Valco baby snap 4 инструкция по сборке

PRODUCT REFERENCE GUIDE
SNAP &
SNAP4
Stroller
© Copyright
VE 2012
vs220113USA
FURTHER INFORMATION:
In North America only
www.valcobaby.com
1800 610 7850
Find us on:
SNAP &
SNAP4
Stroller
Thank you for purchasing a quality
VALCO BABY product.
Please read and follow the instructions outlined in
this guide carefully. Familiarise yourself with the
construction and safety features; be sure that you
understand all the warnings and safety
guidelines before use.
Important: Please read the following
instructions carefully before assembling this
product. Retain this guide in a safe place for
future reference.
DISCLAIMER
Due to our policy of continuous product development,
this product is constantly evolving. It is possible that
some features or procedures outlined here have
changed since this document was written. If you are
unsure of any procedure shown here, please contact
us via the web at [email protected] to obtain the
most up to date information before use. Include the
batch number and model number, which can be found
on a sticker on the frame.
All pictures and diagrams herein are provided for illustration
purposes only. Actual product, colour or fabric may vary.
VALCO BABY reserves the right to modify or alter any
specification or colour without notice or obligation to
modify any product previously purchased
1>PARTS LIST
SNAP
SNAP 4
BUMPER
BAR
1x FRONT DUAL
WHEEL
2x FRONT
WHEELS
STROLLER FRAME,
SEAT & HOOD UNIT
REAR AXLE
REAR WHEELS x 2
1x FRONT
WHEEL SHAFT
2>TO OPEN
a
4>REAR WHEELS & BRAKE
3>REAR AXLE
a
a
a
5>FRONT WHEELS
d
b
c
Housing
notch
Shaft
lock
a
FOR SNAP ONLY
FOR SNAP AND
SNAP 4
e
f
g
6>TO FOLD
b
d
c
a
7>BUMPER BAR
a
8>SEAT RECLINE
l
a
SQUEEZE
PULL
9>HARNESS
c
b
CLICK
a
d
e
PRESS
DOWN
HOLD
DOWN
f
RELEASE
HOLD
PUSH
10>HOOD
CLICK
a
b
11>TETHER STRAP
a
INSTRUCTIONS
1>PARTS LIST
Stroller frame with hood attached, 2x rear
wheels, 1x front dual swivel wheel & front
wheel shaft (Snap) or 2x front swivel wheels
with shaft attached (Snap 4), 1x bumper bar.
2>TO OPEN
Release the frame lock (a) by pulling it clear
of the locking pin.
Lift the handle in one continuous motion while
allowing the legs to simultaneously open.
Continue until the frame locks fully open.
IMPORTANT WARNING: ALWAYS TEST
THAT ALL LATCHES ARE SECURELY
ENGAGED BEFORE USE.
3>REAR BRAKE AXLE
Align the rear axle housing with the rear
stroller legs. Insert each rear leg into the
corresponding housing of the rear axle.
Press in the locking button (a) on the leg
while simultaneously pushing the axle
housing as far as it will go until it engages.
Repeat for the other leg.
Test that each leg has fully engaged in the
axle housing.
4>REAR WHEELS & BRAKE
While depressing the button (a) at the rear
axle junction, insert the rear wheel axle into
the rear axle tube of the stroller. Push the
axle into the tube as far as it will go before
releasing the button.
Repeat for other wheel.
To release your wheel, press button (b) and
pull from axle tube.
IMPORTANT: Test that each wheel
has FULLY engaged in the frame
tube before use by pulling on it.
To use the rear brakes:
Press down on the right side of the red
brake lever located on the rear axle to
simultaneously engage the brake in both
rear wheels.
To release, press down on the left side of the
red brack lever with your foot.
IMPORTANT WARNING: ALWAYS TEST
THAT THE BRAKES ARE SECURELY
DISENGAGED BEFORE USE.
5>FRONT WHEELS
FOR SNAP ONLY:
Install the front wheel shaft to the stroller
first: align the front wheel shaft (a) with
the front wheel housing (b) taking care to
orientate the shaft lock with the notch found
on the rear of the wheel housing. Insert the
front wheel shaft into the housing until it is
engaged.
Align the front wheel with the shaft and
slip the wheel onto the shaft. Note that the
locking tab should be positioned to the
front. Insert the wheel over the shaft untill
it is engaged.
FOR SNAP AND SNAP4: Align each front
wheel pin (a) beneath the housing (b) on
each front leg of the stroller. Be sure that the
pin engages securely in the channel
IMPORTANT: ALWAYS TEST THAT ALL
LATCHES ARE SECURELY ENGAGED AND
THE WHEEL HAS SECURELY ENGAGED IN
THE CHANNEL BEFORE USE.
To fix the front wheel(s) in the non-swivel
position: Turn the wheel so that the notch at
the front of the wheel channel (c) lines up
with the one in the top plastic housing (d).
Press down firmly on the tab until it locks
into place.
6>TO FOLD
Press down on the secondary lock button
(a) - it will stay down. Squeeze the fold
button in the handle (b), moving the handle
forward slightly.
Grasp the folding handle (c) allowing the
handle to move all the way forward till the
frame automatically locks shut (d).
Your SNAP stroller can stand unaided for
easy storage.
HINT: WHILE NOT NECESSARY FOR
FOLDING, MOVING THE SEAT BACK
FIRST TO THE MOST UPRIGHT POSITION
AND FORWARD THROUGH THE FRAME
WILL MAKE FOR THE MOST SIMPLE AND
COMPACT FOLDING.
Note: Your Snap stroller also comes
equipped with a handy shoulder strap for
easy carrying.
7>BUMPER BAR
Insert each side of the bumper bar fitting
into the corresponding housing in the seat
frame until you hear it click into place.
The bumper bar can be opened as a “gate”
for easy access pressing on one of the
release buttons (a) and lifting the side out
of the housing. For full removal, repeat this
process for the other side.
8>SEAT RECLINE
To recline: While squeezing the seat adjuster
tabs (a) together in a pincer like movement,
ease the seat down to the desired
position. Release the tabs and the seat will
automatically lock in that position
To incline: Place your hand in the centre of
the seat at the rear. Pull the incline strap (b)
while gently pushing the seat upward to the
desired position.
9>HARNESS
To secure your child in the harness:
Overlap buckles and so that they fit together
to form one complete buckle (a).
Insert the completed buckle into the Buckle
Housing (b) until it engages securely in
place(c).
To open your harness:
Push down on both Buckle Prongs (d).
Simultaneously press the release button in
the centre of the buckle (e).
Lift the buckles from the Buckle Housing (f).
IMPORTANT WARNING:
avoid serious injury from falling
or sliding out. always use seat belt.
10>EXPANDA HOOD
Your SNAP hood is designed to provide
maximum shade and comfort for your child
by incorporating our EXPANDA HOOD
section.
To increase/decrease the hood size
Open the EXPANDA HOOD section fully
using the zip (a).
Gently pull your hood forward; extending it
as far as is required.
When no longer needed, fold the EXPANDA
HOOD backward, allowing it to fold in on
itself.
Gently zip the section closed being mindful
not to catch any of the fabric in the zipper
teeth.
Additional ventilation can be achieved by
rolling up the rear of the hood like a blind
and securing in the open position with the
toggle (b).
11>TETHER STRAP
Your SNAP stroller is fitted with a handy
tether strap which helps keep your stroller
always within reach. Slip the tether cuff (a)
over your wrist and use the stroller normally.
IMPORTANT: ALWAYS USE THE TETHER
STRAP WHEN A CHILD IS IN THE STROLLER
WARNING: To avoid injury or death
• always apply the brakes whenever the pram/stroller is stationary
• DO NOT LEAVE CHILDREN UNATTENDED.
• DO NOT CARRY EXTRA CHILDREN OR BAGS ON THIS PRAM/STROLLER.
• MAKE SURE CHILDREN ARE CLEAR OF ANY MOVING PARTS IF YOU ADJUST THE PRAM/STROLLER.
OTHERWISE THEY MAY BE INJURED.
! warning: use this harness at all times.
! warning: when not in use disconnect shoulder straps from the waist strap and/or
buckle.
• FOLLOW THE MANUFACTURER’S INSTRUCTIONS.
Remember, your child’s safety is your responsibility...
• NEVER USE ON stairs or ESCALATORS.
• Always use the tether strap when the stroller is in use.
• THE CORRECT USE AND MAINTENANCE OF THIS VEHICLE ARE ESSENTIAL.
• Be sure that all clamps and buckles are securely fixed and in place before use
! ALWAYS use the harness, correctly fitted and adjusted, with your child in this seat.
• The maximum weight of the child for which this stroller was intended is 20kgs (44lbs)..
• The maximum height of the child for which this stroller was intended is 90cm (35inches).
• the stroller will become unstable if the manufacturer’s recommended load is exceeded.
• care must be taken when folding and unfolding the product to prevent finger
entrapment.
• Can be used from a newborn baby onwards. A cocoon, specially designed to be used
with a stroller, is recommended when any fully reclining stroller is used with a
newborn.
• Never run with a newborn baby in any pram or stroller until the child can sit up
unassisted (approximately 6 months).
• CHECK ALL PARTS BEFORE USE FOR BREAKAGE OR FATIGUE. DISCONTINUE USE IMMEDIATELY IF ANY
PART IS FOUND TO BE DAMAGED OR BROKEN.
• MAXIMUM LOAD OF BASKETS: 5KGS (11LBS).
• Do not carry additional children.
THIS STROLLER IS MANUFACTURED FOR USE WITH ONE CHILD ONLY
• ALWAYS be aware of the risks provided by fire and other significant sources of heat such
as radiators, etc. which may be in the immediate vicinity of your stroller.
• It may be unsafe to use any accessories other than VALCO baby approved ones.
• This product is intended for domestic use only. It is not intended for commercial use.
Should the chassis become wet, dry off promptly before storing. If this pram is used near the ocean or salted roads, spray the
chassis and seat frame with water and dry. We recommend a rust inhibiting product should be used to prevent rust and fatigue on
metal parts.
We recommend that you wipe down axles and lubricate the wheels every 3 months. Sand and dirt can grind down axles, if you live
near the beach or in a dusty environment you must wipe down the axles and wheels then lubricate them monthly.
AXLES ARE BEST LUBRICATED WITH GREASE OR PETROLEUM JELLY. MOVING PARTS ARE BEST LUBRICATED WITH SILICONE BASED
PRODUCTS. DO NOT USE OIL BASED PRODUCTS.
FURTHER INFORMATION:
In North America only
www.valcobaby.com
1800 610 7850
[email protected]
Find us on:

Was this manual useful for you?

Yes

No

Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project