Xenox sgx аппарат для маникюра инструкция по применению

XENOX — немецкий производитель аппаратов для педикюра и маникюра, выпускается фирмой PROXXON (Германия), которая в течении тридцати с лишним лет выпускает высокоточный электроинструмент.Серия XENOX создана на базе профессионального инструмента, использующегося в машиностроении, модельном и ювелирном производстве.

Аппараты для аппаратного маникюра и педикюра

новая версия сайта ВНИМАНИЕ! ЭТО СТАРАЯ ВЕРСИЯ САЙТА новый сайт: paradox-nails.ru  null

67000 Xenox Dent Аппарат с бесколлекторным двигателем бормашины — контролирует обороты, крутящий момент, обеспечивает безопасность при ошибках (заблокированный мотор, перегрузка). Цифровой дисплей с индикацией выставленной скорости вращения и кода ошибки. Если при использовании педали обороты в течение 3 секунд не изменяются, раздается звуковой сигнал. После этого обороты остаются постоянными даже если педаль отпущена. Для отключения функции необходимо нажать на педаль еще раз. Скорость вращения: до 50 000 об/мин Мощность: 230 Вт Вес: около 3 кг СПЕЦИАЛЬНОЕ ЦЕНОВОЕ ПРЕДЛОЖЕНИЕ! Действие акции ограничено. 42000 руб.

67 060 Xenox Nail 35K   Новинка. Скорость от 0 до 35000 об/мин. Мощность   65 Вт. Полуавтоматический зажим сменного инструмента с хвостовиком 2,35мм. Вес ручки — 180г, блока питания — 1450г. Плавность регулировки скорости, реверсивное вращение, практически бесшумная работа. —

№ 68 600 Базовый набор XENOX Компактный настольный прибор для аппаратного маникюра и педикюра. Вес бормашины MHX всего 230г, специальный захват позволяет держать её у самого инструмента. Электронная регулировка скорости от 5000 до 20000 об/мин. осуществляется регулятором на корпусе блока питания SGX. Напряжение питания 220в, 50/60 Гц, выходное напряжение 12в, мощность 40 Вт. Упакован в практичную сумку с коробочкой для фрез и щеточкой для их чистки. (бормашина без реверса)

№ 68 600R Базовый набор XENOX c реверсом Компактный настольный прибор для аппаратного маникюра и педикюра. Вес бормашины MHX всего 230г, специальный захват позволяет держать её у самого инструмента. Электронная регулировка скорости от 5000 до 20000 об/мин. осуществляется регулятором на корпусе блока питания SGX. Напряжение питания 220в, 50/60 Гц, выходное напряжение 12в, мощность 40 Вт. Упакован в практичную сумку с коробочкой для фрез и щеточкой для их чистки. (бормашина с реверсом)

№ 68 516 Переносной набор XENOX Включает в себя бормашину МНХ/Е с электронной регулировкой скорости от 5000 до 20000 об/мин. на корпусе машины, блок питания и 24 высококачественные насадки фирмы Meisinger для аппаратного маникюра и педикюра. Упакован в прочный пластиковый чемодан для переноски. Вес набора с чемоданом всего 1190 г. Напряжение питания 220 в, 50/60 Гц, выходное напряжение 12 в, мощность 40 Вт. (бормашина без реверса)

№ 68 516R Переносной набор XENOX Включает в себя бормашину МНХ/Е с электронной регулировкой скорости от 5000 до 20000 об/мин. на корпусе машины, блок питания и 24 высококачественные насадки фирмы Meisinger для аппаратного маникюра и педикюра. Упакован в прочный пластиковый чемодан для переноски. Вес набора с чемоданом всего 1190 г. Напряжение питания 220 в, 50/60 Гц, выходное напряжение 12 в, мощность 40 Вт. (бормашина с реверсом)

68 518 Переносной набор XENOX Включает в себя бормашину МНХ/Е с электронной регулировкой скорости от 5000 до 20000 об/мин. на корпусе машины, блок питания. Упакован в прочный пластиковый чемодан для переноски. Вес набора с чемоданом всего 1190 г. Напряжение питания 220 в, 50/60 Гц, выходное напряжение 12 в, мощность 40 Вт. (бормашина без реверса)

№ 68 518R Переносной набор XENOX То же, что и №68 516, но без насадок (бормашина с реверсом)

№ 68 500 ручка MNX XENOX Питание 12 в, скорость вращения 20000 об/мин, мощность 40 Вт. Вес 230 гр.. Используется в качестве дополнения к набору №68 600 (без реверса)

68 500 R ручка MNX XENOX с реверсом Питание 12 в, скорость вращения 20000 об/мин, мощность 40 Вт. Вес 230 гр.. Используется в качестве дополнения к набору №68 600, 68 600 R (с реверсом)

MicroSpeed 22000 — Кольцевое сопло и мощный (550 Вт!) двигатель пылесоса легко удаляют мельчайшую пыль. — Плавная регулировка скорости до 22000 об/мин. позволяет работать насадками самых различных диаметров — Автоматический зажим  — легкая замена насадок — Оснащен реверсом, регулятором скорости фрезы и мощности пылесоса — Алюминиевая ручка легко дезинфицируется null

Настольный пылесос Незаменим при аппаратном маникюре. Съемный мешок для пыли. null

Форум о маникюре и педикюре Задайте интересующий Вас вопрос на www.nailclub.ru null

Если цены указаны не в рублях, то они указаны в условных единицах. 1 у.е.= 1 евро с учетом НДС.
Оплата производится в рублях по курсу ЦБ РФ+2% на день оплаты.

XENOX Laboratory equipment

XENOX laboratory equipment are precision tools for dental laboratories, opticians, hearing aid acoustic technicians, design studios, jewellery and goldsmith workshops, electronics laboratories and manicure and pedicure institutes. Equipment in proven design for drilling, milling, grinding, polishing, brushing, cleaning, engraving and separating precious metals, ceramics, plastics, steel, glass, minerals and many other materials.

The assortment includes handheld equipment and a few just as useful table top tools and chuck tools. Our

XENOX tools are coordinated constructively thus forming a compatible system.

No. 68 600

XENOX complete set

consisting of XENOX SGX control unit and MHX motor handpiece.

XENOX SGX control unit

In a compact NORYL case. With a super capacity of 5.0 A at 16 V no-load voltage and 12 V operating voltage (60 W DC). Primary connection for 220 — 240 V. Thyristor-controlled electronics (full-wave electronics with feedback effect) for stable rotational speed and much torque in the lower range.

3 connection sockets for XENOX plugs. 1 universal connection for banana plugs (Ø 4 mm).

Master switch and LED indicator for operational readiness. PTC resistance against overload. Practical holes in the casing to insert the necessary insertion tools with 2.35 and 3 mm shafts. Folding storage rack.

XENOX MHX motor handpiece

With a mere diameter of 35 mm and weighing approx. 230 g, the unit is supremely manageable and the special motor makes it very smooth running and pleasantly quiet. The ground, ball-bearing spindle ensures vibration-free operation (no-load speed 20,000/min) and has a locking button to enable a change of tools. By utilising the high-quality 6-part steel collet chuck set (one of each: 1.0 — 1.5 — 2.0 — 2.4 —

3.0 — 3.2 mm), even the smallest shafts can be clamped absolutely centrically. The insertion tools will not clatter or pulsate. The ergonomically shaped aluminium grip area directly at the collet chuck gives you the necessary tactile sense for fine work. The rotational speed can be controlled from 5,000 —

20,000/min.

No. 68 704

XENOX SGX control unit

The safe power source for hand-operated XENOX precision tools with low-voltage safety voltage.

XENOX SGX control unit

In a compact NORYL case. With a super capacity of 5.0 A at 16 V no-load voltage and 12 V operating voltage (60 W DC). Primary connection for 220 — 240 V.

Thyristor-controlled electronics (full-wave electronics with feedback effect) for stable rotational speed and much torque in the lower range. 3 connection sockets for XENOX plugs. 1 universal connection for banana plugs (Ø 4 mm).

Master switch to switch off. Red LED indicator for operational readiness. PTC resistance against overload

(no automatic restarting of connected equipment. After cooling down, the mains plug must be briefly disconnected).

Practical holes in the casing to insert the necessary insertion tools with 2.35 and 3 mm shafts.

Folding storage rack.

No. 68 500

XENOX MHX motor handpiece

Supremely manageable. Vibration-free running thanks to the special motor and ball-bearing spindle a precision device.

XENOX MHX motor handpiece

With a mere diameter of 35 mm and weighing approx. 230 g, the unit is supremely manageable and the special motor makes it very smooth running and pleasantly quiet.

The ground, ball-bearing spindle ensures vibration-free operation (no-load speed 20,000/min) and has a locking button to enable a change of tools. By utilising the high-quality 6-part steel collet chuck set

(one of each: 1.0 — 1.5 — 2.0 — 2.4 — 3.0 — 3.2 mm), even the smallest shafts can be clamped absolutely centrically.

The insertion tools will not clatter or pulsate. The ergonomically shaped aluminium grip area directly at the collet chuck gives you the necessary tactile sense for fine work.

The device is operated with low-voltage safety voltage (12 V), 40 watt. We recommend our SGX control unit as power source. This controls the rotational speed from 5,000 — 20,000/min.

No. 68 510

XENOX MHX/E motor handpiece

Versatile motor handpiece with integrated control.

XENOX MHX/E motor handpiece

The MHX/E motor handpiece is the ideal device for grinding, milling, drilling, polishing and cleaning.

The ergonomically formed aluminium swivel nut in the grip area facilitates sensitive work.

The overall slim and light casing is perfect for freehand use. The powerful special motor with lowvoltage safety voltage (12 — 18 V, also enables wet grinding) runs quietly and has a long service life.

The device is connected to the 220 — 240 V mains supply via (1.0 A) transformer. The rotational speed can be infinitely controlled at the device from 5,000 — 20,000/min in a user-friendly manner.

The reception of the insertion tools is done by XENOX precision collect chucks (1 piece 2.4 mm included).

To exchange the tools, the precisely positioned shaft of the device can be locked at the push of a button.

No. 68 516

XENOX special set

for manicure and pedicure: MHX/E, 1.0 A transformer and 24 high-quality insertion tools in a practical plastic carrying case.

XENOX special set for manicure and pedicure

With 24 insertion tools in the accustomed top quality, this set belongs as part to the basic equipment for the manicure and pedicure sector.

The driving unit, our MHX/E motor handpiece, is the ideal device for grinding, milling, drilling, polishing and cleaning. The ergonomically formed aluminium swivel nut in the grip area facilitates sensitive work.

The overall slim and light casing is perfect for freehand use. The powerful special motor with lowvoltage safety voltage (12 — 18 V, also enables wet grinding) runs quietly and has a long service life.

The device is connected to the 220 — 240 V mains supply via (1.0 A) transformer. The rotational speed can be infinitely controlled at the device from 5,000 — 20,000/min in a user-friendly manner.

The reception of the insertion tools is done by XENOX precision collect chucks (1 each 1.0 — 1.5 — 2.0 —

2.4 — 3.0 — 3.2 mm included). To exchange the tools, the precisely positioned shaft of the device can be locked at the push of a button.

24 high-quality insertion tools are included in the set (shafts 44.0 x 2.35 mm).

No. 68 516

The insertion tools are available only as component parts of the XENOX special set.

007 016 029

Drills (rose-head bur)

2 pieces each 0.7 — 1.6 and 2.9 mm.

For work on nails.

For the treatment of corns.

009 014 023

Drills with cross-cut

2 pieces each 0.9 — 1.4 and 2.3 mm.

For work on nails.

For the treatment of corns.

010 018

Fissure burs with cross-cut

2 pieces each 1.0 and 1.8 mm.

For work along the nail fold.

Special bur

1 piece 10 mm.

For calluses and nails.

100

Special bur

1 piece 10 mm.

For calluses and nails.

100

Bur with cross-cut

1 piece 6 mm.

For calluses and nails.

060

Bur with cross-cut

(fine)

1 piece 6 mm.

For calluses and nails.

060

Elongated cavity cutter

1 piece 2.3 mm.

For the treatment of corns and calluses.

023

050 025

Carborundum grinding bits (pink)

1 piece each bullet (5 mm) and cone (2.5 mm).

For calluses and nails.

100

Special grinding bit

(white)

1 piece 10 mm.

For calluses and nails.

No. 68 518

XENOX special set

for manicure and pedicure: MHX/E, 1.0 A transformer including collet chucks (without insertion tools) in a practical plastic carrying case.

XENOX special set for manicure and pedicure

The driving unit, our MHX/E motor handpiece, is the ideal device for grinding, milling, drilling, polishing and cleaning. The ergonomically formed aluminium swivel nut in the grip area facilitates sensitive work.

The overall slim and light casing is perfect for freehand use. The powerful special motor with lowvoltage safety voltage (12 — 18 V, also enables wet grinding) runs quietly and has a long service life.

The device is connected to the 220 — 240 V mains supply via (1.0 A) transformer. The rotational speed can be infinitely controlled at the device from 5,000 — 20,000/min in a user-friendly manner.

The reception of the insertion tools is done by XENOX precision collect chucks (1 each 1.0 — 1.5 — 2.0 —

2.4 — 3.0 — 3.2 mm included). To exchange the tools, the precisely positioned shaft of the device can be locked at the push of a button.

The practical plastic carrying case offers room for insertion tools.

The ideal companion for mobile working use.

No. 68 502

XENOX Super-Set

consisting of XENOX SGX control unit, three XENOX

MHX motor handpieces and a practical device holder.

XENOX super set

Particularly functional configuration when it is necessary to exchange tools frequently. You can equip three devices with different insertion tools and save yourself the exchanging process between working operations. The secure Plexiglas holder makes sure the devices can be stored safely.

XENOX SGX control unit

In a compact NORYL case. With a super capacity of 5.0 A at 16 V no-load voltage and 12 V operating voltage (60 W DC). Primary connection for 220 — 240 V. Thyristor-controlled electronics (full-wave electronics with feedback effect) for stable rotational speed and much torque in the lower range.

3 connection sockets for XENOX plugs. 1 universal connection for banana plugs (Ø 4 mm). Master switch and LED indicator for operational readiness. PTC resistance against overload. Practical holes in the casing to insert the necessary insertion tools with 2.35 and 3 mm shafts. Folding storage rack.

XENOX MHX motor handpiece

With a mere diameter of 35 mm and weighing approx. 230 g, the unit is supremely manageable and the special motor makes it very smooth running and pleasantly quiet. The ground, ball-bearing spindle ensures vibration-free operation (no-load speed 20,000/min) and has a locking button to enable a change of tools. By utilising the high-quality 6-part steel collet chuck set (one of each: 1.0 — 1.5 — 2.0 — 2.4 — 3.0 —

3.2 mm), even the smallest shafts can be clamped absolutely centrically. The insertion tools will not clatter or pulsate. The ergonomically shaped aluminium grip area directly at the collet chuck gives you the necessary tactile sense for fine work. The rotational speed can be controlled from 5,000 — 20,000/min.

No. 67 100

XENOX KTX MICRO coordinates table

The KTX can be easily attached to the TBX table drilling machine.

XENOX KTX MICRO coordinates table

Made of high-strength aluminium (surface compacted) with free from play readjustable dovetail guides.

Three continuous T-grooves (XENOX standard 12 x 6 x 5 mm).

Adjustable ruler facilitates positioning the cross slide. Handwheels with scale ring adjustable to zero:

1 rev = 1.0 mm, 1 graduation line = 0.05 mm feed.

The illustrated clamping jaws and the necessary fastening elements for STX stand and TBX table drilling machine are included. Table 200 x 70 mm. Adjusting range X (diagonal) 134 mm, adjusting range Y

(depth) 46 mm, overall height 42 mm.

No. 68 132

XENOX MSX machine vice

The MSX can be easily positioned on the TBX table drilling machine.

XENOX MSX machine vice

Made of diecast zinc. With three flat-milled bearing surfaces. In addition, a groove as fit for the length stop of the STX stand and as well as the TBX table drilling machine.

Vertical and horizontal prism for round material. Jaw width 50 mm, jaw height 10 mm, maximum span width 34 mm.

The ideal accessory to accurately position tools for drilling, or simply as a «third hand» for holding small parts.

No. 68 128

XENOX TBX table drilling machine

For precise drilling of the smallest of holes the compact XENOX TBX table drilling machine.

XENOX TBX table drilling machine

Flat-milled work table of strongly ribbed aluminium diecast (220 x 120 mm). Parallel limit stop with scale. Massive, hard-chromium plated steel column (Ø 20 x 280 mm). Arm of aluminium diecast with bored guides and fits. High-quality, VDE-approved 230 V motor, 85 watt. Extremely quiet and longlasting.

Triple aluminium belt pulley with flat belt. Three idling speeds by simply shifting the belt: 1,800, 4,700 and 8,500/min (for more than triple the torque in the lower speed range). Sleeve stroke 30 mm.

Practical drill depth indicator with adjustable limit stop.

Extension arm column (column inside up to middle of drill spindle) 140 mm. Maximum working height

140 mm (table surface up to end of spindle).

Precise, ball-bearing free from play work spindle with ground tool holder (6 triple slotted and hardened precision steel collet chucks 1 piece each 1.0 — 1.5 — 2.0 — 2.4 — 3.0 and 3.2 mm) are included. Also a

3/8″ thread for screwing on the toothed ring drill chuck (No. 68 122). With the suitable groove for the

TBX length stop, the MSX machine vice is the ideal clamp accessory for various small parts. The MSC machine vice is not included.

Together with the KTX MICRO coordinates table, the TBX is a precision processing centre.

The KTX is not included.

No. 68 700

XENOX FSX footswitch

XENOX FSX footswitch

For free hands while working. Up to a maximum of 500 watt.

For all devices with Europlug (protection class 2). Also suitable for table top tools. Housing in glassfibre reinforced NYLON. With 250 cm connecting cable to 230 V power mains and 50 cm cable outlet.

For 12 V devices, the foot actuated switch is connected to the transformer.

1

2

3

No. 68 940

XENOX steel collet chucks

XENOX steel collet chucks

1 each for 1.0 — 1.5 — 2.0 — 2.4 — 3.0 and 3.2 mm. With clamping nut and collet chuck holder.

Note:

The steel collet chucks (1) specifically manufactured for our equipment are hardened, giving them a high, consistent spring tension. They retain the requisite precision even after long periods of use.

The triple slitting (2) ensures a better bed (3).

This is important to centrically grasp shafts with smaller diameters.

No. 68 122

Röhm ring gear drill chuck

Röhm ring gear drill chuck

For shafts from 0.5 — 6.0 mm. Approved up to 10,000/min. 3/8″ thread. High degree of true running accuracy. Suitable for TBX table drilling machine. With drill chuck key.

Service

All devices that leave our company have undergone a piece by piece final inspection and test. Even so, should you encounter a problem we are there for you. Please directly address

XENOX Central Service

D-54518 Niersbach/Eifel, Germany

Phone +49 (0) 18 03 – 9 36 69 46 24

Fax +49 (0) 65 75 – 7 81 05

We will respond promptly and reliably and supply you with spare parts upon request.