintained, to earthed part forwards • backwards • upwards • downwards • sidewards • Distance, to be maintained, conductive elements forwards • backwards • upwards • downwards • sidewards • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 86
Distance, to be maintained, to earthed part forwards • backwards • upwards • downwards • sidewards • Distance, to be maintained, conductive elements forwards • backwards • upwards • downwards • sidewards • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 87
AC-15 • – at 24 V – at 230 V – at 400 V at DC-13 at 24 V • at DC-13 at 125 V • at DC-13 at 250 V • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 88
III according to IEC 60664 with degree of pollution 3 rated value Impulse voltage resistance of the auxiliary and 4 000 control current circuit rated value Stored energy time supply voltage failure minimum 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 89: 3Ug4501 Filling Level Monitoring Relay
Filling level monitoring of oil sumps • Overflow protection • Filling level monitoring of rainwater catchment basins • Dry-run protection • Water supply • Leakage monitoring • Waste water treatment plant • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 90: Operator Controls And Connection Terminals
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 95)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 91: Functions
Tripping can be delayed by 0.5 to 10 s to avoid tripping the switching function too early when the level has not quite been reached (e.g. wave motion or foaming of the liquid). The switching states of the output relay are given below in the section entitled «Function diagrams.» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 92
If the rated control supply voltage is switched on again after > 0.5 s + Delay ( t ) (device reset), the output relay switches depending on the set relay switching behavior. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 93
Inflow control (UN ), two-point closed-loop control control OV = overshoot UN = undershoot Drainage control (OV ), one-point closed-loop Inflow control (UN ), one-point closed-loop control control OV = overshoot UN = undershoot 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 94: Operation
(contact 11-12 open, contact 11-14 closed), the yellow LED next to the contact symbol on the device cover lights up. The switching behavior of the output relay is shown in Chapter «Functions (Page 91).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 95: Circuit Diagrams
3UG4501 filling level monitoring relay 5.6 Circuit diagrams Circuit diagrams Internal circuit diagram 3UG4501-.A.30 level monitoring relays Wiring examples Drainage control One-point closed-loop control Two-step control Inflow control Two-step control One-point closed-loop control 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 96: Technical Data
0.85 … 1.1 – for AC at 60 Hz • 0.85 … 1.1 – for AC 0.85 … 1.1 for DC • Impulse voltage resistance rated value Recorded real power Protection class IP IP20 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 97
V·A — at 240 V for AC maximum • Ambient temperature °C -25 … +60 during operating • °C -40 … +80 during storage • °C -40 … +80 during transport • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 98
Mechanical operating cycles as operating 10 000 000 time typical Electrical operating cycles as operating time 100 000 at AC-15 at 230 V typical Operating cycles with 3RT2 contactor 5 000 maximum 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 99
• Distance, to be maintained, conductive elements forwards • backwards • sidewards • upwards • downwards • Mounting type screw and snap-on mounting Product function removable terminal for auxiliary and control circuit 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 100
• Adjustable response value impedance kΩ 2 … 200 Measuring electrode current maximum Measuring electrode voltage maximum Number of measuring circuits Stored energy time at mains power cut minimum 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 101: 3Ug4.1 Line Monitoring Relay
Depending on the version, the electronic line monitoring relays monitor the following: ● Phase sequence ● Phase failure with and without neutral conductor monitoring ● Phase asymmetry ● Undervoltage and/or overvoltage 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 102: Application Areas
• monitoring of the generator) Overvoltage System protection against destruction caused by supply overvoltages • Energy supply to the line • Lamps (UV lamps, laser lamps, OP lighting, tunnels, traffic lights) • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 103: 3Ug4511 Line Monitoring Relay
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 106)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 104: Function
Chapter «Diagnostics (Page 105).» Reset response The device features an autoreset that resets the output relay to its original state after an error message and rectification of the fault that has occurred. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 105: Diagnostics
State of the output relay 12/ 11/ 14 22/ 21/ 24 Correct phase sequence Incorrect phase sequence You will find more information about the switching behavior of the output relays in Chapter «Function (Page 104).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 106: Circuit Diagrams
It is not necessary to fuse the measuring circuit to protect the device. Fusing for line protection depends on the cross-section used. Note The 3UG4511 line monitoring relays are only suitable for line frequencies of 50 / 60 Hz! 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 107: Technical Data
320 … 500 420 … 690 at 60 Hz at AC rated value • Operating range factor control supply voltage rated value at 50 Hz for AC • at 60 Hz for AC • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 108
IEC 60664 with degree of pollution 3 rated value Degree of pollution Ambient temperature °C -25 … +60 during operating • °C -40 … +85 during storage • °C -40 … +85 during transport • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 109
Distance, to be maintained, to earthed part forwards • backwards • sidewards • upwards • downwards • Distance, to be maintained, to the ranks assembly forwards • backwards • sidewards • upwards • downwards • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 110
2x (24 … 16) – solid 2x (20 … 14) 2x (24 … 16) – stranded Tightening torque N·m 0.8 … 1.2 — with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 111: 3Ug4512 Line Monitoring Relay
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 115)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 112: Function
LED lights up red continuously and the output relays drop out to protect the application from any damage that may result. You will find the switching states of the output relays below in section «Function diagrams» and in Chapter «Diagnostics (Page 114).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 113
The red «phase failure / phase sequence» LED is a fault diagnostics display and does not indicate the current state of the relay! Function diagrams 3UG4512 Phase failure Incorrect phase sequence ① ① ② ② Phase failure Phase sequence 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 114: Diagnostics
Supply voltage present • Incorrect phase sequence • Supply voltage present • Phase failure • You will find more information about the switching behavior of the output relays in Chapter «Function (Page 112)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 115: Circuit Diagrams
It is not necessary to fuse the measuring circuit to protect the device. Fusing for line protection depends on the cross-section used. Note The 3UG4512 line monitoring relays are only suitable for line frequencies of 50 / 60 Hz! 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 116: Technical Data
— reset external • self-reset • open-circuit or closed-circuit current principle • Starting time after the control supply voltage has been applied Response time maximum 0.45 Temperature drift per °C %/°C — 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 117
Field-bound parasitic coupling according to 10 V/m IEC 61000-4-3 Thermal current of the contact-affected switching element maximum Insulation voltage for overvoltage category III according to IEC 60664 with degree of pollution 3 rated value 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 118
Mechanical operating cycles as operating time 10 000 000 typical Electrical operating cycles as operating time at 100 000 AC-15 at 230 V typical Operating cycles with 3RT2 contactor maximum 5 000 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 119
• Distance, to be maintained, conductive elements forwards • backwards • sidewards • upwards • downwards • Type of mounting snap-on mounting Product function removable terminal for auxiliary and control circuit 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 120
2x (24 … 16) – solid 2x (20 … 14) 2x (24 … 16) – stranded Tightening torque N·m 0.8 … 1.2 — … with screw-type • terminals Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 121: 3Ug4513 Line Monitoring Relay
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 126)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 122: Function
160 to 690 V AC and reverse power of up to 80 % from the load in the case of regenerative power recovery. You will find the switching states of the output relays below in section «Function diagrams» and in Chapter «Diagnostics (Page 125).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 123
Phase failure and undervoltage Incorrect phase sequence ① ① LED phase failure / phase sequence: Red LED phase failure / phase sequence: Red ② ② Phase failure Phase sequence ③ Tripping delay time ④ Hysteresis 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 124: Operation
(Page 121).» absolute threshold The parameters are described in Chapter «Parameters (Page 363).» Required tools The same screwdriver can be used to set the parameters as for mounting the line monitoring relays. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 125: Diagnostics
Supply voltage present • Phase failure • Supply voltage present • Line-to-line voltage • undershot You will find more information about the switching behavior of the output relays in Chapter «Function (Page 122).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 126: Circuit Diagrams
It is not necessary to fuse the measuring circuit to protect the device. Fusing for line protection depends on the cross-section used. Note The 3UG4513 line monitoring relays are only suitable for line frequencies of 50 / 60 Hz! 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 127: Technical Data
• self-reset • open-circuit or closed-circuit current principle • Starting time after the control supply voltage has been applied Response time maximum 0.45 Relative adjustment accuracy — Relative repeat accuracy 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 128
1 kV conductor SURGE according to IEC 61000-4-5 Electrostatic discharge according to IEC 61000-4-2 6 kV contact discharge / 8 kV air discharge Field-bound parasitic coupling according to IEC 10 V/m 61000-4-3 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 129
Mechanical operating cycles as operating time 10 000 000 typical Electrical operating cycles as operating time at 100 000 AC-15 at 230 V typical Operating cycles with 3RT2 contactor maximum 5 000 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 130
2x (24 … 16) – solid 2x (20 … 14) 2x (24 … 16) – stranded Tightening torque N·m 0.8 … 1.2 — … with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 131: 3Ug4614 Line Monitoring Relay
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 137)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 132: Functions
You will find the setting ranges and factory settings of the available parameters in Chapter «Operation (Page 135).» You will find a description of the individual parameters in Chapter «Parameters (Page 363).» Note The specified voltages represent the absolute thresholds. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 133
On the display, the current measuring value and the symbol for undershoot or overshoot flash. You will find the switching states of the output relays below in section «Function diagrams» and in Chapter «Diagnostics (Page 136).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 134
3UG4.1 line monitoring relay 6.5 3UG4614 line monitoring relay Function diagrams 3UG4614 Display Memory = no Memory = no Relay switching behavior = NC Relay switching behavior = NO (closed-circuit principle) (open-circuit principle) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 135: Operation
Phase sequence monitoring «SET» Relay switching behavior (closed- circuit principle NC / open-circuit principle NO) The parameters are described in Chapter «Parameters (Page 363).» Menu-based operation is described in Chapter «Menu-based operation (Page 39).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 136: Diagnostics
Flashing: Delay time (ON-delay or tripping delay) running • Masked out: Relay contact 21/22 closed, relay contact 21/24 open • You will find more information about the switching behavior of the output relays in Chapter «Functions (Page 132)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 137: Reset
Internal circuit diagrams 3UG4614 line monitoring relay Image 6-1 3UG4614 Note It is not necessary to fuse the measuring circuit to protect the device. Fusing for line protection depends on the cross-section used. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 138: Technical Data
• Starting time after the control supply voltage has been applied Response time maximum Precision of digital display +/-1 Digit Relative metering precision Relative adjustment accuracy Relative repeat accuracy 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 139
Field-bound parasitic coupling according to IEC 10 V/m 61000-4-3 Thermal current of the contact-affected switching element maximum Insulation voltage for overvoltage category III according to IEC 60664 with degree of pollution 3 rated value 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 140
Mechanical operating cycles as operating time 10 000 000 typical Electrical operating cycles as operating time at 100 000 AC-15 at 230 V typical Operating cycles with 3RT2 contactor maximum 5 000 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 141
2x (24 … 16) – solid 2x (20 … 14) 2x (24 … 16) – stranded Tightening torque N·m 0.8 … 1.2 — … with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 142: 3Ug4615 / 3Ug4616 Line Monitoring Relays
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 150)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 143: Functions
You will find the setting ranges and factory settings of the available parameters in Chapter «Operation (Page 146).» You will find a description of the individual parameters in Chapter «Parameters (Page 363).» Note The specified voltages represent the absolute thresholds. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 144
The 3UG4615 and 3UG4616 line monitoring relays are only suitable for line frequencies of 50 / 60 Hz! You will find the switching states of the output relays below in section «Function diagrams» and in Chapter «Diagnostics (Page 147).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 145
6.6 3UG4615 / 3UG4616 line monitoring relays Function diagrams 3UG4615 / 3UG4616 Display Memory = no Memory = no Relay switching behavior = NC Relay switching behavior = NO (closed-circuit principle) (open-circuit principle) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 146: Operation
NC / open-circuit principle NO) 3UG4615 line monitoring relay 3UG4616 line monitoring relay The parameters are described in the Chapter «Parameters (Page 363)». Menu-based operation is described in the Chapter «Menu-based operation (Page 39)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 147: Diagnostics
6.6.4.1 Indications on the display Display information The display is divided into three different areas. ① Voltage measured value or fault symbol ② Type of monitoring ③ Symbols of the changeover contacts 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 148
This can be achieved with the help of a sine-wave filter. You will find more information about the switching behavior of the output relays in Chapter «Functions (Page 143)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 149: Reset
2.5 s after removal of the cause of error. If the cause of the error has not been removed, a new error message appears immediately. Alternatively, the devices can be reset by switching the rated control supply voltage on and off. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 150: Circuit Diagrams
Internal circuit diagrams 3UG4615 / 3UG4616 3UG4615 line monitoring relay 3UG4616 line monitoring relay Note It is not necessary to fuse the measuring circuit to protect the device. Fusing for line protection depends on the cross-section used. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 151: Technical Data
• Starting time after the control supply voltage has been applied Response time maximum 0.45 Relative adjustment accuracy Relative metering precision Precision of digital display +/-1 digit Relative repeat accuracy 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 152
Electrostatic discharge according to 6 kV contact discharge / 8 kV air discharge IEC 61000-4-2 Field-bound parasitic coupling according to 10 V/m IEC 61000-4-3 Thermal current of the contact-affected switching element maximum 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 153
Mechanical operating cycles as operating time 10 000 000 typical Electrical operating cycles as operating time 100 000 at AC-15 at 230 V typical Operating cycles with 3RT2 contactor 5 000 maximum 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 154
Distance, to be maintained, to the ranks assembly forwards • backwards • sidewards • upwards • downwards • Distance, to be maintained, conductive elements forwards • backwards • sidewards • upwards • downwards • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 155
2x (24 … 16) – solid 2x (20 … 14) 2x (24 … 16) – stranded Tightening torque N·m 0.8 … 1.2 — … with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 156: 3Ug4617 / 3Ug4618 Line Monitoring Relays
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 165)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 157: Functions
You will find the setting ranges and factory settings of the available parameters in Chapter «Operation (Page 161).» You will find a description of the individual parameters in Chapter «Parameters (Page 363).» Note The specified voltages represent the absolute thresholds. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 158
Thanks to a special measuring method, a phase failure is detected with certainty despite wide-range voltage from 160 to 690 V AC and reverse power of up to 80 % from the load in the case of regenerative power recovery. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 159
The 3UG4617 and 3UG4618 line monitoring relays are only suitable for line frequencies of 50 / 60 Hz! You will find the switching states of the output relays below in the Section «Function diagrams» and in the Chapter «Diagnostics (Page 162).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 160
3UG4.1 line monitoring relay 6.7 3UG4617 / 3UG4618 line monitoring relays Function diagrams 3UG4617 / 3UG4618 Display Correct phase sequence L1-L2-L3 Incorrect phase sequence L3-L2-L1 Memory = no Memory = no 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 161: Operation
= Autoreset 3UG4617 line monitoring relay 3UG4618 line monitoring relay The parameters are described in the Chapter «Parameters (Page 363)». Menu-based operation is described in the Chapter «Menu-based operation (Page 39)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 162: Diagnostics
6.7.4.1 Indications on the display Display information The display is divided into three different areas. ① Voltage measured value or fault symbol ② Type of monitoring ③ Symbols of the changeover contacts 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 163
CO contact 1 switches on all types of error. CO contact 2 is for operating a reversing combination. You will find more information about the switching behavior of the output relays in Chapter «Functions (Page 157)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 164: Reset
2.5 s after removal of the cause of error. If the cause of the error has not been removed, a new error message appears immediately. Alternatively, the devices can be reset by switching the rated control supply voltage on and off. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 165: Circuit Diagrams
Internal circuit diagram 3UG4617 / 3UG4618 3UG4617 line monitoring relay 3UG4618 line monitoring relay Note It is not necessary to fuse the measuring circuit to protect the device. Fusing for line protection depends on the cross-section used. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 166: Wiring Examples
3UG4.1 line monitoring relay 6.7 3UG4617 / 3UG4618 line monitoring relays 6.7.5.2 Wiring examples Automatic phase correction Image 6-2 3UG4617 / 3UG4618 automatic phase correction 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 167: Technical Data
• overvoltage recognition of 3 phases • undervoltage recognition of 3 phases • tension window recognition of 3 phases • — reset external • self-reset • open-circuit or closed-circuit current principle • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 168
AC-15 • – at 250 V at 50/60 Hz – at 400 V at 50/60 Hz at DC-13 • – at 24 V – at 125 V – at 250 V 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 169
Mechanical operating cycles as operating time 10 000 000 typical Electrical operating cycles as operating time at 100 000 AC-15 at 230 V typical Operating cycles with 3RT2 contactor maximum 5 000 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 170
Distance, to be maintained, to the ranks assembly forwards • backwards • sidewards • upwards • downwards • Distance, to be maintained, conductive elements forwards • backwards • sidewards • upwards • downwards • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 171
2x (24 … 16) – solid 2x (20 … 14) 2x (24 … 16) – stranded Tightening torque N·m 0.8 … 1.2 — … with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 172
3UG4.1 line monitoring relay 6.7 3UG4617 / 3UG4618 line monitoring relays 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 173: 3Ug4621/3Ug4622 Current Monitoring Relays
Wire-break monitoring • Heating systems (electroplating plants, plastic • injection machines, paintshops) Lamps (tunnels, OP lighting, traffic lights, • signal systems, UV lamps, infrared radiators, laser lamps) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 174: Operator Controls And Connection Terminals
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 182)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 175: Functions
Note For AC currents I > 10 A, commercially available current transformers, e.g. 4NC, can be used as accessories. You will find more information in Catalog LV10 (www.siemens.com/lowvoltage/infomaterial). 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 176
NC or NO working principle. You will find the switching states of the output relay below in the section entitled «Function diagrams» and in Chapter «Diagnostics (Page 180).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 177
Relay switching behavior = NC (closed-circuit Relay switching behavior = NO (open-circuit principle) principle) = on = on J = Currently measured current value I = set threshold value for the current 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 178
Relay switching behavior = NO (open-circuit principle) principle) I > 3 mA / 50 mA I > 3 mA / 50 mA J = Currently measured current value I = set threshold value for the current 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 179: Operation
• Current overshoot • Current undershoot The up-to-date measured value is displayed permanently. The parameters are described in the Chapter «Parameters (Page 363)». Menu-based operation is described in the Chapter «Menu-based operation (Page 39)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 180: Diagnostics
Flashing: Delay time (ON-delay or tripping delay) running • Masked out: Relay contact 11/12 closed, relay contact 11/14 open • You will find more information about the switching behavior of the output relay in Chapter «Functions (Page 175).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 181: Reset
2.5 s after removal of the cause of error. If the cause of the error has not been removed, a new error message appears immediately. Alternatively, the devices can be reset by switching the rated control supply voltage on and off. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 182: Circuit Diagrams
On the 24 to 240 V AC/DC versions of the 3UG4621/22-.AW30, terminals A2 and M (GND) are electrically separated! 7.6.2 Wiring examples (3UG46..-.AW30) Single-phase operation Three-phase operation 3UG462.-.AW30 single-phase operation 3UG462.-.AW30 three-phase operation 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 183: Wiring Examples (3Ug462.-.Aa30)
If the load to be monitored and the current monitoring relay are powered from the same system, terminal A2 is not required! The load current must always flow away through M (GND), otherwise the current monitoring relay may be destroyed! 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 184: Technical Data
Adjustable switching hysteresis for 0.1 … 250 10 … 5 000 measured current value Stored energy time at mains power cut minimum Operating voltage 24 … 240 24 … 240 rated value • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 185
Starting time after the control supply voltage has been applied Response time maximum Relative metering precision Precision of digital display +/-1 digit Relative temperature-related measurement deviation Temperature drift per °C %/°C Relative repeat accuracy 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 186
400 V at 50/60 Hz – at DC-13 – at 24 V – at 125 V – at 250 V for permanent overcurrent • maximum permissible for overcurrent duration • < 1 s maximum permissible 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 187
Mechanical operating cycles as 10 000 000 operating time typical Electrical operating cycles as 100 000 operating time at AC-15 at 230 V typical Operating cycles with 3RT2 5 000 contactor maximum 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 188
Distance, to be maintained, to the ranks assembly forwards • backwards • sidewards • upwards • downwards • Distance, to be maintained, conductive elements forwards • backwards • sidewards • upwards • downwards • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 189
2x (24 … 16) – solid 2x (20 … 14) 2x (24 … 16) – stranded Tightening torque N·m 0.8 … 1.2 — … with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 190
3UG4621/3UG4622 current monitoring relays 7.7 Technical data 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 191: 3Ug4625 Residual Current Monitoring Relay With 3Ul23 Transformer
Diminishing insulation caused by material wear Furnaces • • Note 3UG4625 residual current monitoring relays monitor devices and systems for their correct function. They are not suitable for personal protection or protection from fires. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 192: Operator Controls And Connection Terminals
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 206)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 193: Functions
This current is evaluated in the monitoring relay and used to display the current residual current and to switch the output relays when the set warning threshold or the tripping threshold is overshot. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 194
The measuring accuracy is -7.5 %/+7.5 % of the value displayed. This takes into account the measuring accuracy of monitoring relay and residual current transformer. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 195
To avoid these types of measuring errors and false tripping, we recommend to set the limit values to the minimum values listed in the following graphic, depending on the applicable primary current. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 196
In the case of extreme peak values of the residual current, the measuring accuracy suffers as a result of this principle. Due to the great difference between the peak value and the rms value, monitoring for lower limits is useful. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 197
On the display, the actual measured value and the symbol for overshoot flash. You will find the switching states of the output relays below in section «Function diagrams» and in Chapter «Diagnostics (Page 203).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 198
These necessary accessories are described in Chapter «3UL23 residual current transformers for 3UG4625 monitoring relays (Page 333).» Note Do not ground the neutral conductor downstream of the residual current transformer as otherwise fault current monitoring functions can no longer be ensured. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 199
I▲ / I! Mem = no Init = ERR Display Memory = no; Init = ERR Relay switching behavior = NC (closed-circuit principle) I▲ / I! Mem = no Init = ERR 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 200
I▲ / I! Mem = yes Init = ERR Display Memory = no; Init = OK Relay switching behavior = NO (open-circuit principle) I▲ / I! Mem = no Init = OK 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 201
Relay switching behavior = NC (closed-circuit principle) I▲ / I! Mem = yes Init = OK Note The system is immediately switched off in the event of an open-circuit or short-circuit in the transformer connection cables. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 202: Operation
The 3UL23 residual current transformers used cover the entire fault current range from 0.03 to 40 A in all sizes. For more information on the technical data of 3UL23 residual current transformers see Chapter «Technical data (Page 346)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 203: Diagnostics
8.5.1 Indications on the display Display information The display is divided into three different areas. ① Current measured value or fault symbol ② Type of monitoring ③ Symbols of the changeover contacts 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 204
Measurement range exceeded (> 40 A) ① 0.00A Fallen below measurement range ① Open circuit (flashing) ① Short-circuit (flashing) You will find more information about the switching behavior of the output relay in Chapter «Functions (Page 193).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 205: Reset
Alternatively, the devices can be reset by switching the rated control supply voltage on and off. Note The warning threshold is always reset by autoreset. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 206: Circuit Diagrams
3UL23 residual current transformer is connected to terminals C1 and C2 of the monitoring relay. To avoid interference injection, which could result in incorrect measurements, these connecting lines must be routed as parallel as possible and twisted, or shielded cables must be used. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 207: Wiring Examples
3UG4625 residual current monitoring relay with 3UL23 transformer 8.6 Circuit diagrams 8.6.2 Wiring examples ① Cable shielding recommended Image 8-1 Wiring diagram of 3UG4625 with 3UL23 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 208: Technical Data
Starting time after the control supply voltage has been 1 600 applied Response time maximum Relative metering precision Precision of digital display +/-1 digit Temperature drift per °C %/°C Relative repeat accuracy 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 209
Conductor-bound parasitic coupling BURST according to 2 kV IEC 61000-4-4 Conductor-bound parasitic coupling conductor-earth SURGE 2 kV according to IEC 61000-4-5 Conductor-bound parasitic coupling conductor-conductor 1 kV SURGE according to IEC 61000-4-5 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 210
Mechanical operating cycles as operating time typical 10 000 000 Electrical operating cycles as operating time at AC-15 at 100 000 230 V typical Operating cycles with 3RT2 contactor maximum 5 000 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 211
2x (20 … 14) 2x (24 … 16) – stranded 2x (20 … 14) 2x (24 … 16) Tightening torque N·m 0.8 … 1.2 — with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 212
3UG4625 residual current monitoring relay with 3UL23 transformer 8.7 Technical data 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 213: 3Ug458. Insulation Monitoring Relay
This procedure enables controlled shutdown, or correction of the fault without interrupting the power supply. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 214
● Ungrounded, mixed DC systems and AC systems for insulation faults (e.g. AC systems with rectifiers or switched-mode power supplies) Note The use of two 3UG458 devices in a galvanically connected area (monitored area) is not permissible. ① Monitored area 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 215: Application Areas
2p: Monitoring is 2-phase 2p + N: Monitoring is 2-phase + N conductor 3p: Monitoring is 3-phase 3p + N: Monitoring is 3-phase + N conductor — : Function not available Configurable 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 216: Performance Features Of The Insulation Monitoring Relays
+ 1 changeover contact, adjustable Number of thresholds ✓ ✓ — • — — ✓ 1 or 2, adjustable • Functional principle Closed-circuit principle Closed-circuit principle Open-circuit principle or closed- circuit principle, configurable 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 217
Retentive fault memory — — ✓ Open-circuit detection — — ✓ ✓: Function available — : Function not available With 3UG4983-1A upstream module Configurable 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 218: 3Ug4581 Insulation Monitoring Relay
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Technical data (Page 233)». You can find information on connecting in the Chapter «Circuit diagrams (Page 227)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 219: Functions
The insulation resistance of the system is calculated with the help of the overlaid DC measuring voltage and the resulting current. The 3UG4581 insulation monitoring relays can be configured to the relevant application conditions and are therefore versatile in use. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 220
If the continuously present rated system voltage is greater than 240 V, a minimum gap of 10 mm must be maintained to the next device. You will find the switching states of the output relay below in the section «Functions (Page 219)» and in Chapter «Diagnostics (Page 226)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 221
2) Remote reset (remote button with NC function) 3) A1+ / A2- (switching the supply voltage off/on) 1) On the front (Test/Reset button) 2) A1+ / A2- (switching the supply voltage off/on) 1) Autoreset (factory setting) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 222
Without fault storage, autoreset ① Test (Y1-Y3) ② Reset (Y2-Y3) ③ Measured value ④ Hysteresis ⑤ Threshold ⑥ Green ⑦ ⑧ Yellow = Time for internal device test after applying the supply voltage 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 223
With fault storage, manual RESET ① Test (Y1-Y3) ② Reset (Y2-Y3) ③ Measured value ④ Hysteresis ⑤ Threshold ⑥ Green ⑦ ⑧ Yellow = Time for internal device test after applying the supply voltage 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 224: Operator Control
Chapter «Internal circuit diagrams (Page 227)» shows examples for the different monitoring modes. The parameters are defined in the Chapter «Parameters (Page 363)». Tools required The same screwdriver can be used to set the parameters as for wiring the insulation monitoring relays. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 225
The test function can be started again at any time via the Test/Reset button on the front or via a remote test button. The graphic below shows the connection of the button for the remote test. Image 9-1 Remote test button 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 226: Diagnostics
The device has tripped following an insulation fault. The fault has been stored and the insulation resistance has reverted to a value above the set threshold including hysteresis. Dependent on the fault. The switching behavior of the output relay is shown in Chapter «Functions (Page 219)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 227: Circuit Diagrams
3UG458. insulation monitoring relay 9.3 3UG4581 insulation monitoring relay 9.3.5 Circuit diagrams 9.3.5.1 Internal circuit diagrams Internal circuit diagram 3UG4581-1AW30 insulation monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 228
Measuring input L can be connected to any conductor (phase or N conductor). The rated system voltage must be U ≤ 400 V AC (50 to 60 Hz). 2-wire AC system 3-wire AC system 4-wire AC system 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 229
Image 9-2 Monitoring for ground fault/insulation fault in the case of an ungrounded 2-wire IT AC system Note The maximum cable length of the control cables is 50 m or 100 pF/m. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 230
Image 9-3 Monitoring for ground fault/insulation fault in the case of an ungrounded 4-wire IT AC system Note The maximum cable length of the control cables is 50 m or 100 pF/m. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 231: Characteristics
Characteristic curves of the 3UG4581 insulation monitoring relays The characteristics below show the load limit curves of the 3UG4581 insulation monitoring relays. Image 9-4 AC load (resistive) Image 9-5 DC load (resistive) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 232
9.3 3UG4581 insulation monitoring relay Image 9-6 Reduction factor F in the case of inductive AC load ① Operating cycles ② 250 V, resistive load ③ Switching current Image 9-7 Contact service life 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 233: Technical Data
Protection class IP IP20 Ambient temperature °C -25 … +60 during operating • Item designation according to DIN EN 61346-2 Item designation according to DIN 40719 extendable after IEC 204-2 according to IEC 750 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 234
20 … 12 solid • AWG number as coded connectable conductor cross section 18 … 14 stranded • Tightening torque N·m 0.6 … 0.8 with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 235: 3Ug4582/3Ug4583 Insulation Monitoring Relays
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Technical data (Page 265)». You can find information on connecting in the Chapter «Circuit diagrams (Page 255)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 236
Output relay K1 CO contact root Output relay K1 CO contact NO contact Output relay K2 CO contact NC contact Output relay K2 CO contact root Output relay K2 CO contact NO contact 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 237
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Technical data (Page 265)». You can find information on connecting in the Chapter «Circuit diagrams (Page 255)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 238: Functions
K1 responds depending on the device configuration. This adaptive measuring principle is suitable for detecting symmetrical insulation faults. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 239
The output relays would only pick up if an insulation fault or internal device faults are detected. However, the fault «Missing supply voltage» can then no longer be detected. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 240
(Page 243)» and in the Chapter «Diagnostics (Page 253)». You will find the setting ranges and factory settings of the available parameters, and the definitions of the DIP switch positions in the Chapter «Operator control (Page 249)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 241
2) Remote reset (remote button with NC function) 3) A1+ / A2- (switching the supply voltage off/on) 1) On the front (Test/Reset button) 2) A1+ / A2- (switching the supply voltage off/on) 1) Autoreset (factory setting) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 242
690 V AC and 1000 V DC. The upstream module is connected to terminals VS, V1+ and V1- of the insulation monitoring relay. These accessories are described in Chapter «3UG4983 upstream module for the 3UG4583 monitoring relay (Page 353)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 243: Function Diagrams
Without fault storage, autoreset ① Test (Y1-Y3) ② Reset (Y2-Y3) ③ Measured value ④ Hysteresis ⑤ Threshold ⑥ Green ⑦ ⑧ Yellow = Time for internal device test after applying the supply voltage 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 244
With fault storage, manual RESET ① Test (Y1-Y3) ② Reset (Y2-Y3) ③ Measured value ④ Hysteresis ⑤ Threshold ⑥ Green ⑦ ⑧ Yellow = Time for internal device test after applying the supply voltage 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 245
With fault storage, manual RESET, 1 x 2 changeover contacts, shutdown principle) ① Test (Y1-Y3) ② Reset (Y2-Y3) ③ Measured value ④ Hysteresis ⑤ Threshold ⑥ Green ⑦ ⑧ Yellow = Time for internal device test after applying the supply voltage 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 246
With fault storage, manual RESET, 1 x 2 changeover contacts, shutdown principle) ① Test (Y1-Y3) ② Reset (Y2-Y3) ③ Measured value ④ Hysteresis ⑤ Threshold ⑥ Green ⑦ ⑧ Yellow = Time for internal device test after applying the supply voltage 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 247
① Test (Y1-Y3) ② Reset (Y2-Y3) ③ Measured value ④ Hysteresis ⑤ Warning ⑥ Shutdown ⑦ Green ⑧ ⑨ Yellow = Time for internal device test after applying the supply voltage 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 248
① Test (Y1-Y3) ② Reset (Y2-Y3) ③ Measured value ④ Hysteresis ⑤ Warning ⑥ Shutdown ⑦ Green ⑧ ⑨ Yellow = Time for internal device test after applying the supply voltage 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 249: Operator Control
The threshold is derived from the sum of the two set values. If, for example, threshold R.1-value is set to 70 and threshold R.2-value is set to 8 on the 3UG4582, threshold R corresponds to 78 kΩ. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 250
Functional principle of fault storage output relays K1 and K2 ON ↑ 2 x 1 changeover contacts Activated Activated Closed-circuit principle NC 1 x 2 changeover contacts Deactivated Deactivated Open-circuit principle NO 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 251
Chapter «Wiring examples (Page 256)» shows the examples for the different monitoring modes. The parameters are defined in the Chapter «Parameters (Page 363)». Tools required The same screwdriver can be used to set the parameters as for wiring the insulation monitoring relays. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 252
The test function can be started again at any time via the Test/Reset button on the front or via a remote test button. The graphic below shows the connection of the button for the remote test. Image 9-8 Remote test button 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 253: Diagnostics
Internal fault On the 3UG4582: On the 3UG4582: Off • • On the 3UG4583: Dependent • On the 3UG4583: on the configuration • Dependent on the configuration 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 254
The device has tripped following an insulation fault. The fault has been stored and the insulation resistance has reverted to a value above the set threshold including hysteresis. Dependent on the fault. The switching behavior of the output relay is shown in Chapter «Functions (Page 238)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 255: Circuit Diagrams
3UG458. insulation monitoring relay 9.4 3UG4582/3UG4583 insulation monitoring relays 9.4.5 Circuit diagrams 9.4.5.1 Internal circuit diagrams Internal circuit diagrams 3UG4582-1AW30 / 3UG4583-1CW30 3UG4582-1AW30 insulation monitoring relay 3UG4583-1CW30 insulation monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 256: Wiring Examples
2-wire AC system / 2-wire DC system 2-wire AC system 2-wire DC system 3-wire AC system / 3-wire DC system 3-wire AC system 3-wire DC system 4-wire AC system 4-wire AC system 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 257
④ Loads Image 9-9 Monitoring for ground fault/insulation fault with different load circuits Note The maximum cable length of the control cables is 50 m or 100 pF/m. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 258
1A upstream module must be used to monitor systems with higher voltages. 2-wire AC system / 2-wire DC system 2-wire AC system 2-wire DC system 3-wire AC system/3-wire DC system 3-wire AC system 3-wire DC system 4-wire AC system 4-wire AC system 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 259
Loads Image 9-10 Monitoring for ground fault/insulation fault in the case of an ungrounded 4-wire AC system Note The maximum cable length of the control cables is 50 m or 100 pF/m. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 260
④ Loads Image 9-11 Monitoring for ground fault/insulation fault with different load circuits Note The maximum cable length of the control cables is 50 m or 100 pF/m. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 261: Characteristics
Characteristics Characteristics of the 3UG4582 insulation monitoring relays The characteristics below show the load limit curves of the 3UG4582 insulation monitoring relays. Image 9-12 AC load (resistive) Image 9-13 DC load (resistive) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 262
9.4 3UG4582/3UG4583 insulation monitoring relays Image 9-14 Reduction factor F in the case of inductive AC load ① Operating cycles ② 250 V, resistive load ③ Switching current Image 9-15 Contact service life 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 263
9.4 3UG4582/3UG4583 insulation monitoring relays Characteristics of the 3UG4583 insulation monitoring relays The characteristics below show the load limit curves of the 3UG4583 insulation monitoring relays. Image 9-16 AC load (resistive) Image 9-17 DC load (resistive) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 264
9.4 3UG4582/3UG4583 insulation monitoring relays Image 9-18 Reduction factor F in the case of inductive AC load ① Operating cycles ② 250 V, resistive load ③ Switching current Image 9-19 Contact service life 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 265: Technical Data
DC • 24 … 240 – rated value at 50 Hz at AC • 24 … 240 – rated value at 60 Hz at AC • 24 … 240 – rated value 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 266
Protection class IP IP20 Ambient temperature °C -25 … +60 during operating • Item designation according to DIN EN 61346-2 • according to DIN 40719 extendable after • IEC 204-2 according to IEC 750 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 267
Distance, to be maintained, conductive elements forwards • backwards • sidewards • upwards • downwards • Distance, to be maintained, to earthed part forwards • backwards • sidewards • upwards • downwards • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 268
AWG number as coded connectable conductor cross section 20 … 12 … solid • 18 … 14 stranded • Tightening torque N·m 0.6 … 0.8 with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 269: 3Ug4583
Protection class IP IP20 Ambient temperature °C -25 … +60 during operating • Item designation according to DIN EN 61346-2 • according to DIN 40719 extendable after IEC 204-2 according to • IEC 750 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 270
AWG number as coded connectable conductor cross section 20 … 12 solid • 18 … 14 stranded • Tightening torque N·m 0.6 … 0.8 with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 271: 3Ug463. Voltage Monitoring Relay
System protection against destruction caused by supply overvoltages • Energy supply to the line • Machine switch-on when a defined voltage is reached • Threshold switch for analog signals from 0.1 to 10 V • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 272: 3Ug4631 / 3Ug4632 Voltage Monitoring Relay
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 281)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 273: Functions
0.0 V and shows a symbol for voltage overshoot monitoring, voltage undershoot monitoring, or range monitoring. You will find the switching states of the output relay below in the section entitled «Function diagrams» and in Chapter «Diagnostics (Page 279).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 274
10.2 3UG4631 / 3UG4632 voltage monitoring relay Function diagrams 3UG4631 / 3UG4632 Display Memory = no Memory = no Relay switching behavior = NC Relay switching behavior = NO (closed-circuit principle) (open-circuit principle) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 275: 3Ug4633 Voltage Monitoring Relay
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 281)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 276: Functions
You will find the switching states of the output relay below in the section entitled «Function diagrams» and in Chapter «Diagnostics (Page 279).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 277
3UG463. voltage monitoring relay 10.3 3UG4633 voltage monitoring relay Function diagrams 3UG4633 Display Memory = no Memory = no Relay switching behavior = NC Relay switching behavior = NO (closed-circuit principle) (open-circuit principle) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 278: Operation
• Voltage overshoot • Voltage undershoot The up-to-date measured value is displayed permanently. The parameters are described in Chapter «Parameters (Page 363).» Menu-based operation is described in Chapter «Menu-based operation (Page 39).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 279: Diagnostics
Masked out: Relay contact 11/12 closed, relay contact 11/14 open • You will find more information about the switching behavior of the output relay in Chapter «Functions (Page 273)» (3UG4631 / 3UG4632) and «Functions (Page 276)» (3UG4633). 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 280: Reset
2.5 s after removal of the cause of error. If the cause of the error has not been removed, a new error message appears immediately. Alternatively, the devices can be reset by switching the rated control supply voltage on and off. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 281: Circuit Diagrams
On the 24 V AC/DC versions of the 3UG4631-.AA30 and 3UG4632-.AA30, terminals A2 and M (GND) are electrically connected in the device! On the 24 to 240 V AC/DC versions of the 3UG4631-.AW30 and 3UG4632-.AW30, terminals A2 and M (GND) are electrically separated! 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 282: Wiring Examples
3UG463. voltage monitoring relay 10.6 Circuit diagrams 10.6.2 Wiring examples 3UG4631-.AA30 / 3UG4632-.AA30 Image 10-1 3UG4631-.AA30 / 3UG4632-.AA30 3UG4631-.AW30 / 3UG4632-.AW30 Image 10-2 3UG4631-.AW30 / 3UG4632-.AW30 3UG4633 Image 10-3 3UG4633 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 283: Technical Data
10 … 600 17 … 275 voltage range Adjustable response delay time — — 0.1 … 20 — 0.1 … 20 when • starting 0.1 … 20 with lower • or upper limit violation 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 284
• recognition DC undervoltage • recognition of 1 phase undervoltage • recognition of 3 phases undervoltage • recognition DC reset external • self-reset • open-circuit or • closed-circuit current principle 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 285
0.85 … 1.15 0.85 … 1.1 0.85 … 1.15 0.85 … 1.1 at 60 Hz for • 0.85 … 1.15 0.85 … 1.1 0.85 … 1.15 0.85 … 1.1 for DC • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 286
SURGE according to IEC 61000-4-5 Conductor-bound 1 kV parasitic coupling conductor-conductor SURGE according to IEC 61000-4-5 Electrostatic 6 kV contact discharge / 8 kV air discharge discharge according to IEC 61000-4-2 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 287
Mechanical operating 10 000 000 cycles as operating time typical Electrical operating 100 000 cycles as operating time at AC-15 at 230 V typical Operating cycles 5 000 with 3RT2 contactor maximum 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 288
2x (24 … 16) – solid 2x (20 … 14) 2x (24 … 16) – stranded Tightening torque N·m 1.2 … 0.8 — … with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 289: 3Ug4641 Cos Phi And Active Current Monitoring Relay
• Conveyor belt • Surface grinding machine • Breaking mill • Milling machine • Car wash • Lifting platform • Screw conveyor • Crane • Turning machine • Infrared heating system • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 290: Operator Controls And Connection Terminals
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 299)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 291: Functions
Note In the case of active currents I > 10 A, commercially available current transformers, e.g. 4NC, can be used as accessories. You will find more information in Catalog LV10 (www.siemens.com/lowvoltage/infomaterial). 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 292
On the display, the current measuring value and the symbol for undershoot or overshoot flash. You will find the switching states of the output relays below in section «Function diagrams» and in Chapter «Diagnostics (Page 297).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 293
Memory = no Memory = no Relay switching behavior = NC (closed-circuit Relay switching behavior = NO (open-circuit principle) principle) J = currently set current value I = set threshold value for the current 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 294
Memory = no Memory = no Relay switching behavior = NC (closed-circuit Relay switching behavior = NO (open-circuit principle) principle) J = currently set current value I = set threshold value for the current 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 295
Relay switching behavior = NC (closed-circuit Relay switching behavior = NO (open-circuit principle) principle) cos φ = currently set value for cos φ PF = power factor = set threshold for cos φ 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 296: Operation
The monitoring mode «Overshoot» or «Undershoot» is defined with the setting OFF at the threshold for undershoot or overshoot. The parameters are described in Chapter «Parameters (Page 363).» Menu-based operation is described in Chapter «Menu-based operation (Page 39).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 297: Diagnostics
Flashing: Delay time (ON-delay or tripping delay) running • Masked out: Relay contact 21/22 closed, relay contact 21/24 open • You will find more information about the switching behavior of the output relay in Chapter «Functions (Page 291).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 298: Reset
2.5 s after removal of the cause of error. If the cause of the error has not been removed, a new error message appears immediately. Alternatively, the devices can be reset by switching the rated control supply voltage on and off. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 299: Circuit Diagrams
3UG4641 cos phi and active current monitoring relay 11.6 Circuit diagrams 11.6 Circuit diagrams 11.6.1 Internal circuit diagrams Internal circuit diagrams 3UG4641 3UG4641 cos phi and active current monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 300: Wiring Examples
Cos phi and active current monitoring for single-phase motors Cos phi and active current monitoring for three-phase motors Cos phi and active current monitoring for Cos phi and active current monitoring for three-phase motors three-phase motors (with neutral conductor) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 301
Cos phi and active current monitoring for three-phase motors with transformers for currents Cos phi and active current monitoring for Cos phi and active current monitoring for three-phase motors with three-phase motors with transformers for currents transformer for currents (with neutral conductor) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 302: Technical Data
• Adjustable switching hysteresis for measured current 0.1 … 2 value Stored energy time at mains power cut minimum Operating voltage 90 … 690 rated value • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 303
1 … 6 Hz: 15 mm, 6 … 500 Hz: 2g IEC 60068-2-6 Resistance against shock according to sinusoidal half-wave 15g / 11 ms IEC 60068-2-27 Installation altitude at a height over sea level 2 000 maximum 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 304
Mechanical operating cycles as operating time 10 000 000 typical Electrical operating cycles as operating time at 100 000 AC-15 at 230 V typical Operating cycles with 3RT2 contactor maximum 5 000 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 305
• Distance, to be maintained, conductive elements forwards • backwards • sidewards • upwards • downwards • Type of mounting snap-on mounting Product function removable terminal for auxiliary and control circuit 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 306
2x (24 … 16) – solid 2x (20 … 14) 2x (24 … 16) – stranded Tightening torque N·m 1.2 … 0.8 — … with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 307: 3Ug4651 Speed Monitoring Relay
The speed monitoring relays can also be used for all functions where a continuous pulse signal is to be monitored (e.g. belt travel monitoring, completeness check, pass monitoring, or cycle time monitoring). 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 308: Operator Controls And Connection Terminals
You can find additional information on the connection terminals and the permissible conductor cross-sections in the Chapter «Connection methods (Page 21)». You can find information on connecting in the Chapter «Circuit diagrams (Page 315)». 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 309: Functions
5 ms. A pause is detected when the voltage level < 1 V. A pulse requires a minimum value of 4.5 V. Alternatively, a two-wire NAMUR sensor supplied from terminal 8V2, or a mechanical contact, can be connected at terminal IN2. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 310
ON-delay time (onDel) and the drive (with a second contact, for example) be started. You will find the switching states of the output relay below in the section entitled «Function diagrams» and in Chapter «Diagnostics (Page 313).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 311
= set threshold for the speed Note The relay control for the open-circuit principle NO is inverted to the represented function diagrams in the closed-circuit principle NC after application of the rated control supply voltage U 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 312: Operation
The monitoring mode «Overshoot» or «Undershoot» is defined with the setting OFF at the threshold for undershoot or overshoot. The parameters are described in Chapter «Parameters (Page 363).» Menu-based operation is described in Chapter «Menu-based operation (Page 39).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 313: Diagnostics
Flashing: Delay time (ON-delay or tripping delay) running • Masked out: Relay contact 11/12 closed, relay contact 11/14 open • You will find more information about the switching behavior of the output relay in Chapter «Functions (Page 309).» 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 314: Reset
2.5 s after removal of the cause of error. If the cause of the error has not been removed, a new error message appears immediately. Alternatively, the devices can be reset by switching the rated control supply voltage on and off. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 315: Circuit Diagrams
On the 24 V AC/DC versions of the 3UG4651-.AA30, terminals A1 / A2 and 0V / 24V are electrically connected in the device! On the 24 to 240 V AC / DC versions of the 3UG4651-.AW30, terminals A1 / A2 and 0V / 24V are electrically separated! 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 316: Wiring Examples
3UG4651 speed monitoring relay 12.6 Circuit diagrams 12.6.2 Wiring examples Speed monitoring relays without Enable input Speed monitoring relays with Enable input 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 317: Technical Data
Input current at the digital input 1 maximum Pulse duration minimum Pulse interval minimum Number of sensor signals per revolution 1 … 10 Switching hysteresis for rotational speed 1/min 0 … 99.9 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 318
– delayed switching – non-delayed Response time maximum Stored energy time at mains power cut minimum ms Relative metering precision Precision of digital display +/- 1 Digit Relative repeat accuracy 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 319
Conductor-bound parasitic coupling BURST 2 kV according to IEC 61000-4-4 Conductor-bound parasitic coupling conductor-earth 2 kV SURGE according to IEC 61000-4-5 Conductor-bound parasitic coupling conductor- 1 kV conductor SURGE according to IEC 61000-4-5 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 320
AC-15 at 230 V typical Operating cycles with 3RT2 contactor maximum 5 000 Acceptability for application safety-related circuits Category according to EN 954-1 none safety Integrated Level according to IEC 61508 none 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 321
Distance, to be maintained, to the ranks assembly forwards • backwards • sidewards • upwards • downwards • Distance, to be maintained, conductive elements forwards • backwards • sidewards • upwards • downwards • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 322
– stranded Tightening torque N·m 0.8 … 1.2 — … with screw-type terminals • Number of NO contacts delayed switching Number of NC contacts delayed switching Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 323: Accessories
Siemens also offers a sealable membrane (3TK2820-0AA00) for securing the current monitoring relays with analog setting. The sealable membrane is fixed to the front of the device and secures the rotary buttons and sliding switches against unintentional tampering.
-
Page 324: Terminal Support For Stand-Alone Assembly
3RB3 solid-state overload relay. Table 13- 2 Stand-alone assembly of the 3RR2 current monitoring relay Size Connection system Terminal support for stand-alone assembly Screw-type 3RU2916-3AA01 Spring-loaded 3RU2916-3AC01 Screw-type 3RU2926-3AA01 Spring-loaded 3RU2926-3AC01 Screw-type 3RU2936-3AA01 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 325
Insert the contacts (a) into the central opening of the main terminals on the terminal support, with the contacts flush to the right. Make sure that the guide tabs are inserted into the designated slots on the terminal support. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 326
Position the screwdriver on the terminal support as shown in the figure. Carefully dislodge the current monitoring relay from the contactor. Pull the current monitoring relay toward you and away from the terminal support. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 327: Accessories For 3Ug4 Monitoring Relays
The sealable cover can be used to secure the actuators (rotary buttons, sliding switches, and keys) of the monitoring relays against unauthorized or unintentional manipulation. Siemens also offers a sealable membrane (3TK2820-0AA00) for securing the monitoring relays with analog setting. The sealable membrane is affixed to the front of the device and secures rotary buttons and sliding switches against unintentional manipulation.
-
Page 328: Push-In Lugs
Accessories 13.2 Accessories for 3UG4 monitoring relays 13.2.2 Push-in lugs Description The 3RP1903 push-in lugs are available for the monitoring relays. With the help of the push-in lugs, the monitoring relays can be secured with screws on a level surface (e.g. a wall). Two push-in lugs are required per device.
-
Page 329: Probes For The 3Ug4501 Monitoring Relay
Accessories 13.2 Accessories for 3UG4 monitoring relays 13.2.3 Probes for the 3UG4501 monitoring relay 3UG3207-3A three-pole wire electrode The 3UG3207-3A three-pole wire electrode can be used for two-point filling level controls in an insulating tank. In addition to the common reference electrode there is one electrode for the min.
-
Page 330
Accessories 13.2 Accessories for 3UG4 monitoring relays 3UG3207-2B two-pole bow electrode Because of the small space requirement on side installation, the 3UG3207-2B two-pole bow electrode for leakage monitoring and level monitoring can be used in small vessels and tubes. The probe can also be used to warn of the ingress of water into a casing. -
Page 331
Accessories 13.2 Accessories for 3UG4 monitoring relays Technical data Table 13- 9 Technical data — Probes for the 3UG4501 monitoring relay Order number 3UG3207-3A 3UG3207-2A 3UG3207-2B 3UG3207-1B 3UG3207-1C Three-pole Two-pole Two-pole Single-pole Single-pole Length — — — Insulation (Teflon —… -
Page 332: Summation Current Transformer For The 3Ug4624 Monitoring Relay
Accessories 13.2 Accessories for 3UG4 monitoring relays 13.2.4 Summation current transformer for the 3UG4624 monitoring relay Description The 3UL22 summation current transformers acquire residual current in machines and plants. Together with the 3UG4624 residual current monitoring relay or the motor management and control unit SIMOCODE 3UF, residual current monitoring and ground-fault monitoring are possible.
-
Page 333: 3Ul23 Residual Current Transformers For 3Ug4625 Monitoring Relays
This type of fault current can be detected by type A transformers in accordance with DIN VDE 0100-530, such as 3UL23 residual current transformers. Note 3UG4.25 residual current monitoring relays are only suitable for use with 3UL23 residual current transformers. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 334
13.2 Accessories for 3UG4 monitoring relays ① Suitable FI type ② Circuit ③ Load current ④ Fault current Image 13-7 Possible fault current forms and suitable residual current devices More information is available on the Internet (www.siemens.com/industrial-controls/support). 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 335: Installation Specifications
Accessories 13.2 Accessories for 3UG4 monitoring relays 13.2.5.2 Installation specifications Note Please ensure strict adherence to the installation specifications for live cables. WARNING Open-circuit voltage may result in death, serious injury or material damage The current transformer output is a constant current power supply. In accordance with U = R * I, the output voltage increases with an increasing resistance.
-
Page 336
Accessories 13.2 Accessories for 3UG4 monitoring relays All live cables must be routed as close to the center of the transformer as possible. Any neutral conductor must be routed through the transformer. Grounded protective conductors must not be routed through the transformer or need to be routed through the transformer in both directions. -
Page 337
Accessories 13.2 Accessories for 3UG4 monitoring relays Route power cables around the residual current transformer in a straight line and ensure the area corresponds at minimum to the internal transformer diameter. X > ∅ residual current transformer The internal transformer diameter must be at minimum twice the size of the power cable bundle diameter. -
Page 338
Accessories 13.2 Accessories for 3UG4 monitoring relays Transformer connection Transformer connecting cables must be twisted and not routed in parallel to live cables to protect from emitted interference. Keep the length of the connecting cables to a minimum. The resistance at the transformer connecting cable must not exceed 5 Ω to ensure correct fault current monitoring. -
Page 339: Potential For Optimization
Accessories 13.2 Accessories for 3UG4 monitoring relays 13.2.5.3 Potential for optimization Potential for optimization in the event of extremely high currents, false tripping due to high starting currents or in environments with high EMC interference 1. Extend the ON-delay time to fade out fault currents measured during motor startup.
-
Page 340
Accessories 13.2 Accessories for 3UG4 monitoring relays b) A solid shield sleeve, e.g. turned from a normal, low-carbon tool steel must be precisely in contact with the internal ring of the residual current transformer. The wall thickness of the sleeve must be 1 mm at minimum, the length of the sleeve (L) must correspond to the internal diameter of the transformer used. -
Page 341: Installation Faults
Accessories 13.2 Accessories for 3UG4 monitoring relays 13.2.5.4 Installation faults For reasons of clarity, the representations show only the residual current transformer with the currents passing through it rather than the complete residual current monitoring unit and residual current transformer. If the vectorial sum of the currents passing through the residual…
-
Page 342
Accessories 13.2 Accessories for 3UG4 monitoring relays Mixing up conductors In a network with several loads there is the risk that active conductors of loads that are to be separately monitored for fault currents can get mixed up. This fault leads to false tripping as the inflowing and outflowing currents are not always exactly the same strength, even if the loads are identical. -
Page 343: Internal Circuit Diagram
Accessories 13.2 Accessories for 3UG4 monitoring relays Routing contrary to the current flow To be able to form the vectorial sum of currents to and from a load correctly, all active conductors must be routed through the residual current transformer from the same direction.
-
Page 344: Installing
Accessories 13.2 Accessories for 3UG4 monitoring relays 13.2.5.6 Installing Wall mounting procedure Step Instructions Figure 1 / 2 Insert the fixing lugs into the designated openings in the unit until they reach the stop. Place the device against the wall surface prepared for establishing a screw connection.
-
Page 345
Accessories 13.2 Accessories for 3UG4 monitoring relays Mounting onto standard rail Requirement: At the installation location, a horizontal 35-mm wide mounting rail in accordance with DIN EN 60715 has been properly secured. Rail mounting is possible with residual current transformers with bushing opening diameters of up to ∅… -
Page 346: Technical Data
Accessories 13.2 Accessories for 3UG4 monitoring relays 13.2.5.7 Technical data 3UL2302/3UL2303/3UL2304 residual current transformers for fault current monitoring 3UL2302-1A 3UL2303-1A 3UL2304-1A Product equipment touch-protection Height Width 124.5 Depth 75.5 Ambient temperature °C -25 … +60 during operating • Type of mounting…
-
Page 347
Accessories 13.2 Accessories for 3UG4 monitoring relays 3UL2305/3UL2306/3UL2307 residual current transformers for fault current monitoring 3UL2305-1A 3UL2306-1A 3UL2307-1A Product equipment touch-protection Height Width Depth 207.5 Ambient temperature °C -25 … +60 during operating • Type of mounting screw fixing Diameter of the feedthrough Conductor cross section that can be mm²… -
Page 348: Dimension Drawings
Accessories 13.2 Accessories for 3UG4 monitoring relays 13.2.5.8 Dimension drawings 3UL23 residual current transformer Image 13-9 3UL2302-1A 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 349
Accessories 13.2 Accessories for 3UG4 monitoring relays Image 13-10 3UL2303-1A Image 13-11 3UL2304-1A 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 350
Accessories 13.2 Accessories for 3UG4 monitoring relays Image 13-12 3UL2305-1A Image 13-13 3UL2306-1A 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 351
Accessories 13.2 Accessories for 3UG4 monitoring relays Image 13-14 3UL2307-1A 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 352: Accessories For 3Ug458. Insulation Monitoring Relays
The sealable cover can be used to secure the actuators (rotary buttons and sliding switches) of the monitoring relays against unauthorized or unintentional manipulation. Siemens also offers a sealable membrane (3TK2820-0AA00) with a width of 22.5 mm for securing the monitoring relays. The sealable membrane is affixed to the front of the device and secures rotary buttons and sliding switches against unintentional operation.
-
Page 353: 3Ug4983 Upstream Module For The 3Ug4583 Monitoring Relay
Connection to 3UG4583 terminal VS Connection to 3UG4583 terminal Measuring signal input, ground connection Connection to 3UG4583 terminal L+ Connection to 3UG4583 terminal L- Connection to 3UG4583 terminal V1+ Connection to 3UG4583 terminal V1- 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 354
1 / 2 To remove, apply the screwdriver to the device and push it up with a twisting motion against the tension of the fixing spring. Swing the device upwards to remove it. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 355: Internal Circuit Diagrams
Accessories 13.3 Accessories for 3UG458. insulation monitoring relays. 13.3.2.1 Internal circuit diagrams Internal circuit diagram 3UG983-1A 3UG4983-1A Image 13-15 3UG4983-1A insulation monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 356
2-wire AC system / 2-wire DC system 2-wire AC system 2-wire DC system 3-wire AC system / 3-wire DC system 3-wire AC system 3-wire DC system 4-wire AC system 4-wire AC system 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 357
The maximum cable length between the 3UG4583 insulation monitoring relay and the 3UG4983 upstream module is 0.4 m. Note The maximum cable length of the measuring circuit connections is 50 m or 100 pF/m. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 358: Technical Data
Distance, to be maintained, to the ranks assembly forwards • backwards • sidewards • upwards • downwards • Distance, to be maintained, conductive elements forwards • backwards • sidewards • upwards • downwards • 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 359
AWG number as coded connectable conductor cross section 20 … 12 solid • 18 … 14 stranded • Tightening torque N·m 0.6 … 0.8 with screw-type terminals • Number of change-over switches delayed switching 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 360
Accessories 13.3 Accessories for 3UG458. insulation monitoring relays. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 361: References
References Further references You will find further information on the 3RR2 and 3UG4 monitoring relays on the Internet (http://support.automation.siemens.com/WW/view/en/20356134/133300). In addition to this manual, please refer to the operating instructions and manuals for any accessories. You can download the relevant documentation from the Internet (http://www.siemens.com/sirius/manuals).
-
Page 362
3ZX1012-0UG46-4BA1 monitoring (3UG4641) SIRIUS monitoring relay for speed monitoring (3UG4651) 3ZX1012-0UG46-5BA1 Manuals Title Reference Functional safety — Use of SIRIUS 3UG4 and 3RR2 monitoring relays Internet with integrated sensors (http://support.automation.si emens.com/WW/view/en/39 863898) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 363: Parameters
(terminal C/Q) is switched in SIO mode. If the threshold has been reached, the output relays are switched accordingly and an IO-Link message may be sent. Possible indications on the display: Asy (threshold), possibly Asy! (warning threshold) 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 364
(zero current). ● At manual reset A fault is acknowledged by a manual reset. Following this, the device behaves in the same way as when the supply voltage is switched on again. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 365
After exiting the menu level SET, the ON-delay time starts again. Start of the ON-delay The following table shows the behavior of the ON-delay time (onDel) with the device variants 3UG4 monitoring relay and 3RR2 current monitoring relay. Device variants Start of the ON-delay possible for: «Power-ON»… -
Page 366
● Level undershoot: Yellow LED lights up as soon as the output relay picks up, depending on the functional principle selected ● Insulation resistance undershoot: Red LED lights up continuously ● Voltage undershoot: Red LED lights up continuously 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 367
● Manual RESET If manual RESET is selected, the switching contact remains in the current switching state even if the measured value returns to a permissible value. Possible indications on the display: Mem 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 368
For this reason, the output relays are switched to the work position when the supply voltage is present. After completion of the initialization phase, a permanent self-test takes place without interrupting the monitoring function. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 369
If phase sequence monitoring has been activated and the load currents exhibit the wrong phase sequence, the CO contact and the semiconductor output will change their switching status immediately (≤ 200 ms). Possible indications on the display: 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 370
You can determine the thresholds by operating the motor at the load limits, for example. You can then read the thresholds as the up-to-date measured values off the display of the monitoring relay. 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 371
Unlike with pure reconnection at the CO contact output, with use of the relay switching behavior parameter, it is possible to prevent unwanted pumping in the absence of a supply voltage. Possible indications on the display: ● Closed-circuit principle: NC ● Open-circuit principle: NO 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 372
The «scaling factor» parameter allows the user to set the number of pulses per revolution provided by the pulse encoder. This allows the revolutions per minute to be read direct on the display. Possible indications on the display: Scale 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 373
Set delay times have no effect on phase failure monitoring. The «phase failure monitoring» parameter on the 3UG48 monitoring relays is set either locally via the three keys on the device, or via IO-Link. Possible indications on the display: 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 374
Parameters 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 375: Dimension Drawings
Dimension Drawings Dimension drawings 3RR2 monitoring relay 3RR2.41-1A.30 (screw connection, S00) Image C-1 3RR2.41-1A.30 with contactor Image C-2 33RR2.41-1A.30 with terminal support for stand-alone assembly 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 376
Dimension Drawings C.1 Dimension drawings 3RR2 monitoring relay 3RR2.41-2A.30 (spring-loaded connection, S00) Image C-3 3RR2.41-2A.30 with contactor Image C-4 3RR2.41-2A.30 with terminal support for stand-alone assembly 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 377
Dimension Drawings C.1 Dimension drawings 3RR2 monitoring relay 3RR2.42-1A.30 (screw connection, S0) Image C-5 3RR2.42-1A.30 with contactor Image C-6 3RR2.42-1A.30 with terminal support for stand-alone assembly 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 378
Dimension Drawings C.1 Dimension drawings 3RR2 monitoring relay 3RR2.42-2A.30 (spring-loaded connection, S0) Image C-7 3RR2.42-2A.30 with contactor Image C-8 3RR2.42-2A.30 with terminal support for stand-alone assembly 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 379
Dimension Drawings C.1 Dimension drawings 3RR2 monitoring relay 3RR2143-1A.30 (S2) Image C-9 3RR2143-1A.30 with contactor Image C-10 3RR2143-1A.30 with terminal support for stand-alone assembly 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 380
Dimension Drawings C.1 Dimension drawings 3RR2 monitoring relay 3RR2143-3A.30 (S2) Image C-11 3RR2143-3A.30 with contactor Image C-12 3RR2143-3A.30 with terminal support for stand-alone assembly 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 381
Dimension Drawings C.1 Dimension drawings 3RR2 monitoring relay 3RR2243-1F.30 (S2) Image C-13 3RR2243-1F.30 with contactor Image C-14 3RR2243-1F.30 with terminal support for stand-alone assembly 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 382
Dimension Drawings C.1 Dimension drawings 3RR2 monitoring relay 3RR2243-3F.30 (S2) Image C-15 3RR2243-3F.30 with contactor Image C-16 3RR2243-3F.30 with terminal support for stand-alone assembly 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 383: Dimension Drawings 3Ug4 Monitoring Relays
Dimension drawings 3UG4 monitoring relays. (2 connecting terminals) 3UG4. monitoring relays with 2 connecting terminals (screw-type connection) Image C-17 3UG4. monitoring relays with 2 connecting terminals with screw-type connections 3UG4. monitoring relays with 2 connecting terminals (spring-loaded connections) Image C-18 3UG4. monitoring relays with 2 connecting terminals with spring-loaded connections…
-
Page 384: Dimension Drawings 3Ug4 Monitoring Relays. (3 Connecting Terminals)
Dimension drawings 3UG4 monitoring relays. (3 connecting terminals) 3UG4. monitoring relays with 3 connecting terminals (screw-type connection) Image C-19 3UG4. monitoring relays with 3 connecting terminals with screw-type connections 3UG4. monitoring relays with 3 connecting terminals (spring-loaded connections) Image C-20 3UG4. monitoring relays with 3 connecting terminals with spring-loaded connections…
-
Page 385: Dimension Drawings 3Ug4 Monitoring Relays. (4 Connecting Terminals)
C.2 Dimension drawings 3UG4 monitoring relays C.2.3 Dimension drawings 3UG4 monitoring relays. (4 connecting terminals) 3UG4. monitoring relays with 4 connecting terminals (screw-type connection) Image C-21 3UG4. monitoring relays with 4 connecting terminals with screw-type connections 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 386
Dimension Drawings C.2 Dimension drawings 3UG4 monitoring relays 3UG4. monitoring relays with 4 connecting terminals (spring-loaded connections) Image C-22 3UG4. monitoring relays with 4 connecting terminals with spring-loaded connections 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 387: Dimension Drawings 3Ug458 Insulation Monitoring Relay. (3Ug4983 Upstream Module)
Dimension Drawings C.2 Dimension drawings 3UG4 monitoring relays C.2.4 Dimension drawings 3UG458 insulation monitoring relay. (3UG4983 upstream module) 3UG4581-1AW30/3UG4582-1AW30 monitoring relays Image C-23 3UG4581-1AW30/3UG4582-1AW30 insulation monitoring relays 3UG4583-1CW30 monitoring relay Image C-24 3UG4583-1CW30 insulation monitoring relay 3UG4 / 3RR2 monitoring relays…
-
Page 388
Dimension Drawings C.2 Dimension drawings 3UG4 monitoring relays 3UG4983-1A upstream module Image C-25 3UG4983-1A upstream module 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 389: Menu-Based Operation
Menu-based operation 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004…
-
Page 390
Menu-based operation 3RR2241 current monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 391
Menu-based operation 3RR2242 current monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 392
Menu-based operation 3RR2243 current monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 393
Menu-based operation 3UG4614 line monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 394
Menu-based operation 3UG4615 line monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 395
Menu-based operation 3UG4616 line monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 396
Menu-based operation 3UG4617 line monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 397
Menu-based operation 3UG4618 line monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 398
Menu-based operation 3UG4621 current monitoring relays 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 399
Menu-based operation 3UG4622 current monitoring relays 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 400
Menu-based operation 3UG4624 residual current monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 401
Menu-based operation 3UG4625 residual current monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 402
Menu-based operation 3UG4631 voltage monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 403
Menu-based operation 3UG4632 voltage monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 404
Menu-based operation 3UG4633 voltage monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 405
Menu-based operation 3UG4641 cos phi and active current monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 406
Menu-based operation 3UG4651 speed monitoring relay 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 407: Index
Apparent current, 370 3UG4582-1AW30, 256 Application areas 3UG4583-1CW30, 258 3RR2 current monitoring relays, 47 3UG4583-1CW30 and 3UG4983-1A, 356 3UG4.1 line monitoring relay, 102 2-wire DC system 3UG4501 filling level monitoring relay, 89 3UG4582-1AW30, 256 3UG4581/3UG4582/3UG4583 insulation monitoring 3UG4583-1CW30, 258 relays, 215…
-
Page 408
Inflow control, 95, 371 3UG4511 line monitoring relay, 103 Installation 3UG4512 line monitoring relay, 111 Mounting rail, 3UG4983 upstream module, 354 3UG4513 line monitoring relay, 121 Installation altitude, 20 3UG4581 insulation monitoring relay, 218 3UG4 / 3RR2 monitoring relays Manual, 05/2016, NEB927043002000/RS-AC/004… -
Page 409
296 Screw mounting, 3RR2 current monitoring relay, 30 3UG4651 speed monitoring relay, 312 Current monitoring relay 3RR22, digital, 75 Screw mounting, 3UG4 monitoring relay, 34 Standard rail, 3UG4 monitoring relay, 34 Phase asymmetry Mounting position, 34 3UG4.1 line monitoring relay, 101, 102 3RR2 current monitoring relays, 29 3UG4.1 line monitoring relay, 101, 102… -
Page 410
3UG4641 cos phi and active current monitoring Screw mounting relay, 289 3UG4 monitoring relay, 34 Undervoltage Screw-type connection, 22 3UG4.1 line monitoring relay, 101, 102 Screw-type connection system 3UG4.1 line monitoring relay, 101, 102 Connection cross-sections, 21 3UG4631/3UG4632/3UG4633 voltage monitoring Screw-type connections, 21…
Перейти к содержанию
На чтение 3 мин Просмотров 3 Опубликовано 30 декабря, 2021
3UG4616-1CR20
3UG4616-1CR20 — реле контроля Siemens
Технические характеристики 3UG4616-1CR20: Реле 3-х фазного с n напряжения контроль реверсируемого чередования фаз и выпадения фазы 3x 160 до 690 вольт, ac 50 до 60 герц, падение и превышение напряжения 160-690 вольт, гистерезис 1-20 вольт, каждый 0-20 s для umin и umax 1 w для rpm 1 w для umax винтовое подсоединение, замена для 3ug3042-1bp50
Техническая документация для 3UG4616-1CR20
Документация для 3UG (2Мб)
Таблица международной классификации степеней защиты
Составляющая обозначения | Класс/степень защиты | |
Первая цифра защита от проникновения твердых частиц |
0 | нет защиты |
1 | Защита от проникновения твердых частиц размером не менее 50 мм (случайное касание рукой) | |
2 | Защита от проникновения твердых частиц размером не менее 12 мм (палец руки) | |
3 | Защита от проникновения твердых частиц размером не менее 2,5 мм (инструменты, кабели) | |
4 | Защита от проникновения твердых частиц размером не менее 1 мм (тонкие инструменты, провод) | |
5 | Защита от проникновения пыли в количествах, не влияющих на работоспособность изделия | |
6 | Полная защита от проникновения пыли | |
Вторая цифра защита от проникновения жидкостей |
0 | нет защиты |
1 | Защита от вертикально падающих капель воды (конденсат) | |
2 | Защита от капель воды, падающих под углом не более 15° от вертикали | |
3 | Защита от капель дождя, падающих под углом не более 60° от вертикали | |
4 | Защита от брызг воды со всех направлений | |
5 | Защита от струй воды со всех направлений | |
6 | Защита от воздействия воды, идентичного морским волнам | |
7 | Защита от проникновения воды при погружении на глубину до 1 м | |
8 | Защита от проникновения воды при длительном погружении под давлением | |
Третья цифра защита от механических повреждений |
0 | нет защиты |
1 | Энергия удара 0,225 Дж (груз 150 г, с высоты 15 см) | |
3 | Энергия удара 0,5 Дж (груз 250 г, с высоты 20 см) | |
5 | Энергия удара 2 Дж (груз 500 г, с высоты 40 см) | |
7 | Энергия удара 6 Дж (груз 1,5 кг, с высоты 40 см) |
- Мы авторизованный дистрибьютор Siemens
- У нас большой склад с постоянно пополняемой номенклатурой
- Скидки для постоянных клиентов
- Доставка по России
- Профессиональные консультации и техническая поддержка
- Минимальные сроки поставки для заказного оборудования
Качество плавких предохранителей основывается на компетентной разработке изделий, тщательном выборе и контроле применяемых заготовок и монтаже. То есть одно скрыто внутри и недоступно взгляду пользователя.
Возможные неточности и опечатки не могут являться основанием для претензий, в т.ч. юридического характера. Техническую и коммерческую информацию о поставляемых товарах необходимо уточнять у специалистов отдела продаж нашей компании. Для связи пользуйтесь формой обратной связи, факсом, телефоном или электронной почтой.
Источник
Цена распродажи
22371.00 ₽*
Цена розничная
25727.00 ₽
* Цена действительна при условии выставления счёта от организации, работающей на УСН.
Внимание! Актуальные цены будут указаны в выставленном счете или КП.
Условия доставки
Доставка заказа от 250 рублей*
*Весом до 1 кг, до пункта выдачи курьерской службы в г. Москва
- Доставка по всей России до двери или в пункт выдачи
- Ежедневная отправка заказов курьерскими службами
- Бесплатная доставка до терминалов ТК два раза в неделю
- Самовывоза нет
- Документы
3UG4616-1CR20
Аналогичные изображения РЕЛЕ КОНТРОЛЯ ЧЕРЕДОВАНИЯ ФАЗ ДЛЯ 3-Ф. С N-ПРОВОДНИКОМ, 3X 160 ДО 690 В AC 50 ДО 60 ГЦ, ВЫПАДЕНИЯ ФАЗЫ И N-ПРОВОДНИКА, ПАДЕНИЯ И ПРЕВЫШЕНИЯ НАПРЯЖЕНИЯ 160-690 В, ГИСТЕРЕЗИС 1-20 В, ЗАДЕРЖКА СРАБАТЫВАНИЯ 0-20 С., ДЛЯ UMIN И UMAX 1 W ДЛЯ RPM 1 W ДЛЯ UMAX, ВИНТОВЫЕ КЛЕММЫ
|
| |
3UG4616-1CR20
3UG4616-1CR20 — реле контроля Siemens
Технические характеристики 3UG4616-1CR20: Реле 3-х фазного с n напряжения контроль реверсируемого чередования фаз и выпадения фазы 3x 160 до 690 вольт, ac 50 до 60 герц, падение и превышение напряжения 160-690 вольт, гистерезис 1-20 вольт, каждый 0-20 s для umin и umax 1 w для rpm 1 w для umax винтовое подсоединение, замена для 3ug3042-1bp50
Техническая документация для 3UG4616-1CR20
Документация для 3UG (2Мб)
Таблица международной классификации степеней защиты
Составляющая обозначения | Класс/степень защиты | |
Первая цифра защита от проникновения твердых частиц |
0 | нет защиты |
1 | Защита от проникновения твердых частиц размером не менее 50 мм (случайное касание рукой) | |
2 | Защита от проникновения твердых частиц размером не менее 12 мм (палец руки) | |
3 | Защита от проникновения твердых частиц размером не менее 2,5 мм (инструменты, кабели) | |
4 | Защита от проникновения твердых частиц размером не менее 1 мм (тонкие инструменты, провод) | |
5 | Защита от проникновения пыли в количествах, не влияющих на работоспособность изделия | |
6 | Полная защита от проникновения пыли | |
Вторая цифра защита от проникновения жидкостей |
0 | нет защиты |
1 | Защита от вертикально падающих капель воды (конденсат) | |
2 | Защита от капель воды, падающих под углом не более 15° от вертикали | |
3 | Защита от капель дождя, падающих под углом не более 60° от вертикали | |
4 | Защита от брызг воды со всех направлений | |
5 | Защита от струй воды со всех направлений | |
6 | Защита от воздействия воды, идентичного морским волнам | |
7 | Защита от проникновения воды при погружении на глубину до 1 м | |
8 | Защита от проникновения воды при длительном погружении под давлением | |
Третья цифра защита от механических повреждений |
0 | нет защиты |
1 | Энергия удара 0,225 Дж (груз 150 г, с высоты 15 см) | |
3 | Энергия удара 0,5 Дж (груз 250 г, с высоты 20 см) | |
5 | Энергия удара 2 Дж (груз 500 г, с высоты 40 см) | |
7 | Энергия удара 6 Дж (груз 1,5 кг, с высоты 40 см) |
- Мы авторизованный дистрибьютор Siemens
- У нас большой склад с постоянно пополняемой номенклатурой
- Скидки для постоянных клиентов
- Доставка по России
- Профессиональные консультации и техническая поддержка
- Минимальные сроки поставки для заказного оборудования
Качество плавких предохранителей основывается на компетентной разработке изделий, тщательном выборе и контроле применяемых заготовок и монтаже. То есть одно скрыто внутри и недоступно взгляду пользователя.
Возможные неточности и опечатки не могут являться основанием для претензий, в т.ч. юридического характера. Техническую и коммерческую информацию о поставляемых товарах необходимо уточнять у специалистов отдела продаж нашей компании. Для связи пользуйтесь формой обратной связи, факсом, телефоном или электронной почтой.
Источник
SIRIUS
Überwachungsrelais
Monitoring Relays
Relais de surveillance
Relé de vigilancia
para redes de tensión trifásica
Relé di sorveglianza
Relé de monitoramento
Betriebsanleitung
Operating Instructions
Instructivo
Istruzioni operative
Vor der Installation, dem Betrieb oder der Wartung des Geräts muss diese Anleitung gelesen und verstanden werden.
Read and understand these instructions before installing, operating, or maintaining the equipment.
Ne pas installer, utiliser ou intervenir sur cet équipement avant d’avoir lu et assimilé les présentes instructions et notamment les conseils de sécurité
et mises en garde qui y figurent.
Leer y comprender este instructivo antes de la instalación, operación o mantenimiento del equipo.
Leggere con attenzione queste istruzioni prima di installare, utilizzare o eseguire manutenzione su questa apparecchiatura.
Ler e compreender estas instruções antes da instalação, operação ou manutenção do equipamento.
GEFAHR
!
Gefährliche Spannung.
Lebensgefahr oder schwere Verletzungs-
gefahr.
Vor Beginn der Arbeiten Anlage und
Gerät spannungsfrei schalten.
PELIGRO
!
Tensión peligrosa.
Puede causar la muerte o lesiones
graves.
Desconectar la alimentación eléctrica
antes de trabajar en el equipo.
Eine sichere Gerätefunktion ist nur mit zertifizierten Komponenten gewährleistet!
Reliable functioning of the equipment is only ensured with certified components.
La sécurité de fonctionnement de l’appareil n’est garantie qu’avec des composants certifiés.
El funcionamiento seguro del aparato sólo está garantizado con componentes certificados.
Il funzionamento sicuro dell’apparecchiatura è garantito soltanto con componenti certificati.
O funcionamento seguro do aparelho apenas pode ser garantido se forem utilizados os componentes certificados.
1. U = 0 V
2. a, b, c, d
b
a
b
GWA 4NEB 927 0413-10 DS 01
zur dreiphasigen Netzüberwachung
for Three-Phase Voltage Monitoring
de tension triphasée
per un controllo di tensione trifase
para supervisão de tensão trifásica
Instructions de service
Instruções de Serviço
Hazardous voltage.
Will cause death or serious injury.
Turn off and lock out all power supplying this
device before working on this device.
Tensione pericolosa.
Può provocare morte o lesioni gravi.
Scollegare l’alimentazione prima di
eseguire interventi sull’apparecchiatura.
3RP1903
c
d
DANGER
!
PERICOLO
!
C
B
A
A, B, C
Kodiert
Coded
Codé
Cifrado
Codificato
Codificado
3UG4616-1BR28-0AA1
EN 60 947, IEC 60 947
Bestell-Nr./Order No.: 3ZX1012-0UG46-1BA1
DANGER
!
Tension électrique.
Danger de mort ou risque de blessures
graves.
Mettre hors tension avant d’intervenir sur
l’appareil.
PERIGO
!
Tensão perigosa.
Perigo de morte ou ferimentos graves.
Desligue a corrente antes de trabalhar no
equipamento.
3
4
1
2
3RP1902
Last update: 07 May 2007
4
5
Цена распродажи
14827.00 ₽*
Цена розничная
17051.00 ₽
* Цена действительна при условии выставления счёта от организации, работающей на УСН.
Внимание! Актуальные цены будут указаны в выставленном счете или КП.
Условия доставки
Доставка заказа от 250 рублей*
*Весом до 1 кг, до пункта выдачи курьерской службы в г. Москва
- Доставка по всей России до двери или в пункт выдачи
- Ежедневная отправка заказов курьерскими службами
- Бесплатная доставка до терминалов ТК два раза в неделю
- Самовывоза нет
- Документы
3UG4616-1CR20
Аналогичные изображения РЕЛЕ КОНТРОЛЯ ЧЕРЕДОВАНИЯ ФАЗ ДЛЯ 3-Ф. С N-ПРОВОДНИКОМ, 3X 160 ДО 690 В AC 50 ДО 60 ГЦ, ВЫПАДЕНИЯ ФАЗЫ И N-ПРОВОДНИКА, ПАДЕНИЯ И ПРЕВЫШЕНИЯ НАПРЯЖЕНИЯ 160-690 В, ГИСТЕРЕЗИС 1-20 В, ЗАДЕРЖКА СРАБАТЫВАНИЯ 0-20 С., ДЛЯ UMIN И UMAX 1 W ДЛЯ RPM 1 W ДЛЯ UMAX, ВИНТОВЫЕ КЛЕММЫ
|
| |
3UG4616-1CR20
Наименование | Краткое описание | Карточка товара |
||
---|---|---|---|---|
3UG4616-1CR20 (SIEMENS) | — |
Представленные в документации товары
Скачать документацию: Документация на 3UG4616-1CR20 (277.6 Кб)